Series MS - SMC

More documents

Recommendations

Info

Miniature Fittings Series MSBushing: MS-5BPlug: MS-5PWidth acrossflats 10Width acrossflats 7Extension Fitting: MS-5JEffective area: 12 mm 2Mass: 5.5 gWidth across flats 7Nipple: MS-5NMass: 1.2 gKMHKKEffective area: 4.0 mm 2Mass: 3.4 gBarb Tee for Soft Tube: MS-5ATHU-3/4/6Model A1 A2 C øDEffective area Mass(mm 2 ) (g)MS-5ATHU-3MS-5ATHU-488.88.38.84.551.61.81.11.43.43.6MS-5ATHU-6 10.8 10.8 7 2.5 2.4 4.2Effective area: 4.0 mm 2Mass: 1.4 gWidth across flats 7DMSLQMQRTMS-5ATHU-3, -4Width across flats 7MS-5ATHU-6Width across flats 7Universal Nipple: MS-5UNWidth acrossflats 8Width acrossflats 8Effective area: 4.0 mm 2Mass: 3.7 g265
Series MSMade to Order SpecificationsPlease contact SMC for detailed dimensions, specifications, and delivery.1Gasket Material ModificationSymbolX83X112Suffix “-X83” to the end of part number.Example) MS-5AU-4-X83SpecificationsGasket material: Stainless steel 304, NBRApplicable threadM5Applicable threadM5Gasket part no.M-5G2Gasket material: Stainless steel 316, Special FKMGasket part no.M-5G3Spare PartsDescriptionGasketPart no.M-5G1M-5G2M-5G3M-5GHApplicable threadM5MaterialPVCStainless steel 304, NBRStainless steel 316, Special FKMNylon 66, GF30%Applicable model———MS-5ALHU-6MS-5HLH-4MS-5HLH-6MS-5ATHU-6Cap nutMS-5-4-P01MS-5-6-P02——Stainless steel 316Stainless steel 316MS-5H-4MS-5HL-4MS-5HLH-4MS-5H-6MS-5HL-6MS-5HLH-6PrecautionsBe sure to read before handling.Refer to front matters 58 and 59 for Safety Instructions and pages 13 to 16 for Fittings and TubingPrecautions.Tightening of M5 ThreadCaution1. Tighten by hand, and give it an additional rotation with awrench.Please check the number of tightening revolutions using thetable below. If tightened excessively, thread portion may bedamaged and gasket may be deformed. This will cause airleakage. On the contrary, if tightened insufficiently, threadmay loosen causing air leakage.ThreadM5ModelMS-5AU-MS-5H-MS-5PMS-5JMS-5NMS-5UNMS-5ALHU-6MS-5HLH-MS-5ATHU-6MS-5ALHU-3, 4MS-5ULMS-5UTMS-5ATHU-3, 4Number of tightening rotationsApprox. 1/6 to 1/4 rotation Note)Approx. 1/2 rotation Note)Note) As a guideline, the tightening torque should be 1 to 1.5 N·m.266CautionUse of Tube with Hose Nipple1. Cut the tube perpendicularly to the tube axis to a little longerlength than required (use tube cutter “TK-1”, “TK-2” or “TK-3”).2. Pass the tube through the cap nut.3. Push the tube until it comes to the end of the barb portion, or itmay cause air leakage or hose releasing.4. Tighten the cap nut firmly by hand on the fitting.Use of Tube with Barb FittingCaution1. Cut the tube perpendicularly to the tube axis to a little longerlength than required (use tube cutter “TK-1”, “TK-2” or “TK-3”).2. Push the tube until it comes to the end of the barb portion, or itmay cause air leakage or release hose.
Page 1 and 2: Miniature FittingsStainless Steel 3
Page 3: Series MSBarb Fitting for Soft Tube

Series MS - SMC

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?