LF Lit Sheet - Duro Dyne

hand held PinspottersITEM #27003 LF1000LN - 110 VoltITEM #27004 LF2000LN - 220 VoltLFLFQuality WeldingLike a spotwelder, Duro Dyne pinspotters are resistance welders. Insulation isfastened securely with the inherent strength of a welded fastener.Simple to UseA pin is placed into the welding tip, thewelding tip is pressed against the ductworkand the trigger depressed.Easy HandlingSpecial dynamic balance eases handlingand minimizes operator fatigue.Uniform WeldsEvery pinspotter has a lightweight solidstate timer built into the gun case. Controlledtiming extends the duty cycle andassures uniform weld quality.Fitted Carrying CaseHigh impact plastic carrying case protectsunit when not in use. Case hasstorage pockets for accessories.Proven ReliabilityThousands of these units have proventheir durability in shops and at job sitesthroughout the world.LF 1000/2000 LNLF 1000/2000 LN SpecificationsModel LF-1000 Voltage:Model LF-2000 Voltage:110v, 50/60hz220v, 50/60hzCurrent Draw: 110 Volt: 15 amp average; 25 amp peak.220 Volt: 7 1/2 amp average;12 1/2 amp peak.Weight:9 lbs.Consists of: LF pinspotter with built in solid statetimer and 8 ft. power cable, extra welding tip, high impactplastic carrying case.• For use with PN & LN Pins withPC, LC or NC washers• 9 lbs.• For use on 18 gauge or lighter steelMACHINERY DIVISION© 2009 Duro Dyne CorporationPrinted in USA 10/2009BC027404®

Prim. Volt 110 Cycles 50-60Input 18 Amps Duty Cycle 5%Short Circuit Sec. Current 900 AmpsSecondary Voltage 1.9 VoltsFuse For 25 AmpsSERIAL NO.DURO DYNEMACHINERY CORP.81 Spence StreetBay Shore, NY 11706TMPrim. Volt 110 Cycles 50-60Input 18 Amps Duty Cycle 5%Short Circuit Sec. Current 900 AmpsSecondary Voltage 1.9 VoltsFuse For 25 AmpsSERIAL NO.DURO DYNEMACHINERY CORP.81 Spence StreetBay Shore, NY 11706TMPrim. Volt 110 Cycles 50-60Input 18 Amps Duty Cycle 5%Short Circuit Sec. Current 900 AmpsSecondary Voltage 1.9 VoltsFuse For 25 AmpsSERIAL NO.DURO DYNEMACHINERY CORP.81 Spence StreetBay Shore, NY 11706TMMODEL LF-1000LNPINSPOTTERInStructions For Use1. Insert PN / LN Pin.MODEL LF-1000LNPINSPOTTERMODEL LF-1000LNPINSPOTTERPin3. After pins are welded to the duct (1 pin per1 sq. ft.), press insulation onto pins (pins usedshould be 1/4” longer than insulation thickness).DURO DYNE MACHINERY CORP.81 Spence StreetBay Shore, NY 11706SERIAL NO.Secondary Voltage 1.9 VoltsFuse For 25 AmpsPrim. Volt 110 Cycles 50-60Input 18 Amps Duty Cycle 5%Short Circuit Sec. Current 900 AmpsMODEL LF-1000LNTMPINSPOTTER2. Press gun down firmly. Pull the trigger.TriggerDURO DYNE MACHINERY CORP.81 Spence StreetBay Shore, NY 11706SERIAL NO.Prim. Volt 110 Cycles 50-60Input 18 Amps Duty Cycle 5%Short Circuit Sec. Current 900 AmpsSecondary Voltage 1.9 VoltsFuse For 25 AmpsMODEL LF-1000LNTMPINSPOTTER4. Push clips over pin to hold insulation firmlyin place.ClipOrdering Information for Pins & ClipsThousand Pack26001 PN-34 3/4” Spotter Pins26002 PN-114 1-1 1/4” Spotter Pins26003 PN-200 2” Spotter Pins26004 PN-250 2 1/2” Spotter Pins26149 LN-34 3/4” Dyn-O-Lite Nail26148 LN-150 1-1/2” Dyn-O-Lite Nail26147 LN-250 2-1/2” Dyn-O-Lite Nail26017 PC-1 Steel Spotter Clips26021 NC-1 Nylon Spotter Clips for PN Pins26161 NC-2 Nylon Spotter Clips for LN Pins26145 LC1 Dyn-O-Lite Washer Nails up to 2-1/2in26141 LC2 Dyn-O-Lite Washer Nails 3-1/2in to 5-1/2inBulk Pack (15M per carton)26005 PNB-34 3/4” Spotter Pins26006 PNB-114 1-1 1/4” Spotter Pins26007 PNB-200 2” Spotter Pins26008 PNB-250 2 1/2” Spotter Pin26153 LNB-34 3/4” Dyn-O-Lite Nail26154 LNB-150 1-1/2” Dyn-O-Lite Nail26155 LNB-250 2-1/2” Dyn-O-Lite Nail26019 PCB-1 Steel Spotter Clips26022 NCB-1 Nylon Spotter Clips for PN Pins26162 NCB-2 Nylon Spotter Clips for LN Pins26146 LCB1 Dyn-O-Lite Washer Nails up to 2-1/2inDURO DYNE MACHINERY CORP.81 Spence StreetBay Shore, NY 1170626142 LCB2 Dyn-O-Lite Washer Nails 3-1/2in to 5-1/2inSERIAL NO.Secondary Voltage 1.9 VoltsFuse For 25 AmpsLF 1000DURO DYNE PINS AND CLIPS insure against liner being “pulled back” into ductwork by airpressure. Properly secured pins will support a straight pulling weight of approximately 50 lbs. perpin and clip, and guarantees insulation will not sag or fall, but be held firmly in place.Prim. Volt 110 Cycles 50-60Input 18 Amps Duty Cycle 5%Short Circuit Sec. Current 900 AmpsMODEL LF-1000LNTMPINSPOTTERDuro Dyne East Division, Bay Shore, NY 631-249-9000 Fax: 631-249-8346Duro Dyne Midwest Division, Fairfield, OH 513-870-6000 Fax: 513-870-6005Duro Dyne West Division, Santa Fe Springs, CA 562-926-1774 Fax: 562-926-5778Duro Dyne Canada, Lachine, Quebec, Canada 514-422-9760 Fax: 514-636-0328www.durodyne.com E-mail: durodyne@durodyne.com