Door Visors Installation Instructions - Bernardi Acura Parts ...
Door Visors Installation Instructions - Bernardi Acura Parts ... Door Visors Installation Instructions - Bernardi Acura Parts ...
2. Push the two brackets on the door visor onto thedoor sash. Insert the front tab under the doormirror base.4. Apply masking tape to the door sash along theupper, front, and rear edges of the door visor asshown. Remove the door visor.SECTIONAL VIEWDOORVISOR5 mm(0.2 in.)DOORSASH5mm(0.2 in.)MASKING TAPEDOORSASHBRACKETDOOR VISOR4319180K5. Using isopropyl alcohol, thoroughly clean the doorsash in the area surrounded by the masking tape.Allow it to dry.DOORMIRRORBASETABAlign the frontend of the doorvisor with thedoor mirrorbase withoutclearance.3. Align the front end of the door visor with the doormirror base so there is no clearance. Adjust thedoor visor so that the distance between the rearedge of the door visor and door sash is 5 mm(0.2 in.).6. While wearing gloves, apply the primer to thedoor sash within the masked off area. Wipe up anyexcess primer at once. Allow the primer to dry forat least 3 minutes, then remove the masking tape.SHADED SURFACE OFDOOR SASH(Thoroughly clean withisopropyl alcohol beforeapplying the primer.)4319190K2 of 7 BII 44686 (1012) © 2010 American Honda Motor Co., Inc. - All Rights Reserved.
7. Remove the adhesive backing from the EPT sealer.Attach the EPT sealer to the door sash, and applypressure. Apply the EPT sealer as shown, with theupper edge in contact with the door sash.VIEW FROM THE SIDEDOOR SASH9. Position the door visor as shown in steps 2and 3.SECTIONAL VIEWDOORVISORDOORSASH5mm(0.2 in.)EPT SEALERIn contactEPT SEALERDOORSASHBRACKET7 mm(0.3 in.)4805030K8. Peel back the adhesive backings, fold them over,and attach them to the front of the door visor withmasking tape.DOORMIRRORBASETABAlign the frontend of the doorvisor with thedoor mirrorbase withoutclearance.DOOR VISOR 4319210K10. While holding light pressure on the door visor,carefully remove the adhesive backing. Using thepalm of your hand, hold the door visor firmlyagainst the door for 30 seconds.2 ADHESIVE BACKINGS(Attach them to thefront of the door visorwith masking tape.)DOOR VISOR4319201KADHESIVE BACKING4319221K© 2010 American Honda Motor Co., Inc. - All Rights Reserved. BII 44686 (1012) 3 of 7
- Page 1: INSTALLATIONINSTRUCTIONSAccessory A
- Page 5 and 6: 16. Apply masking tape to the door
- Page 7: 28. Pull up on the driver’s windo
7. Remove the adhesive backing from the EPT sealer.Attach the EPT sealer to the door sash, and applypressure. Apply the EPT sealer as shown, with theupper edge in contact with the door sash.VIEW FROM THE SIDEDOOR SASH9. Position the door visor as shown in steps 2and 3.SECTIONAL VIEWDOORVISORDOORSASH5mm(0.2 in.)EPT SEALERIn contactEPT SEALERDOORSASHBRACKET7 mm(0.3 in.)4805030K8. Peel back the adhesive backings, fold them over,and attach them to the front of the door visor withmasking tape.DOORMIRRORBASETABAlign the frontend of the doorvisor with thedoor mirrorbase withoutclearance.DOOR VISOR 4319210K10. While holding light pressure on the door visor,carefully remove the adhesive backing. Using thepalm of your hand, hold the door visor firmlyagainst the door for 30 seconds.2 ADHESIVE BACKINGS(Attach them to thefront of the door visorwith masking tape.)DOOR VISOR4319201KADHESIVE BACKING4319221K© 2010 American Honda Motor Co., Inc. - All Rights Reserved. BII 44686 (1012) 3 of 7
Change language