Supplier Tooling Manual - Lockheed Martin

More documents

Recommendations

Info

TMS-MC-015Revision 27Page 2 of 3621 February 2012* REVISED ** ADDED_____________________________________________________________________________* TABLE OF CONTENTSPART I. AIRCRAFT ITEMS AND TOOLING - SELLER REQUIREMENTS1.0 GENERAL Page 52.0 TOOLING DEFINITIONS Page 53.0 INTERCHANGEABLE-REPLACEABLE (I/R) Page 84.0 “TO MATCH” HOLE PATTERNS AND OTHER I/R FEATURES Page 115.0 CONTROL OF RECORDS FOR BUYER FURNISHED TOOLING Page 116.0 CERTIFIED PROPERTY LIST (CPL) Form 11300 Page 127.0 CONTROL OF BUYER-FURNISHED TOOLS Page 128.0 TOOL QUALITY CODE CATEGORIES Page 149.0 TOOL PROTECTION AND STORAGE REQUIREMENTS Page 1410.0 SHIPPING INSTRUCTIONS Page 1411.0 TOOLING PERIODIC INSPECTION AND RE-VERIFICATION Page 15(PI/V)12.0 TOOLING PERIODIC INSPECTION AND RE-VERIFICATION Page 18(PI/V) RECORDS13.0 BUYER FURNISHED AND SELLER TO SELLER TRANSFER OF TOOLS Page 1814.0 LOCKHEED MARTIN SUBCONTRACT SOURCE BOOKS Page 20PART II. MANUFACTURED SPECIAL TOOLING ONLY – SELLER REQUIREMENTS1.0 GENERAL Page 212.0 DEFINITIONS Page 213.0 SPECIAL TOOLING INSPECTION AND QUALITY REQUIREMENTS Page 214.0 TOOL IDENTIFICATION AND SHIPPING REQUIREMENTS Page 235.0 PROCESS FOR TRANSFER OF TOOL DESIGNS FROM SELLER Page 24TO BUYER6.0 SEALING CRITICAL LOCATORS Page 247.0 DUPLICATE TOOL MANUFACTURING Page 24IMPORTANT NOTICE: A hard copy of this document may not be the document currently in effect. The current version is ALWAYSthe version on the LOCKHEED MARTIN network.
TMS-MC-015Revision 27Page 3 of 3621 February 2012TABLE OF CONTENTS (cont’d.)8.0 INTERCHANGEABLE- REPLACEABLE (I/R) DESIGN AND MANUFACTURING Page 249.0 NON (I/R) AND NRE DESIGNS AND MANUFACTURING Page 25PART III. INTERNATIONAL SELLER REQUIREMENTS1.0 GENERAL Page 262.0 CONTROL OF SUPPORT EQUIPMENT (SE), MANUFACTURINGTEST EQUIPMENT (MTE) AND SPECIAL TEST EQUIPMENT (STE) Page 263.0 CHANGE AUTHORIZATION Page 274.0 TOOLING PRACTICES FOR BUYER-FURNISHED TOOLS Page 275.0 LISTINGS OF SELLER-FABRICATED/PROCURED ST OR STE Page 276.0 DRAWINGS, SKETCHES, TOOL DESIGNS, ETC. Page 277.0 CALIBRATION AND RE-CALIBRATION OF BUYER-FURNISHED Page 27OR SELLER-FABRICATED STE8.0 TOOLING USE AND TOLERANCE REQUIREMENTS Page 289.0 QUALITY ASSURANCE REQUIREMENTS OF SELLER-OWNED Page 28OR SELLER-FABRICATED PRODUCTION TOOLINGPART IV. APPENDICESAPPENDIX A – REWORK, REPAIR AND COORDINATION GUIDE Page 29LIST OF FIGURES1. DS-1017 I/R Identification Label Page 92. Example of I/R Wear Groove Indicators Page 93. I/R Hole identification Options Page 104. I/R Hole identification Example Page 105. “TO MATCH” HOLE PATTERNS Page 116. I/R TOOL DESIGN REQUIREMENTS Page 257. TOOLING HOLE TOLERANCE Page 308. DOUBLE RAIL (INTERCHANGEABLE) Page 319. DOUBLE RAIL (REPLACEABLE AND NON-I/R, NET OR WITH Page 31EXCESS10. SINGLE RAIL SETBACK TYPE Page 3211. PRODUCTION TOOL TO CONTROL TOOL Page 36TABLESCOORDINATION PIN TOLERANCE (I/R) – Table 1.0 Page 33COORDINATION PIN TOLERANCE – Table 2.0 Page 34PRODUCTION ITEM TO PRODUCTION TOOL – Table 3.0 Page 35IMPORTANT NOTICE: A hard copy of this document may not be the document currently in effect. The current version is ALWAYSthe version on the LOCKHEED MARTIN network.
Page 4 and 5: TMS-MC-015Revision 27Page 4 of 3621
Page 26 and 27: PART IIITMS-MC-015Revision 27Page 2
Page 36: TMS-MC-015Revision 27Page 36 of 362

Supplier Tooling Manual - Lockheed Martin

Create successful ePaper yourself

Delete template?

Save as template?