D1d.1 Pages 1-10 Dated 4-10-06 Type SL & NCC.pmd - Paco Pumps

More documents

Recommendations

Info

PACOD1d.17/05Supercedes 1/90PUMPSI. INSTALLATION-MECHANICALTABLE OF CONTENTSA. Pump Identification ..................................................................................................... 3B. Receiving .................................................................................................................... 3C. Temporary Storage...................................................................................................... 3D. Location....................................................................................................................... 3E. Installation ................................................................................................................... 4F. Piping ........................................................................................................................... 5G. External Wiring ........................................................................................................... 5II.OPERATIONA. Pre-Start Checklist....................................................................................................... 4B. Starting The Pump....................................................................................................... 4C. Pump Shutdown .......................................................................................................... 5III.MAINTENANCEA. Motor Lubrication ......................................................................................................... 5B. Pump Thrust Bearing Lubrication ................................................................................ 6C. Pump Intermediate & Lower Bearing Lubrication ........................................................ 6IV.TROUBLESHOOTINGA. Symptoms....................................................................................................................7B. Possible Causes .......................................................................................................... 7V. WARRANTY ........................................................................................................................ 8VI. SALES AND SERVICE CENTERS..................................................................................... 82
PACOD1d.17/05Supercedes 1/90PUMPSI. INSTALLATIONRead these instructions thoroughly before installingand operating your PACO Type ASP and ASP CentrifugalPump. Successful operation depends on carefulattention to the procedures described in Sections 1, 2and 3 of this manual. Keep this instruction manualhandy for future use.A. PUMP IDENTIFICATION• All PACO Pumps are identified by Catalog andSerial Numbers. These numbers are stamped onthe pump nameplate (Fig.1a) affixed to each pumpvolute casing, and should be referred to in allcorrespondence with the Company.PACO PUMPSCAT #:STOCK #:SER #: #GPM: TDH: “”“”“”’ IMP.:B. RECEIVINGFIGURE 1aDIA.“””BROOKSHIRE, TEXAS 34014412• Check pumping unit for shortage and damageimmediately upon arrival. Pump accessories whenrequired are packaged in a separate container andshipped with the unit.dations where applicable.D. LOCATION• Sump should be located so that threre is sufficientaccessibility for maintenance and inspection ofpumping unit. Provide a clear space with ampleheadroom for use of a hoist strong enough to liftand remove the unit.• Prior to installation check pump length againstsump depth for proper dimension.E. INSTALLATION• The pumping unit must be freely suspended fromthe sump cover or sole plate. The clearancebetween the pump suction and the bottom of thesump should not be less than one to two times thepump nominal discharge size for optimum performance.• When a suction strainer is included with a suspendedpumping unit a minimum 1/2” clearancebetween the bottom of the strainer and sump flooris recommended.• NOTE: On SL type sump pumps inteded for usewithout sump covers, the unit may be mounteddirectly on the sump floor.• Brackets supported from the sump wall may beutilized to retain the unit.• If equipment is damaged in transit, promptly reportthis to the carrier’s agent. Make complete notationson the freight bill to speed satisfactoryadjustment by the carrier.• Unload and handle the unit with a sling. Do not liftunit by eye bolts on the motor!C. TEMPORARY STORAGE• If pump is not to be installed and operated soonafter arrival, store it in a clean, dry area ofmoderate ambient temperature.• Rotate the shaft by hand periodically to coatbearing with lubricant and retard oxidation andcorrosion.• Follow motor manufacturer’s storage recommen-FIGURE 2a: Sump Pump, Type SL3
Page 1: PACOD1d.17/05Supercedes 1/90PUMPSPA
Page 5 and 6: PACOD1d.17/05Supercedes 1/90PUMPSF.
Page 9 and 10: PACOD1d.17/05Supercedes 1/90PUMPSof

D1d.1 Pages 1-10 Dated 4-10-06 Type SL & NCC.pmd - Paco Pumps

Create successful ePaper yourself

Delete template?

Save as template?