CCI 100 DPC Brochure - Tundra Process Solutions Ltd.

CCI 100 DPCDRAG ® WellheadProduction ChokeValve

2Severe service DRAG ® choke valve delivers precise wellheadpressure control with superior reliability and life.• Improves well productiontime• Enhances control at wellhead• Reduces costs associatedwith maintenance and repair• Improves ability toaccommodate changes inwell operating conditions• Enhances the safety andreliability of productionfacilitiesDrag ® Technology for Severe Service Choke ValvesToday’s gas field environment means higher wellhead pressures withaggressive fluids with entrained sand and other solid particles. Aconventional single stage choke valve is not suitable for this kind of severeservice. The need to maintain production rates means that frequent chokerepair or replacement is no longer acceptable. CCI has responded to thisneed by developing the world’s first true severe service choke valve.CCI has been solving severe service control valve problems in the oil and gasindustry for over 30 years. The CCI severe service choke uses a combinationof proven DRAG ® velocity control technology and the best grades oftungsten carbide material used in the industry to provide long trim life andprecise process control.Typical Conventional Valve Problems Solved by DRAG ®TechnologyRequirementConventionalChoke ValveRoot Cause(s)CCI 100 DPC DRAG ® Wellhead Production Choke ValveFigure 1: Exploded view of DRAG ® chokedisks showing flow pathOperation at highpressure differentialsfor extended periodsof time.Improved control atwellhead.Improved resistanceto erosion due tosand and otherparticulate matterentrained in fluids.Ability toaccommodatesignificant changesin well operatingconditions over time.Safety and reliabilityfor increasinglydemanding andchallengingenvironments.Production timesignificantly reduceddue to frequent repairor replacement oftrims and/or bodies.Inability to preciselycontrol pressure and/or flow.Production timesignificantly reduceddue to frequent repairor replacement oftrims and/or bodies.Replace existing valveto address new welloperating conditions.Operation offacility and healthof employeescompromised dueto rapid erosion topressure boundaryparts, severemechanical vibrationand excessive noise.Inadequate controlof fluid velocitiesresulting in rapiddamage to trimcomponents.Poor rangeabilityinherent to design.Inadequate controlof fluid velocitiesresulting in higherosion rates andrapid damage tocontrol surfaces oftrim components.Inadequate controlof fluid velocitiesresulting in higherosion rates andrapid damage to trimcomponents. Poormaterial selection.Poor rangeability.Inability tosignificantly modifyexisting valve.Inadequate control offluid velocities.

Highly flexible configuration allows for futuredepleted well conditions.3Proven DRAG ® Technology for Effective Control of FluidVelocitiesP1CCI’s DRAG ® disk stack controls flowing velocities throughout the valve trimby forcing the process fluid to follow a tortuous path of right angle turns.Velocity/Energy LimitV1Figure 2: Multi-stage letdownUnacceptableAcceptablePVThe resistance to flow provided by these turns (or stages) limits the trim exitvelocity to a safe level, regardless of the pressure drop. The DRAG ® chokevalve eliminates problems resulting from excessive fluid velocities such astrim and body erosion, noise, vibration and poor process control. The fluidvelocities within the trim of CCI choke valves are typically 1/3 to 1/4 thatof conventional single stage chokes. Velocity control protects the trim fromerosion and increases the trim life many fold.P1Velocity/Energy LimitV1Vvcvc = vena contractaUnacceptableAcceptablePVTable 1: Comparison of energy at trim exit for gases and liquidsmulti-stage vs. single-stageGas - Velocity HeadkPa (psi)Liquid - Velocity Headmeter/sec (ft/sec)PvcPBar (psi)6 Stages 1 Stage 6 Stages 1 StageFigure 3: Single-stage letdownFigure 4: DRAG ® high capacity hybridtrim (cage and disk stack)Figure 5: DRAG ® total velocity trim (fulldisk stack)400 (5800) 6400 (933) 25200 (3675) 71 (233) 280 (918)200 (2900) 1600 (233) 21500 (3135) 50 (164) 197 (646)100 (1450) 700 (102) 10700 (1560) 35 (115) 138 (453)The rate of erosion has been shown to be proportional to the velocity of thefluid by the third to fifth power, which suggests that the erosion rate wouldbe reduced by eight times if the fluid velocity is reduced by half based on aproportionality to the third power.Proven Materials of Construction for Superior WearResistanceCCI chokes utilize solid tungsten carbide trim. The plug is solid tungstencarbide, not just carbide tipped. The disk stack provides for multi-stageletdown and is made from solid tungsten carbide, an industry first. The seatring is provided with a tungsten carbide venturi, allowing for a controlled,erosion resistant expansion into the choke outlet and downstream piping.Proven Engineered Solutions for Maximum Design FlexibilityThe CCI 100DPC Production Choke Valve is designed to accommodate avariety of trim sizes and throttling elements (i.e. disk stacks and cages) inorder to accommodate changes to well operating conditions that will occurover time. Instead of having to purchase an entirely new valve, CCI cansimply re-fit the existing valve with an appropriate trim set that will properlyaddress the new operating conditions.CCI 100 DPC DRAG ® Wellhead Production Choke Valve

4CCI 100 DPC DRAG® Wellhead Production Choke ValveCCI DRAG ® choke features ensure extended operating life.Seals, Gaskets & StemPacking materials selected areexplosive decompression resistantBolted BonnetEasy MaintenanceSolid TungstenCarbide PlugDual Body SealsFor high integrity toxic servicesSolid tungsten carbideeliminates gallingExcellent erosionresistanceLarge balance holeswill not clogPressure Balancing SealsReduces actuator/handwheel forceProvided with dual wiper rings tokeep solids out of sealing areasSolid TungstenCarbide Disk StackSolid tungsten carbidefor erosion resistanceMulti-step letdown tocontrol velocity, erosionand noiseLarge flow passages,easily handle solids anddirty fluidsSolid Tungsten CarbideVenturi SeatSolid tungsten carbideventuri seat in highturbulence zonesVenturi seat transitionflows smoothly into valveoutlet and pipingDRAG ® Disk StackUp to six stages of velocxity control

Use this checklist to evaluate the benefits of the CCIsevere service choke valve.5BenefitsCCI 100 DPCDRAG ® ChokeValveCompetitors1 Solid tungsten carbide plug, seat and disk stack eliminateserosion and galling and extends performance life formaximum productivity.2 Large flow passages to easily handle solids means continuedreliable performance.3 Multi-step letdown to control velocity, erosion, noise, andvibration for minimum down time and safety.4 Increased rangeability due to a longer stroke means superiorperformance and control.5 Dual scrapers prevent solids from entering sealing areas forreduced maintenance.6 Venturi seat transition assures smooth flow into valve outletand piping for problems downstream.7 Easy maintenance, quick-change trim means no trim parts arewelded or screwed into the body.8 One choke body can handle changing wellhead conditions byswapping trim for less down time.9 Up to 6 stages of DRAG ® velocity control ( with total velocitycontrol trim disk stack.)10 All trim seals are PTFE. PTFE is explosive decompressionresistant.CCI 100 DPC DRAG ® Wellhead Production Choke Valve

6Technical specifications and materials.CCI 100 DPC DRAG ® Wellhead Production Choke Valve625341Note:Valve body material is cast as standard. Forged bodies withweld on flanges are available. Consult factory for options.Figure 6: PneumaticDiaphragm78Figure 7: HandwheelActuatorTable 2: MaterialsComponentItemNo.Body 1Bonnet 2Disk Stack 3SeatHousing/Insert4Plug 5StandardNACE MR0175-2002NACE MR0103-2005ASTM A958-SC4130ASTM A352-LCBASTM A216-WCCA995-4A (Duplex)AISI 4130F51/S31803A350-LF2Solid TungstenCarbide17-4/Solid TungstenCarbideSolid TungstenCarbideNACE MR0175-2005/ISO 15156-2 2003/Cor.2.2005(see Note 4)CommentsASTM A958-SC4130ASTM A352-LCBASTM A216-WCCA995-4A (Duplex) See Note 1AISI 4130F51/S31803A350-LF2Solid TungstenCarbideInconel 718/SolidTungsten CarbideSolid TungstenCarbideStem 6 17-4PH Inconel 718 See Note 2Seals 7 PTFE PTFEBody toBonnet SealComponent8 17-4PH Inconel 625(1) ASTM A958-SC4130, A352-LCB, and A216-WCC are available with or withoput an Inconel 625 inlayfor corrision resistance.(2) Inconel 718 is selected for stem material when API material classes FF or HH is specified.(3) Seals are Explosive Decompression Resistant.(4) Certification to NACE is dependant on fluid composition and temperature.Table 3: Performance DataMaterials of ConstructionPressure Rating ANSI 1500-2500, API 5000-10000Actuator TypeStandard Quality LevelOptional Quality LevelsStandard TemperatureRatingsValve CharacteristicsStandard Shut-Off ClassOptional Shut-Off ClassManual handwheel, pneumatic diaphragm orpiston, pneumatic stepper, electric, hydraulicAPI 6A PSL1PSL2 and 3 and NACE MR0175-50 to +250 degF (-45 to +121 degC)(API 6A temperature classifications L, P, R, S, T, U)Figure 8: PneumaticPistonModified equal percentANSI/FCI Class IVANSI/Class VFigure 9: Stepper MotorActuator

CCI DRAG ® choke trim provides performance and reliabilityregardless of your wellhead life cycle.7Table 4: Cv, Stroke, and End ConnectionsDRAG ® High CapacityHybrid Trim (Cage andDisk Stack)Trim SizeRated CvBody Rating1500 ANSIStandard End Connections Sizesfor Specified Trims (See Note 1)Body Rating2500 ANSIBody RatingAPI 5000Body RatingAPI 10000DRAG ® Total VelocityControl Trim(Full Disk Stack))Trim SizeRatedCvStrokeLength(inches)1.0 18 1 1/2, 2, 3” 1 1/2, 2, 3”2 1/16, 2 9/16,3 1/8”1 13/16, 2 1/16,2 9/16, 3 1/16 ”1.0 9 1.51.75 50 3, 4” 3, 4”2 9/16,3 1/8, 4 1/16”2 9/16, 3 1/16,4 1/16”1.75 24 2.52.5 100 4, 6” 4, 6”3 1/8, 4 1/16,5 1/8”3 1/16, 4 1/16,5 1/8”2.5 31 2.53.25 160 4, 6” 4, 6”4 1/16, 5 1/8,7 1/16”4 1/16, 5 1/8,7 1/16”3.25 50 3.54.0 250 6, 8” 6, 8”5 1/8,7 1/16, 9”5 1/8,7 1/16, 9”4.0 60 3.55.0 335 6, 8, 10” 6, 8, 10” 7 1/16, 9” 7 1/16, 9” 5.0 105 4.5(1) Type of end connections include through-hole flanges and hubs(2) For optional sizes and pressure ratings consult factory.Figure 10: DRAG ® high capacity hybrid trim(cage and disk stack)(1) Type of end connections include through-hole flanges and hubsFigure 11: DRAG ® total velocity controltrim (full disk stack)CCI 100 DPC DRAG ® Wellhead Production Choke Valve

8 Technical specifications and materials.CCI 100 DPC DRAG ® Wellhead Production Choke ValveTable 5: Face to Face DimensionsTrimSize1.752.53.2545ANSIClass1500250015002500150025001500250015002500Inlet xOutletCenterline to Inlet FaceDim ACenterline to Outlet FaceDim BSizeRF RTJ RF RTJ3 x 3 10.12 in (257 mm) 10.19 in (259 mm) 10.12 in (257 mm) 10.19 in (259 mm)3 x 4 10.12 in (257 mm) 10.19 in (259 mm) 10.38 in (264 mm) 10.44 in (265 mm)4 x 4 10.38 in (264 mm) 10.44 in (265 mm) 10.38 in (264 mm) 10.44 in (265 mm)3 x 3 12.12 in (308 mm) 12.25 in (311 mm) 12.12 in (308 mm) 12.25 in (311 mm)3 x 4 12.12 in (308 mm) 12.25 in (311 mm) 13.00in (330 mm) 13.19 in (335 mm)4 x 4 13.00 in (330 mm) 13.19 in (335 mm) 13.00in (330 mm) 13.19 in (335 mm)4 x 4 11.62 in (295 mm) 11.69 in (297 mm) 11.62 in (295 mm) 11.69 in (297 mm)4 x 6 11.62 in (295 mm) 11.69 in (297 mm) 13.50 in (343 mm) 13.62 in (346 mm)6 x 6 13.50 in (343 mm) 13.62 in (346 mm) 13.50 in (343 mm) 13.62 in (346 mm)4 x 4 14.25 in (362 mm) 14.44 in (366 mm) 14.25 in (362 mm) 14.44 in (366 mm)4 x 6 14.25 in (362 mm) 14.44 in (366 mm) 17.50 in (445 mm) 17.75 in (451 mm)6 x 6 17.50 in (445 mm) 17.75 in (451 mm) 17.50 in (445 mm) 17.75 in (451 mm)4 x 4 11.62 in (295 mm) 11.69 in (297 mm) 11.62 in (295 mm) 11.69 in (297 mm)4 x 6 11.62 in (295 mm) 11.69 in (297 mm) 13.50 in (343 mm) 13.62 in (346 mm)6 x 6 13.50 in (343 mm) 13.62 in (346 mm) 13.50 in (343 mm) 13.62 in (346 mm)4 x 4 14.25 in (362 mm) 14.44 in (366 mm) 14.25 in (362 mm) 14.44 in (366 mm)4 x 6 14.25 in (362 mm) 14.44 in (366 mm) 17.50 in (445 mm) 17.75 in (451 mm)6 x 6 17.50 in (445 mm) 17.75 in (451 mm) 17.50 in (445 mm) 17.75 in (451 mm)6 x 6 14.50 in (368 mm) 14.62 in (371 mm) 14.50 in (368 mm) 14.62 in (371 mm)6 x 8 14.50 in (368 mm) 14.62 in (371 mm) 18.12 in (460 mm) 18.31 in (465 mm)8 x 8 18.12 in (460 mm) 18.31 in (465 mm) 18.12 in (460 mm) 18.31 in (465 mm)6 x 6 18.50 in (470 mm) 18.75 in (476 mm) 18.50 in (470 mm) 18.75 in (476 mm)6 x 8 18.50 in (470 mm) 18.75 in (476 mm) 22.25 in (565 mm) 22.56 in (573mm)8 x 8 22.25 in (565 mm) 22.56 in (573 mm) 22.25 in (565 mm) 22.56 in (573mm)6 x 6 16.50 in (419 mm) 16.62 in (422 mm) 16.50 in (419 mm) 16.62 in (422 mm)6 x 8 16.50 in (419 mm) 16.62 in (422 mm) 18.12 in (460 mm) 18.31 in (465 mm)8 x 8 18.12 in (460 mm) 18.31 in (465 mm) 18.12 in (460 mm) 18.31 in (465 mm)8 x 10 18.12 in (460 mm) 18.31 in (465 mm) 21.50 in (546 mm) 21.69 in (551 mm)10 x 10 21.50 in (546 mm) 21.69 in (551 mm) 21.50 in (546 mm) 21.69 in (551 mm)6 x 6 20.50 in (521 mm) 20.75 in (527 mm) 20.50 in (521 mm) 20.75 in (527 mm)6 x 8 20.50 in (521 mm) 20.75 in (527 mm) 22.25 in (565 mm) 22.56 in (573mm)8 x 8 22.25 in (565 mm) 22.56 in (573mm) 22.25 in (565 mm) 22.56 in (573mm)8 x 10 22.25 in (565 mm) 22.56 in (573mm) 28.00 in (711 mm) 28.44 in (722 mm)10 x 10 28.00 in (711 mm) 28.44 in (722 mm) 28.00 in (711 mm) 28.44 in (722 mm)

Technical specifications and materials.9Table 5: Face to Face Dimensions (continued)TrimSize1.752.53.2545APIClass500010000500010000500010000500010000500010000Centerline to Inlet FaceCenterline to Outlet FaceInlet x OutletDim ADim BSize6B 6BX 6B 6BX2 9/16 x 2 9/16 9.69 in (246 mm) - 9.69 in (246 mm) -2 9/16 x 3 1/8 9.69 in (246 mm) - 10.19 in (259 mm) -3 1/8 x 3 1/8 10.19 in (259 mm) - 10.19 in (259 mm) -3 1/8 x 4 1/16 10.19 in (259 mm) - 10.44 in (265 mm) -4 1/16 x 4 1/16 10.44 in (265 mm) - 10.44 in (265 mm) -2 9/16 x 2 9/16 - 11.38 in (289 mm) - 11.38 in (289 mm)2 9/16 x 3 1/16 - 11.38 in (289 mm) - 12.00 in (305 mm)3 1/16 x 3 1/16 - 12.00 in (305 mm) - 12.00 in (305 mm)3 1/16 x 4 1/16 - 12.00 in (305 mm) - 13.00 in (330 mm)4 1/16 x 4 1/16 - 13.00 in (330 mm) - 13.00 in (330 mm)3 1/8 x 3 1/8 10.19 in (259 mm) - 10.19 in (259 mm) -3 1/8 x 4 1/16 10.19 in (259 mm) - 11.69 in (297 mm) -4 1/16 x 4 1/16 11.69 in (297 mm) - 11.69 in (297 mm) -4 1/16 x 5 1/8 11.69 in (297 mm) - 12.94 in (329 mm) -5 1/8 x 5 1/8 12.94 in (329 mm) - 12.94 in (329 mm) -3 1/16 x 3 1/16 - 12.00 in (305 mm) - 12.00 in (305 mm)3 1/16 x 4 1/16 - 12.00 in (305 mm) - 13.00 in (330 mm)4 1/16 x 4 1/16 - 13.00 in (330 mm) - 13.00 in (330 mm)4 1/16 x 5 1/8 - 13.00 in (330 mm) - 14.81 in (376 mm)5 1/8 x 5 1/8 - 14.81 in (376 mm) - 14.81 in (376 mm)4 1/16 x 4 1/16 11.69 in (297 mm) - 11.69 in (297 mm) -4 1/16 x 5 1/8 11.69 in (297 mm) - 12.94 in (329 mm) -5 1/8 x 5 1/8 12.94 in (329 mm) - 12.94 in (329 mm) -5 1/8 x 7 1/16 12.94 in (329 mm) - 13.62 in (346 mm) -7 1/16 x 7 1/16 13.62 in (346 mm) - 13.62 in (346 mm) -4 1/16 x 4 1/16 - 14.00 in (356 mm) - 14.00 in (356 mm)4 1/16 x 5 1/8 - 14.00 in (356 mm) - 14.81 in (376 mm)5 1/8 x 5 1/8 - 14.81 in (376 mm) - 14.81 in (376 mm)5 1/8 x 7 1/16 - 14.81 in (376 mm) - 18.75 in (476 mm)7 1/16 x 7 1/16 - 18.75 in (476 mm) - 18.75 in (476 mm)5 1/8 x 5 1/8 13.94 in (354 mm) - 13.94 in (354 mm) -5 1/8 x 7 1/16 13.94 in (354 mm) - 14.62 in (371 mm) -7 1/16 x 7 1/16 14.62 in (371 mm) - 14.62 in (371 mm) -7 1/16 x 9 14.62 in (371 mm) - 18.31 in (465 mm) -9 x 9 18.31 in (465 mm) - 18.31 in (465 mm) -5 1/8 x 5 1/8 - 14.74 in (374 mm) - 14.74 in (374 mm)5 1/8 x 7 1/16 - 14.74 in (374 mm) - 16.18 in (411 mm)7 1/16 x 7 1/16 - 16.18 in (411 mm) - 16.18 in (411 mm)7 1/16 x 9 - 16.18 in (411 mm) - 20.38 in (518 mm)9 x 9 - 20.38 in (518 mm) - 20.38 in (518 mm)7 1/16 x 7 1/16 16.62 in (422 mm) - 16.62 in (422 mm) -7 1/16 x 9 16.62 in (422 mm) - 18.31 in (465 mm) -9 x 9 18.31 in (465 mm) - 18.31 in (465 mm) -7 1/16 x 7 1/16 - 18.18 in (462 mm) - 18.18 in (462 mm)7 1/16 x 9 - 18.18 in (462 mm) - 20.38 in (518 mm)9 x 9 - 20.38 in (518 mm) - 20.38 in (518 mm)CCI 100 DPC DRAG ® Wellhead Production Choke Valve

10Technical specifications and materials.Table 6: Overall Heights and Weights* Dim “D” is 8 in (200 mm) Required for actuator removalCCI 100 DPC DRAG ® Wellhead Production Choke ValveTrimSize1.752.53.2545ANSIClass1500250015002500150025001500250015002500Inlet x OutletSizeMax Overall Height withManual Override Dim Cinch (mm)“Max OverallHeight w/out” ManualOverride Dim C inch (mm)Weightlbs (kg)w/ ActWeightlbs (kg)Bare Stem324 (147)3 x 36343 x 4 68 (1727) 58 (1473)349 (159)(288)4 x 4 374 (170)3 x 3484 (220)8493 x 4 68 (1727) 58 (1473)534 (243)(386)4 x 4 589 (268)4 x 4444 (202)9044 x 6 69 (1753) 59 (1499)544 (247)(411)6 x 6 644 (293)4 x 4697 (317)13774 x 6 69 (1753) 59 (1499)907 (412)(626)6 x 6 1117 (508)4 x 4626 (285)10814 x 6 72 (1829) 61 (1549)726 (330)(491)6 x 6 821 (373)4 x 4994 (452)17044 x 6 72 (1829) 61 (1549)1224 (556)(775)6 x 6 1444 (656)6 x 61004 (456)15646 x 8 72 (1829) 61 (1549)1154 (525)(711)8 x 8 1304 (593)6 x 61728 (785)24636 x 8 74 (1880) 61 (1549)1968 (895)(1120)8 x 8 2203 (1001)6 x 61464 (665)6 x 8 1599 (727)25848 x 8 76 (1930) 63 (1600)1739 (790)(1175)8 x 10 1994 (906)10 x 10 2249 (1022)6 x 62412 (1096)6 x 8 2607 (1185)44998 x 8 76 (1930) 63 (1600)2802 (1274)(2045)8 x 10 3402 (1546)10 x 10 3924 (1784)

Technical specifications and materials.11Table 6: Overall Heights and Weights (continued)TrimSize1.752.53.2545APIClass500010000500010000500010000500010000500010000Inlet x OutletSizeMax Overall Heightwith Manual OverrideDim C inch (mm)“Max OverallHeight w/out” ManualOverride Dim C inch(mm)Weight lbs (kg)Weight lbs (kg)Bare Stem2 9/16 x 2 9/16304 (138)2 9/16 x 3 1/8 314 (143)6343 1/8 x 3 1/8 68 (1727) 58 (1473)324 (147)(288)3 1/8 x 4 1/16 349 (159)4 1/16 x 4 1/16 374 (170)2 9/16 x 2 9/16379 (172)2 9/16 x 3 1/16 404 (184)7693 1/16 x 3 1/16 70 (1778) 58 (1473)424 (193)(350)3 1/16 x 4 1/16 469 (213)4 1/16 x 4 1/16 509 (231)3 1/8 x 3 1/8384 (175)3 1/8 x 4 1/16 414 (188)8394 1/16 x 4 1/16 69 (1753) 59 (1499)444 (202)(381)4 1/16 x 5 1/8 514 (234)5 1/8 x 5 1/8 579 (263)3 1/16 x 3 1/16477 (217)3 1/16 x 4 1/16 517 (235)9174 1/16 x 4 1/16 71 (1803) 59 (1499)557 (253)(417)4 1/16 x 5 1/8 607 (276)5 1/8 x 5 1/8 657 (299)4 1/16 x 4 1/16576 (262)4 1/16 x 5 1/8 636 (289)10015 1/8 x 5 1/8 72 (1829) 61 (1549)701 (319)(455)5 1/8 x 7 1/16 721 (328)7 1/16 x 7 1/16 741 (337)4 1/16 x 4 1/16834 (379)4 1/16 x 5 1/8 874 (397)15945 1/8 x 5 1/8 74 (1880) 61 (1549)919 (418)(725)5 1/8 x 7 1/16 1129 (513)7 1/16 x 7 1/16 1334 (606)5 1/8 x 5 1/8844 (384)5 1/8 x 7 1/16 869 (395)14297 1/16 x 7 1/16 74 (1880) 61 (1549)889 (404)(650)7 1/16 x 9 1029 (468)9 x 9 1169 (531)5 1/8 x 5 1/81113 (506)5 1/8 x 7 1/16 1283 (583)25037 1/16 x 7 1/16 74 (1880) 61 (1549)1453 (660)(1138)7 1/16 x 9 1688 (767)9 x 9 1928 (876)7 1/16 x 7 1/161304 (593)18747 1/16 x 9 76 (1930) 63 (1600)1419 (645)(852)9 x 9 1539 (700)7 1/16 x 7 1/162042 (928)31027 1/16 x 9 76 (1930) 63 (1600)2237 (1017)(1410)9 x 9 2427 (1103)CCI 100 DPC DRAG ® Wellhead Production Choke Valve

Contact us at: info@ccivalve.comFor sales and service locations worldwide,visit us online at: www.ccivalve.comThroughout the world, customers rely on CCI companies to solve theirsevere service control valve problems. CCI has provided custom solutionsfor these and other industry applications for more than 80 years.DRAG is a registered trademark of CCI.©2008 CCI 807 04/08 5K