PROGRAMMABLE UNI-BUG III StItch WELdER - Rapid Welding and ...

Produce uniform high quality welds with the:PROGRAMMABLE UNI-BUG IIIStitch WelderBug-O Systems is guided by honesty, integrity and ethicsin service to our customers and in all we do.

THE UNI-BUG III STITCH WELDER• Produce stitch or continuous welds • Programmable by distance • Runs directly on the workpiece • Carriage attachments designed to run a variety of structural steel profiles.The UNI-BUG III will make continuous or intermittentstitch welds. The machine will mount and run directly on thework piece. The unit is available in a variety of kits. Each kitis designed to fit on a specific steel profile such as flat bar,angle, channel, I-beams and bulb flats (holland profiles).The UNI-BUG III features stitch welding which isprogrammable by distance. If you require stitch welding simplyset the selector switch to the intermittent weld setting andprogram the length of weld required, the length of skip andalso the required delay for pre-flow and burn back. Throughthe use of an integrated weld contactor the UNI-BUG III willactivate and deactivate your wire feeder automatically.UNI-2500, 2502, 2504The UNI-2500 UNI-BUG III Single Torch Kit is equipped for the mounting of a single torch and provides componentsto manually adjust the torch in the vertical and horizontal plane. The UNI-BUG III provides programmable control for stitchor continuous welding and is designed to mount and run on the top edge of a flat bar or stiffener with a minimum height of 2"(50 mm) and a maximum width of 2" (50 mm). The machine will turn on a radius down to 6" (160 mm). The unit will travelat speeds from 4 to 75 inches per minute (102-1905 mm/min).UNI-2600, 2602, 2604The UNI-2600 UNI-BUG III Dual Torch Welding Kit is the same as the UNI-2500, but is equipped for the mounting oftwo welding torches and provides components to manually adjust either torch in the vertical and horizontal plane.2

THE UNI-BUG III STITCH WELDERUNI-2700, 2702, 2704The UNI-2700 UNI-BUG III Dual Torch Bulb Profile Welding Kit is equipped for the mounting of two welding torches andprovides components to independently adjust either torch in the vertical and horizontal plane. The unit features programmablecontrol for stitch or continuous welding and is designed for straight line welding of bulb flats. This unit will mount and run onbulb sizes from 140 mm to 430 mm. The unit will travel at speeds from 4 to 75 inches per minute (102-1905 mm/min).UNI-2800, 2802, 2804The UNI-2800 UNI-BUG III Dual Torch “T” Profile Welding Kit is equipped for the mounting of two welding torchesand provides components to independently adjust either torch in the vertical and horizontal plane. The UNI-2800-4 workson "T" profiles 2''-4'' (51-102 mm) range. The UNI-2800-6 works on "T" profiles 4''-6'' (102-152 mm) range. The unit featuresprogrammable control for stitch or continuous welding and is designed for straight line welding of “T” profiles. This unit willmount and run on top of “T” profiles with a minimum height of 2" (50 mm). The unit will travel at speeds from 4 to 75 inchesper minute (102-1905 mm/min).3

THE UNI-BUG III STITCH WELDERUNI-2900, 2902, 2904The UNI-2900 UNI-BUG III Dual Torch Angle Welding Kit is supplied with the mounts for two welding torches andprovides components to independently adjust either torch in the vertical and horizontal plane. The unit features programmablecontrol for stitch or continuous welding and is designed for straight line welding of angles. The unit will mount and run ontop of angles with a minimum height of 4" (102mm) and widths up to 4" (102mm). The unit will travel at speeds from 4 to 75inches per minute (102-1905mm/min).Technical Data:Dimensions:Power Requirement:UNI-2500, 2600, 2700, 2800, 2900 110 VAC/50-60/1UNI-2502, 2602, 2702, 2802, 2902 240 VAC/50-60/1UNI-2504, 2604, 2704, 2804, 2904 42 VAC/50-60/1Welding Speed Range: 4 ipm to 75 ipm(102 to 1905 mm/min)11.50''(292 mm)7.00''(178 mm)Skip Speed:75 ipm (1905 mm/min)Minimum StiffenerHeight:2'' (50.8 mm)2.00''(51 mm)Net Weight:Shipping Weight:27 lb. (12.2 kg)36.5 lb. (16.6 kg)2.00''(51 mm)6.25''(159 mm)7''-9''(178-229 mm)8.00''(203 mm)BUG-O SYSTEMSWelding & Cutting Automation Since 1948.www.bugo.com 1-412-331-1776A QUALITY PRODUCT FROM BUG-O SYSTEMS • 280 TECHNOLOGY DRIVE • CANONSBURG, PA 15317-9564©A DIVISION OF WELD TOOLING CORPORATION Weld Tooling Corp.ROM 1:16 Litho in U.S.A. LIT-UBIII-BRO-0811