Datasheet - Augier

More documents

Recommendations

Info

6.2 Remote Control ModeSwitch Sn on position “Remote”.Selection of circuit by wire control, Jbus RS485/RS422 or MODBUS TCP.(see#CONTROL AND MONITORING) Interlocking: All selection or deselection by remote control cause the dry contact S1-S2 to open for an average time of 200ms. This contact, inserted into the CCRinterlocking loop, force it to stop during the selection or deselection of circuit.Switching is done when at current 0.6.3 Mains supply LossIn remote control position, the removal of 48Vcc supply (or other voltage) of C1 orCx, or the removal of the main supply, or the removal of the two voltages, causes theswitching on (Lamps “ON”) of the two circuits, but don’t stop the CCR (by interlockaction)In local position, the removal of the mains supply have the same effect.What means that whatever the mode (local or remote control), the removal of themains supply (whether the control voltage is present or not), causes the CCR to runwith all circuits energized.7 Alarm indicationA signal light labelled “ALARM” is present in front of the cubicle.This light lit for 2 seconds after power on and must be off after the 2 seconds.During normal use, the “ALARM” light must be off. It will light on in case of interface boarddefault.IMPORTANT NOTICE :This control inputs configuration, as other configuration elements, are set in factoryaccording the kind of remote control board and the type of control supply.60 21362 CIRCUIT SELECTOR Installation & Maintenance Page 8 / 32
8 CONTROL AND MONITORING8.1 Wire remote control with 20 to 60Vdc control supply8.1.1 Wire remote control with EXTERNAL 20 to 60Vdc control supplyWhen delivered, the CS is configured in factory as :- “External” power supply: see Wiring remote control voltage configuration.Inputs (20 to 60 Vdc only)Terminal T1 Function FAA label Pin Type(if fitted)C1 T1-1 C1 control* B1 Input voltage with respect to CC2 T1-2 C2 control* B2 Input voltage with respect to CC3 T1-3 C3 control* B3 Input voltage with respect to CC4 T1-4 C4 control* B4 Input voltage with respect to CC5 T1-5 C5 control* B5 Input voltage with respect to CC6 T1-6 C6 control* CC Input voltage with respect to CC T1-14 C CCI Common to Pin1 to Pin 6 inputs*The loop is energized when the voltage is supplied on input.i The remote control protection fuse is marked as PFU2 on the interface board (5x20mm250V/500mAT)60 21362 CIRCUIT SELECTOR Installation & Maintenance Page 9 / 32
Page 1: AUGIER SA.1 ère avenue - 2243 - BP
Page 4 and 5: 1.2 DisclaimersThis manual could co
Page 6 and 7: 5 INSTALLATION:Cubicle: It can be f
Page 10: 8.1.2 Wire remote control with INTE
Page 14 and 15: 8.5 RS485/RS422 Serial Link configu
Page 16 and 17: 8.5.3 Serial link parametersThe asy
Page 18 and 19: 8.7 CS control & monitoring using s
Page 20 and 21: 9 INTERMODBUS SOFTWAREThe software
Page 22 and 23: 10 ORDERING INFORMATIONThe Circuit
Page 24 and 25: SELECTOR JBUS TABLEAdr. R/W Mode Me
Page 26 and 27: Adr. R/W Mode Memory Label Detail B
Page 28 and 29: 15 PresentationType FAA, 2 ways :Ty
Page 30 and 31: 60 21362 CIRCUIT SELECTOR Installat
Page 32: 60 21362 CIRCUIT SELECTOR Installat

Datasheet - Augier

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?