TILT-UP CONSTRUCTION - Brock White

More documents

Recommendations

Info

SuperiorLifting SystemHow to Remove the T-110 Plastic Recess PlugLifting SystemsCoil InsertsThe T-110 Insert’s location1. in the panel is easily found bylocating the antennae which willproject through the surface ofthe concrete.Using an ordinary claw hammer,tap2. lightly around the antennae, breakingthrough the thin skin of concrete toexpose the insert. Avoid striking theconcrete too hard so as not to breakthrough the plastic recess plug.Drive the claws of the hammer3. down about 3/8” between the endof the recess plug and the concrete.Pry up on the end of the recess4. plug until one half of it pops up to apoint where it is about one third ofthe way out of the concrete.For the time being, leave it as itis and proceed with step #5.Repeat steps #3 and #4 to5. loosen the opposite half of therecess plug.Grasp both halves of the recess6. plug between the thumb and fingerand squeeze.Both halves of the recess plug7. should now be easily removed,exposing the insert.If one half of the recess plug8. should be hard to remove, drivethe claws of the hammer as deeplyas possible between the recessplug and the top of the insert, asshown above. Push forward on thehammer with one quick motion.This will remove the recess plug.Use a blower to remove all9. debris from around the insertand the recess plug. The insertis now ready to receive thelifting hardware.Note: For proper hardware releasedo not “round” out void holes.Proper Hardware UsagePrior to lifting any tilt-up panel, apply an initial load to thecrane lines, making certain that the hardware is properlyattached to the head of the T-110 Insert and that the bail ofthe lifting hardware is aligned with the crane line.LoadWarning! Do not apply a sideward load to the bailof the lifting hardware.LoadMaximum Angle20 oLoadBallBallBallRight Right WrongWrongWarning! Do not modify, weld or alter in any way T-120 Hardware units. Such actions could lead to premature failure of the hardware.30 04-09
SuperiorLifting SystemT-110 Superior Lift Hardware Installation SequenceTop ofPanelTop ofPanelTop ofPanelLifting SystemsCoil Inserts1) T-120 Hardware in open positioncentered over the T-110 Insert.2) The Hardware nestled in the InsertRecess and the Bolt/Release Armengaged. The Bolt/Release Armmust contact the panel surface asshown in the sketch. Chip awayexcess concrete, if necessary, tonest the Bolt/Release Arm on theconcrete surface. Contact a DaytonSuperior Technical Service Center ifunable to nest the Bolt/Release Armon the face of the panel.3) The installation is complete. Erectionmay proceed.T-120 Superior Lift Lifting Hardware Release Sequence1) After the panel erection is complete and the panelhas been properly braced/tied-off, the crane lineshould be relaxed slightly to permit the release ofthe lifting hardware.2) To Release the hardware, apply a quick, evendownward force to the release line. The hardwarestays attached to the crane line and is moved tothe next panel.04-0931
Page 4 and 5: 2 02-09
Page 6: General and TechnicalInformationGen
Page 11 and 12: General andTechnical InformationThr
Page 15 and 16: General andTechnical InformationBon
Page 17 and 18: Panel ErectionInformationPanel Anal
Page 19 and 20: Panel ErectionInformationStress Tab
Page 21 and 22: Panel ErectionInformationStrongback
Page 23 and 24: Panel ErectionInformationonto the s
Page 25 and 26: Panel ErectionInformationStandard R
Page 27 and 28: Panel ErectionInformationBrace and
Page 29 and 30: Dayton SuperiorLifting SystemsDayto
Page 31: SuperiorLifting SystemMinimum Inser
Page 35 and 36: Ground Release IISystemT-41 Ground
Page 37 and 38: Ground Release IISystemHow to use t
Page 39 and 40: Ground Release IISystemT-42 Double
Page 41 and 42: Ground Release IISystemHow to use t
Page 43 and 44: Ground Release IISystemP-52 Swift L
Page 45 and 46: Ground Release IISystemHow To Insta
Page 47 and 48: Ground Release IISystemP-60 Swift L
Page 49 and 50: Gyro Tilt PlusSystemGyro Tilt Plus
Page 51 and 52: Gyro Tilt PlusSystemT-50 Gyro Tilt
Page 53 and 54: Gyro Tilt PlusSystemHow to Remove t
Page 55 and 56: Tilt-Up 3Lifting SystemTILT-UP 3 LI
Page 57 and 58: Tilt-Up 3Lifting SystemHow to Remov
Page 59 and 60: Tilt-Up 3Lifting SystemMinimum Inse
Page 61 and 62: Coil InsertsT-2 Double Pick-up Inse
Page 63 and 64: Coil InsertsHow to use Coil Face In
Page 65 and 66: Coil InsertsTotal System and Safe W
Page 67 and 68: Coil InsertsT-8 Lifting Angle• De
Page 69 and 70: Strongback SystemStrongbacksWhen op
Page 71 and 72: Strongback SystemT-13-D Strongback
Page 73 and 74: Strongback SystemT-63 Aluminum Stro
Page 75 and 76: Bracing InformationBrace LoadingBra
Page 77 and 78: Bracing InformationBrace to Floor S
Page 79 and 80: Bracing InformationKnee, Lateral an
Page 81 and 82: Bracing InformationBracing to Cylin
Page 83 and 84:
Bracing InformationT-13 COIL-ANCHOR
Page 85 and 86:
Bracing InformationT-4 Brace Anchor
Page 87 and 88:
Bracing InformationBrace Length and
Page 89 and 90:
Sandwich PanelConnectorsP-24 Delta
Page 91 and 92:
Sandwich PanelConnectorsDelta Tie I
Page 93 and 94:
Form LinersWhen it is time to choos
Page 95 and 96:
Form LinersWood Patterns4" Wide Age
Page 97 and 98:
Form LinersBlock PatternsBrick Patt
Page 99 and 100:
Form LinersStone PatternsRugged Fla
Page 101 and 102:
Form LinersVinyltite1.500" 1.500"0.
Page 103 and 104:
Form LinersApplication GuideTilt-Up
Page 105 and 106:
MiscellaneousT-58 Double Chamfer St
Page 107 and 108:
MiscellaneousRustications, Chamfers
Page 109 and 110:
MiscellaneousP-80 Shim StripsDayton
Page 111 and 112:
MiscellaneousMetal Supports for Reb
Page 113 and 114:
Cure Miscellaneous andBondbreakerBo
Page 115 and 116:
MiscellaneousCure andBondbreakerSur
Page 117 and 118:
Chemical Miscellaneous & Cement Pro
Page 119 and 120:
MiscellaneousPanel ChecklistFor saf
Page 121 and 122:
MiscellaneousMiscellaneous andChemi
show all

TILT-UP CONSTRUCTION - Brock White

Create successful ePaper yourself

Delete template?

Save as template?