SkyView - Dynon Avionics
SkyView - Dynon Avionics SkyView - Dynon Avionics
SV-EMS-220 Installation and ConfigurationExample RPM SetupAssume this sensor was mapped on the Sensor Input Mapping Wizard as:PIN # FUNCTION SENSOR NAMEC37 P32/34 RPM RPM RPMNow, we want to configure its alert and graphical properties. Go to the Sensor Setup Menu andopen the RPM RPM Page (SETUP MENU > EMS SETUP > SENSOR SETUP > RPM RPM).Configure RPM RPM with the following properties: ALARM: OFF MAXIMUM GRAPHICAL DISPLAY: 3000 RPM MINIMUM GRAPHICAL DISPLAY: 0 RPM RANGE 1o ENABLEYESo COLORGREENo TOP2000 RPMo BOTTOM0 RPM RANGE 2o ENABLEYESo COLORYELLOWo TOP2250 RPMo BOTTOM2000 RPM RANGE 3o ENABLEYESo COLORGREENo TOP2700 RPMo BOTTOM2250 RPM RANGE 4o ENABLEYESo COLORYELLOWo TOP2750 RPMo BOTTOM2700 RPM RANGE 5o ENABLEYESo COLORREDo TOP3000 RPMo BOTTOM2750 RPMFigure 40–Anatomy of aWidget: RPM7-50 SkyView System Installation Guide - Revision J
SV-EMS-220 Installation and ConfigurationExample Oil Temperature Sensor SetupAssume this sensor was mapped on the Sensor Input Mapping Wizard as:PIN # FUNCTION SENSOR NAMEC37 P7 TEMPERATURE 5/8”-18 NPT FLUID TEMP (100409-000) OILNow, we want to configure its alert and graphical properties. Go to the Sensor Setup Menu andopen the OIL TEMPERATURE Page (SETUP MENU > EMS SETUP > SENSOR SETUP > OILTEMPERATURE).Configure OIL TEMPERATURE with the following properties: ALARM: LATCHING MAXIMUM GRAPHICAL DISPLAY: 260 °F MINIMUM GRAPHICAL DISPLAY: 80 °F RANGE 1o ENABLEYESo COLORYELLOWo TOP 165 °Fo BOTTOM 80 °F RANGE 2o ENABLEYESo COLORGREENo TOP 220 °Fo BOTTOM 165 °F RANGE 3o ENABLEYESo COLORYELLOWo TOP 240 °Fo BOTTOM 220 °F RANGE 4o ENABLEYESo COLORREDo TOP 260 °Fo BOTTOM 240 °F RANGE 5o ENABLENOo COLORREDo TOP 5 °Fo BOTTOM 0 °FFigure 41–Anatomy of aWidget: OilTemperatureNote that oil temperature is configured with a latching alarm in this example. If oiltemperature ever reaches a range configured as red, an alarm will trigger and amessage will show up in the message box on the Main Menu.SkyView System Installation Guide - Revision J 7-51
- Page 81 and 82: 7. SV-EMS-220 Installation and Conf
- Page 83 and 84: SkyView Network ConnectionSV-EMS-22
- Page 85 and 86: SV-EMS-220 Installation and Configu
- Page 87 and 88: SV-EMS-220 Installation and Configu
- Page 89 and 90: SV-EMS-220 Installation and Configu
- Page 91 and 92: SV-EMS-220 Installation and Configu
- Page 93 and 94: SV-EMS-220 Installation and Configu
- Page 95 and 96: SV-EMS-220 Installation and Configu
- Page 97 and 98: SV-EMS-220 Installation and Configu
- Page 99 and 100: SV-EMS-220 Installation and Configu
- Page 101 and 102: SV-EMS-220 Installation and Configu
- Page 103 and 104: SV-EMS-220 Installation and Configu
- Page 105 and 106: Tools and Equipment RequiredSV-EMS-
- Page 107 and 108: SV-EMS-220 Installation and Configu
- Page 109 and 110: Note that you may need access to th
- Page 111 and 112: Fuel Pressure SensorSV-EMS-220 Inst
- Page 113 and 114: SV-EMS-220 Installation and Configu
- Page 115 and 116: SV-EMS-220 Installation and Configu
- Page 117 and 118: SV-EMS-220 Installation and Configu
- Page 119 and 120: SV-EMS-220 Installation and Configu
- Page 121 and 122: SV-EMS-220 Installation and Configu
- Page 123 and 124: EMS Sensor Input MappingSV-EMS-220
- Page 125 and 126: SV-EMS-220 Installation and Configu
- Page 127 and 128: SV-EMS-220 Installation and Configu
- Page 129: Example Contact Sensor SetupAssume
- Page 133 and 134: SV-EMS-220 Installation and Configu
- Page 135 and 136: 8. SV-GPS-250 Installation and Conf
- Page 137 and 138: SV-GPS-250 Installation and Configu
- Page 139 and 140: 9. SV-BAT-320 InstallationThis chap
- Page 141: Battery Status CheckSV-BAT-320 Inst
- Page 144 and 145: Autopilot Servo Installation, Confi
- Page 146 and 147: Autopilot Servo Installation, Confi
- Page 148 and 149: Autopilot Servo Installation, Confi
- Page 150 and 151: Autopilot Servo Installation, Confi
- Page 152 and 153: Autopilot Servo Installation, Confi
- Page 154 and 155: Autopilot Servo Installation, Confi
- Page 156 and 157: Autopilot Servo Installation, Confi
- Page 158 and 159: Autopilot Servo Installation, Confi
- Page 160 and 161: Autopilot Servo Installation, Confi
- Page 162 and 163: Autopilot Servo Installation, Confi
- Page 164 and 165: Autopilot Servo Installation, Confi
- Page 166 and 167: Autopilot Servo Installation, Confi
- Page 168 and 169: Autopilot Servo Installation, Confi
- Page 170 and 171: Autopilot Servo Installation, Confi
- Page 173 and 174: 11. SV-XPNDR-26X Installation, Conf
- Page 175 and 176: SV-XPNDR-26X Installation, Configur
- Page 177 and 178: SV-XPNDR-26X Installation, Configur
- Page 179 and 180: Power/Ground InputSV-XPNDR-26X Inst
SV-EMS-220 Installation and ConfigurationExample Oil Temperature Sensor SetupAssume this sensor was mapped on the Sensor Input Mapping Wizard as:PIN # FUNCTION SENSOR NAMEC37 P7 TEMPERATURE 5/8”-18 NPT FLUID TEMP (100409-000) OILNow, we want to configure its alert and graphical properties. Go to the Sensor Setup Menu andopen the OIL TEMPERATURE Page (SETUP MENU > EMS SETUP > SENSOR SETUP > OILTEMPERATURE).Configure OIL TEMPERATURE with the following properties: ALARM: LATCHING MAXIMUM GRAPHICAL DISPLAY: 260 °F MINIMUM GRAPHICAL DISPLAY: 80 °F RANGE 1o ENABLEYESo COLORYELLOWo TOP 165 °Fo BOTTOM 80 °F RANGE 2o ENABLEYESo COLORGREENo TOP 220 °Fo BOTTOM 165 °F RANGE 3o ENABLEYESo COLORYELLOWo TOP 240 °Fo BOTTOM 220 °F RANGE 4o ENABLEYESo COLORREDo TOP 260 °Fo BOTTOM 240 °F RANGE 5o ENABLENOo COLORREDo TOP 5 °Fo BOTTOM 0 °FFigure 41–Anatomy of aWidget: OilTemperatureNote that oil temperature is configured with a latching alarm in this example. If oiltemperature ever reaches a range configured as red, an alarm will trigger and amessage will show up in the message box on the Main Menu.<strong>SkyView</strong> System Installation Guide - Revision J 7-51