Welding Equipment - BLUESHIELD

Welding Equipmentwww.airliquide.ca

GMAW Welding Equipment (MIG)GMAW Welding Equipment (MIG)Air Liquide Welding M 132InputOutput0.5 - 4.8 mm (24# - 3/16")Input Output 0.8 - 4.8 mm (24# - 3/16”)Lincoln Power MIG 140CWELDINGEQUIPMENTPART NUMBERLIN-K24711Input Amperage20 A @ Rated OutputAmperage Range30 - 140 ARated Output 90 A / 19.5 V / 20%Maximum OCV33 VWire Feed Speed1.3 - 12.7 m/min (50 - 500 ipm)Dimensions (H x W x D) 357 x 258 x 472 mm (14 x 10.5 x 18.6 in)Net Weight26.3 kg (58 lb)IncludesMagnum 100L Gun 3 m (10 ft), Gas and Gasless Nozzles, Liner, Contact Tips,Work Cable and Clamp, Adjustable Gas Regulator & Hose, Spindle Adapter,0.90 kg (3 lb), Spool of SuperArc L-56 Mild Steel MIG Wire, 0.45 kg (1 lb) SpoolNR-211-NP Flux-Cored Wire, Learn-to-Use DVDWELDINGEQUIPMENTWIRE DIAMETER 0.6 mm (0.023”) 0.8 mm (0.030”) 0.9 mm (0.035”)Contact Tip LIN-KP1123 LIN-KP1130 LIN-KP1135Liner LIN-KP19373 LIN-KP19373 LIN-KP454015Diffuser LIN-KP3550 LIN-KP3550 LIN-KP3550Feed Roll - V-Smooth LIN-KP25291 LIN-KP25291 LIN-KP25292Feed Roll - V-Knurled LIN-KP25293 LIN-KP25293NOZZLE I.D. 9.5 mm (3/8”) 12.7 mm (1/2”) 15.9 mm (5/8”)Nozzle - FlushedLIN-KP2150FNozzle - Recessed LIN-KP21T37 LIN-KP21T50 LIN-KP21T62OPTIONAL ACCESSORIESMagnum 100SG Spool GunProtective CoverLA S-6 wire 0.8mm (0.030”) *ALMIG Shielding Gas *Machine & Cylinder CartLIN-K25321LIN-K23771BLU-38977830GAS-ALMIG16MET-RV130ALRED* General purpose wire / gas combination for mild steel GMAWPlease contact Air Liquide for advice on more specific needsInput Output 0.8 - 4.8 mm (24# - 3/16”)Miller Millermatic 140PART NUMBERALW-M120500428Maximum Input Amperage 25 AAmperage Range30 - 130 ARated Output 90 A / 19 V / 20%Maximum OCV30 VWire Feed Speed3.3 - 22 m/min (50 - 866 in/min)Dimensions (H x W x D) 430 x 270 x 460 mm (17 x 10.5 x 18 in)Net Weight23 kg (50 lb)IncludesAir Liquide Welding 140 A gun with 3 m (10 ft) cable, 3 m (10 ft) work cable andclamp, 2.43 m (8 ft) 115 V power cable with plug, 0.8 - 0.9 mm (0.030 - 0.035")drive roll, gas regulator & hose kit for CO 2or argon blend gases, extra contact tipsPART NUMBERMIL-907311Input Amperage20 A @ Rated OutputAmperage Range30 - 140 ARated Output 90 A / 18 V / 20%Maximum OCV28 VWire Feed Speed1.0 - 12.7 m/min (40 - 500 ipm)Dimensions (H x W x D) 400 x 270 x 445 mm (15.75 x 10.62 x 18.50 in)Net Weight27 kg (60 lb)Includes3 m (10 ft) M-10 MIG Gun and Cable Assembly, 3 m (10 ft) Work Cable with Clamp,Factory-installed Gas Solenoid Valve, Smith Regulator and Gas Hose, 1.8 m (6 ft)Power Cord with Plug, Dual Groove Drive Rolls for 0.6 mm (0.023”) or0.8 - 0.9 mm (0.030 - 0.035”) Wire, Extra Contact Tips, Hobart Spool of Solid Wire,Information/Setting Chart, Set-up and Operation CDSG 185 Spool Gun (Optional)OPTIONAL ACCESSORIESSG 185 Spool GunMG 142 Welding GunALMIG Shielding Gas *LA S-6 Wire 0.8 mm (0.030") *Machine CartALW-SG090055704ALW-MG090055262GAS-ALMIG16BLU-38977830MET-RV130AL* General purpose wire / gas combination for mild steel GMAWPlease contact Air Liquide for advice on more specific needsWIRE DIAMETER 0.6 mm (0.023") 0.8 mm (0.030”) 0.9 mm (0.035”)Contact Tip ALW-SPW000055127 ALW-SP090055172 ALW-SP090055173Liner ALW-SP090055127 ALW-SP090055127 ALW-SP090055127Diffuser ALW-SP090055105 ALW-SP090055105 ALW-SP090055105Feed Roll - V-Smooth ALW-SP800011491 ALW-SP800011491 ALW-SPW000232112Pressure Roll ALW-SP2VCUS06090 ALW-SP2VCUS06090 ALW-SP2VCUS06090NOZZLE I.D. 12.7 mm (1/2")Nozzle - ConicalALW-SPW000010786Nozzle - For Spot WeldingALW-SP090055178WIRE DIAMETER 0.6 mm (0.023”) 0.8 mm (0.030”) 0.9 mm (0.035”)Contact Tip MIL-087299 MIL-000067 MIL-000068Liner MIL-194010 MIL-194011 MIL-194011Diffuser MIL-169716 MIL-169716 MIL-169716Feed Roll - V-Smooth MIL-220179 MIL-220179 MIL-220179Feed Roll - V-Knurled MIL-202926 MIL-202926 MIL-202926NOZZLE I.D. 9.5 mm (3/8”) 12.7 mm (1/2”) 15.9 mm (5/8”)Nozzle - FlushedMIL-169715Gasless Flux-Core NozzleMIL-226190OPTIONAL ACCESSORIESSpoolmate 100 SeriesProtective CoverLA S-6 wire 0.8mm (0.030”) *ALMIG Shielding Gas *Machine & Cylinder CartMIL-300371MIL-195149BLU-38977830GAS-ALMIG16MET-RV130AL* General purpose wire / gas combination for mild steel GMAWPlease contact Air Liquide for advice on more specific needsC-4www.airliquide.caC-5

GMAW Welding Equipment (MIG)GMAW Welding Equipment (MIG)Air Liquide Welding M 172InputOutput0.8 - 6.35 mm (24# - 1/4")Input Output 0.8 - 6.35 mm (24# - 1/4”)Lincoln Power MIG 180CWELDINGEQUIPMENTPART NUMBERLIN-K24731Input Amperage20 A / 230 V @ Rated OutputAmperage Range30 - 180 ARated Output 130 A / 17 V / 30%Maximum OCV33 VWire Feed Speed1.3 - 12.7 m/min (50 - 500 ipm)Dimensions (H x W x D) 357 x 258 x 472 mm (14 x 10.15 x 18.6 in)Net Weight30 kg (66 lb)IncludesMagnum 100L Gun 3 m (10 ft), Gas and Gasless Nozzles, Liner, Contact Tips, WorkCable and Clamp, Adjustable Gas Regulator & Hose, Spindle Adapter, 0.90 kg (3 lb),Spool of SuperArc L-56 Mild Steel MIG Wire, 0.45 kg (1 lb) Spool NR-211-NPFlux-Cored Wire, Learn-to-Use DVDWELDINGEQUIPMENTWIRE DIAMETER 0.6 mm (0.023”) 0.8 mm (0.030”) 0.9 mm (0.035”)Contact Tip LIN-KP1123 LIN-KP1130 LIN-KP1135Liner LIN-KP19373 LIN-KP19373 LIN-KP454015Diffuser LIN-KP3550 LIN-KP3550 LIN-KP3550Feed Roll - V-Smooth LIN-KP25291 LIN-KP25291 LIN-KP25292Feed Roll - V-Knurled LIN-KP25293 LIN-KP25293NOZZLE I.D. 9.5 mm (3/8”) 12.7 mm (1/2”) 15.9 mm (5/8”)Nozzle - FlushLIN-KP2150FNozzle - Recessed LIN-KP21T37 LIN-KP21T50 LIN-KP21T62OPTIONAL ACCESSORIESMagnum 100SG Spool GunProtective CoverLA S-6 Wire 0.8mm (0.030”) *ALMIG Shielding Gas *Machine & Cylinder CartLIN-K25321LIN-K23771BLU-38977830GAS-ALMIG16MET-RV130ALRED* General purpose wire / gas combination for mild steel GMAWPlease contact Air Liquide for advice on more specific needsSG 185 Spool Gun (Optional)Input Output 0.8 - 6.35 mm (24# - 1/4”)Miller Millermatic 180 Auto-SetOPTIONAL ACCESSORIESSG 185 Spool GunMG 142 Welding GunALMIG Shielding Gas *LA S-6 Wire 0.8 mm (0.030") *Machine CartALW-SG090055704ALW-MG090055262GAS-ALMIG16BLU-38977830MET-RV130AL* General purpose wire / gas combination for mild steel GMAWPlease contact Air Liquide for advice on more specific needsPART NUMBERALW-M120500429Maximum Input Amperage 20 AAmperage Range30 - 170 ARated Output 120 A / 20 V / 25%Maximum OCV36 VWire Feed Speed3.3 - 22 m/min (50 - 866 in/min)Dimensions (H x W x D) 430 x 270 x 460 mm (17 x 10.5 x 18 in)Net Weight28 kg (62 lb)IncludesAir Liquide Welding 140 A gun with 3 m (10 ft) cable, 3 m (10 ft) work cable andclamp, 2.43 m (8 ft) 230 V power cable with plug, 0.8 - 0.9 mm (0.030 - 0.035")drive roll, gas regulator & hose kit for CO 2or argon blend gases, extra contact tipsPART NUMBERMIL-907312Input Amperage21.7 A / 230 V @ Rated OutputAmperage Range30 - 180 ARated Output 135 A / 22.5 V / 30%Maximum OCV33 VWire Feed Speed1 - 11.7 m/min (40 - 460 ipm)Dimensions (H x W x D) 400 x 270 x 445 mm (15.75 x 10.62 x 18.50 in)Net Weight33 kg (72 lb)Includes3 m (10 ft) M-10 MIG Gun and Cable Assembly, 3 m (10 ft) Work Cable with Clamp,Factory-installed Gas Solenoid Valve, Smith Regulator and Gas Hose, 1.8 m (6 ft)Power Cord with Plug, Dual Groove Drive Rolls for 0.6 mm (0.023”) or 0.8 - 0.9 mm(0.030 - 0.035”) Wire, Extra Contact Tips, Hobart Spool of Solid Wire,Information/Setting Chart, Set-up and Operation CDWIRE DIAMETER 0.6 mm (0.023") 0.8 mm (0.030”) 0.9 mm (0.035”)Contact Tip ALW-SPW000010820 ALW-SP090055172 ALW-SP090055173Liner ALW-SP090055127 ALW-SP090055127 ALW-SP090055127Diffuser ALW-SP090055105 ALW-SP090055105 ALW-SP090055105Feed Roll - V-Smooth ALW-SP800011491 ALW-SP800011491 ALW-SPW000232112Pressure Roll ALW-SP2VCUS06090 ALW-SP2VCUS06090 ALW-SP2VCUS06090NOZZLE I.D. 12.7 mm (1/2”)Nozzle - ConicalALW-SPW000010786Nozzle - For Spot WeldingALW-SP090055178WIRE DIAMETER 0.6 mm (0.023”) 0.8 mm (0.030”) 0.9 mm (0.035”)Contact Tip MIL-087299 MIL-000067 MIL-000068Liner MIL-194010 MIL-194011 MIL-194011Diffuser MIL-169716 MIL-169716 MIL-169716Feed Roll - V-Smooth MIL-220179 MIL-220179 MIL-220179Feed Roll - V-Knurled MIL-202926 MIL-202926 MIL-202926NOZZLE I.D. 9.5 mm (3/8”) 12.7 mm (1/2”) 15.9 mm (5/8”)Nozzle - FlushMIL-169715Gasless Flux-Core NozzleMIL-226190OPTIONAL ACCESSORIESSpoolmate 100 SeriesProtective CoverLA S-6 Wire 0.8mm (0.030”) *ALMIG Shielding Gas *Machine & Cylinder CartMIL-300371MIL-195149BLU-38977830GAS-ALMIG16MET-RV130AL* General purpose wire / gas combination for mild steel GMAWPlease contact Air Liquide for advice on more specific needsC-6www.airliquide.ca1-800-817-7697C-7

GMAW Welding Equipment (MIG)GMAW Welding Equipment (MIG)Air Liquide Welding M 202 Input Output 0.71 - 9.5 mm (22# - 3/8")Input Output 0.8 - 9.5 mm (24# - 3/8”)Lincoln Power MIG 215XTWELDINGEQUIPMENTPART NUMBERLIN-K27001Input Amperage35 A / 230 V @ Rated OutputAmperage Range30 - 250 ARated Output 170 A / 24 V / 60 %Maximum OCV39 VWire Feed Speed1.3 - 17.7 m/min (50 - 700 ipm)Dimensions (H x W x D) 808 x 408 x 985 mm (31.8 x 18.9 x 38.8 in)Net Weight90 kg (198 lb)IncludesMagnum 250L Gun 4.5 m (15 ft), Work Cable and Clamp, Contact, Tips Liner, DriveRolls, Adjustable Gas Regulator & HoseWELDINGEQUIPMENTEasySwitch TMinput voltage selectionWIRE DIAMETER 0.6 mm (0.023”) 0.8 mm (0.030”) 0.9 mm (0.035”)Contact Tip LIN-KP1425 LIN-KP1430 LIN-KP1435Liner LIN-KP422515 LIN-KP422515 LIN-KP42303515Diffuser LIN-KP52FN LIN-KP52FN LIN-KP52FNFeed Roll - V-Smooth LIN-KP1696030S LIN-KP1696030S LIN-KP1696035SFeed Roll - V-Knurled LIN-KP1697030C LIN-KP1697035CNOZZLE I.D. 9.5 mm (3/8”) 12.7 mm (1/2”) 15.9 mm (5/8”)Nozzle - Flush LIN-KP2337F LIN-KP2350F LIN-KP2362FNozzle - Recessed LIN-KP2337 LIN-KP2350 LIN-KP2362OPTIONAL ACCESSORIESMagnum SG / AdapterProtective CoverDual Cylinder Mounting KitALMIG Shielding Gas *LA S-6 Wire 0.9mm (0.035”) *LIN-K18091LIN-K23781LIN-K17021GAS-ALMIG16BLU-38978435* General purpose wire / gas combination for mild steel GMAWPlease contact Air Liquide for advice on more specific needsInput Output 0.8 - 9.5 mm (24# - 3/8”)Miller Millermatic 212PART NUMBERALW-MW000055268Maximum Input Amperage 35 A / 230 VAmperage Range34 - 220 ARated Output 190 A / 40%Maximum OCV35 VWire Feed Speed3 - 24 m/min (118 - 994 in/min)Dimensions (H x W x D) 980 x 410 x 1080 mm (38 x 16 x 40 in)Net Weight89 kg (196 lb)IncludesParweld XP 8 200 A gun with 4 m (12 ft) cable, 3 m (10 ft) work cable and clamp,2.43 m (8 ft) 115 V power cable with plug, 2 drive roll sets for 0.6 - 0.8 mm(0.023 - 0.030") and 0.9 / 1.2 mm (0.035 / 0.045") wire, gas regulator & hose kitfor CO 2or argon blend gases, running gear and cylinder rackPART NUMBERMIL-907324Input Amperage27 A / 230 V @ Rated OutputAmperage Range 30 - 210Rated Output 160 A / 24.5 V / 60%Maximum OCV34.5 VWire Feed Speed1.3 - 17.7 m/min (50 - 700 ipm)Dimensions (H x W x D) 762 x 483 x 1016 mm (30 x 19 x 40 in)Net Weight86 kg (190 lb)Includes4.5 m (15 ft) 250 A M-25 MIG Gun and Cable Assembly, 3 m (10 ft) Work Cable withClamp, Factory-installed Dual Gas Solenoid Valves, Smith Argon Mix Regulator FlowGauge w/Hose, Factory-installed Running Gear / Cylinder Rack, 0.8 - 0.9mm(0.030 - 0.035”) Reversible Dual Groove Drive Rolls, ExtraContact Tips, Set-upand Operation CDOPTIONAL ACCESSORIESSG 300 Spool GunXP 8 200 A Welding GunPressure Roll Set (2)ALMIG Shielding Gas *LA S-6 0.9 mm (0.035") Wire *ALW-SG090055705PAR-XP200A40EALW-SP1901000180GAS-ALMIG16BLU-38978435* General purpose wire / gas combination for mild steel GMAWPlease contact Air Liquide for advice on more specific needsWIRE DIAMETER 0.6 mm (0.023") 0.8 mm (0.030") 0.9 mm (0.035")Contact Tip PAR-XP200306 PAR-XP200308 PAR-XP200309Liner PAR-XP2024PS1250 PAR-XP2024PS1250 PAR-XP2024PS1250Diffuser PAR-XP2004B PAR-XP2004B PAR-XP2004BM8 Head Assembly PAR-XP2005 PAR-XP2005 PAR-XP2005Feed Roll - V-Smooth ALW-SPW000050096 ALW-SP190100082 ALW-SP190100083Feed Roll - V-Knurled ALW-W00022621 ALW-SPW19010088NOZZLE I.D. 9.5 mm (3/8") 12.7 mm (1/2") 15.9 mm (5/8")Nozzle PAR-XP200210 PAR-XP200213 PAR-XP200216WIRE DIAMETER 0.6 mm (0.023”) 0.8 mm (0.030”) 0.9 mm (0.035”)Contact Tip MIL-087299 MIL-000067 MIL-000068Liner MIL-194010 MIL-194011 MIL-194011Diffuser MIL-169728 MIL-169728 MIL-169728Feed Roll - V-Smooth MIL-087131 MIL-079594 MIL-079595Feed Roll - V-KnurledMIL-079606NOZZLE I.D. 9.5 mm (3/8”) 12.7 mm (1/2”) 15.9 mm (5/8”)Nozzle - Flush MIL-200258 MIL-169726Nozzle - Recessed MIL-169724 MIL-169725OPTIONAL ACCESSORIESSpoolmate 3035Spoolmate Adapter CableProtective CoverALMIG Shielding Gas *LA S-6 Wire 0.9mm (0.035”) *MIL-195016MIL-195287MIL-195142GAS-ALMIG16BLU-38978435* General purpose wire / gas combination for mild steel GMAWPlease contact Air Liquide for advice on more specific needsC-8www.airliquide.ca1-800-817-7697C-9

GMAW Welding Equipment (MIG)GMAW Welding Equipment (MIG)Air Liquide Welding M 252 Input Output 0.71 - 9.37 mm (22# - 1/2")InputOutput0.8 - 12.7 mm (24# - 1/2”)Lincoln Power MIG 255XTWELDINGEQUIPMENTPART NUMBER LIN-K27011 (208/230 V) LIN-K27012 (230/460/575 V)Input Amperage19 A / 575 V @ Rated OutputAmperage Range30 - 300 ARated Output 250 A / 26 V / 40%Maximum OCV40 VWire Feed Speed1.3 - 17.7 m/min (50 - 700 in/min)Dimensions (H x W x D) 808 x 908 x 985 mm (31.8 x 18.9 x 38.8 in)Net Weight100 kg (220 lb)IncludesMagnum 250L gun, 4.5 m (15 ft) work cable and clamp, 3 m (10 ft) 230Vpower cable with plug (LIN-K270-1 only), 0.9 - 1.2 mm (0.035 - 0.045") drive rollsand guide for steel, gas regulator & hose kit for CO 2or argon blend gases.WELDINGEQUIPMENTEasySwitch TMinput voltage selectionWIRE DIAMETER 0.8 mm (0.030”) 0.9 mm (0.035”) 1.2 mm (0.045”)Contact Tip LIN-KP1430 LIN-KP1435 LIN-KP1445Liner LIN-KP422515 LIN-KP42303515 LIN-KP42404515Diffuser LIN-KP52FN LIN-KP52FN LIN-KP52FNFeed Roll - V-Smooth LIN-KP1696030S LIN-KP1696035S LIN-KP1696045SFeed Roll - V-Knurled LIN-KP1697030C LIN-KP1697035C LIN-KP1697045CNOZZLE I.D. 9.5 mm (3/8”) 12.7 mm (1/2”) 15.9 mm (5/8”)Nozzle - Flush LIN-KP2337F LIN-KP2350F LIN-KP2362FNozzle - Recessed LIN-KP2337 LIN-KP2350 LIN-KP2362OPTIONAL ACCESSORIESMagnum SG / AdapterMagnum SG Spool GunCanvas CoverALMIG Shielding Gas *LA S-6 wire 0.9mm (0.035”) *LIN-K24451LIN-K48725LIN-K23781GAS-ALMIG16BLU-38978435* General purpose wire / gas combination for mild steel GMAWPlease contact Air Liquide for advice on more specific needsInput Output 0.8 - 12.7 mm (24# - 1/2”)Miller Millermatic 252PART NUMBERALW-MW000055269Maximum Input Amperage 22 A / 575 VAmperage Range33 - 280 ARated Output 250 A / 35%Maximum OCV52 VWire Feed Speed3 - 24 m/min (118 - 994 in/min)Dimensions (H x W x D) 980 x 410 x 1080 mm (38 x 16 x 40 in)Net Weight108 kg (240 lb)IncludesParweld XP 8 300 A gun with 4 m (12 ft) cable, 3 m (10 ft) work cable and clamp,2.43 m (8 ft) 115 V power cable with plug, 2 drive roll sets for 0.6 - 0.8 mm(0.023 - 0.030") and 0.9 / 1.2 mm (0.035 - 0.045") wire, gas regulator & hose kitfor CO 2or argon blend gases, running gear and cylinder rackPART NUMBER MIL-907121 (208/230 V) MIL-907322 (230/460/575 V)Input Amperage17 A / 575 V @ Rated OutputAmperage Range30 - 300 ARated Output 250 A / 28 V / 60%Maximum OCV38 VWire Feed Speed1.3 - 17.8 m/min (50 - 700 in/min)Dimensions (H x W x D) 762 x 483 x 1016 mm (30 x 19 x 40 in)Net Weight94 kg (207 lb)Includes4.6 m (15 ft) 250 A M-25 MIG gun for 0.8 - 0.9 mm (0.030 - 0.035") wire, 3 m (10 ft)work cable with clamp, factory-installed gas solenoid, argon mix regulator/flow gaugeand hose, 3 m (10 ft) power cord and plug (MIL-907321 only), running gear withcylinder rack, 0.8 - 0.9 mm (0.030 - 0.035") reversible drive rolls, extra contact tips,set-up and operation interactive CDOPTIONAL ACCESSORIESSG 300 Spool GunXP 8 200 A Welding GunPressure Roll Set (2)ALMIG Shielding Gas *LA S-6 Wire 0.9 mm (0.035") *ALW-SG090055705PAR-XP200A40EALW-SP1901000180GAS-ALMIG16BLU-38978435* General purpose wire / gas combination for mild steel GMAWPlease contact Air Liquide for advice on more specific needsWIRE DIAMETER 0.8 mm (0.030") 0.9 mm (0.035") 1.2 mm (0.045")Contact Tip PAR-XP200308 PAR-XP200309 PAR-XP200312Liner PAR-XP2024PS1250 PAR-XP2024PS1250 PAR-XP2024PS1250Diffuser PAR-XP2004B PAR-XP2004B PAR-XP2004BM8 Head Assembly PAR-XP2005 PAR-XP2005 PAR-XP2005Feed Roll - V-Smooth ALW-SP190100082 ALW-SP190100083 ALW-SP190100084Feed Roll - V-Knurled ALW-W00022621 ALW-SPW19010088 ALW-SPW19010088NOZZLE I.D. 9.5 mm (3/8") 12.7 mm (1/2") 15.9 mm (5/8")Nozzle PAR-XP200210 PAR-XP200213 PAR-XP200216WIRE DIAMETER 0.8 mm (0.030") 0.9 mm (0.035") 1.2 mm (0.045")Contact Tip MIL-000067 MIL-000068 MIL-000069Liner MIL-194011 MIL-194011 MIL-194012Diffuser MIL-169728 MIL-169728 MIL-169728Feed Roll - V-Smooth MIL-079594 MIL-079595 MIL-079596Feed Roll - V-Knurled MIL-079606 MIL-079607NOZZLE I.D. 9.5 mm (3/8”) 12.7 mm (1/2”) 15.9 mm (5/8”)Nozzle - Flushed MIL-200258 MIL-169726Nozzle - Recessed MIL-169724 MIL-169725OPTIONAL ACCESSORIESSpoolmatic 30ADual Cylinder RackProtective CoverALMIG Shielding Gas *LA S-6 Wire 0.9mm (0.035”) *MIL-130831MIL-300337MIL-195142GAS-ALMIG16BLU-38978435* General purpose wire / gas combination for mild steel GMAWPlease contact Air Liquide for advice on more specific needsC-10C-11www.airliquide.ca1-800-817-7697

GMAW Welding Equipment (MIG)GMAW Welding Equipment (MIG)Lincoln Power MIG 350MP Input Output 0.8 - 12.4 mm (24# - 1/2")Input Output 0.8 - 4.8 mm (24# - 1/2")Miller Millermatic 350PWELDINGEQUIPMENTPART NUMBERLIN-K24031Input Amperage29 A / 575 V @ Rated OutputAmperage Range5 - 350 ARated Output 300 A / 32 V / 60%Maximum OCV67 VWire Feed Speed1.3 - 17.7 m/min (50 - 700 in/min)Dimensions (H x W x D) 808 x 480 x 985 mm (31.8 x 18.9 x 38.8 in)Net Weight116 kg (255 lb)IncludesMagnum 300 gun and 4.5 m (15 ft) cable, 0.9 - 1.2 mm (0.035 - 0.045") drive rollsand guide for steel, regulator and hose, work clamp and cable, 230V input cordand plugPART NUMBERInput AmperageAmperage RangeRated OutputMaximum OCVWire Feed SpeedDimensions (H x W x D)Net WeightIncludesMIL-90716724 A / 575 V @ Rated Output (1-Phase)5 - 350 A300 A / 32 V / 60% (1-Phase & 3-Phase)90 V1.3 - 18 m/min (50 - 700 in/min)863 x 483 x 1041 mm (34 x 19 x 41 in)82 kg (181 lb)Bernard ® Q300 4.6 m (15 ft) MIG gun with extra Centerfire contact tips,3 m (10 ft) industrial power cord (without plug) 3 m (10 ft) work cable with clamp,argon mix regulator / flow meter, low-mounted running gear/cylinder rack,0.9 - 1.2 mm (0.035 - 0.045") in reversible V-groove drive rolls (order u-groove driverolls for aluminum welding), set-up and operation CDWELDINGEQUIPMENTOPTIONAL ACCESSORIESCanvas CoverDual Cylinder Mounting KitAluminum Feeding KitLA T-91LF 1.6 mm (1/16") Wire *BLUESHIELD 8 Shielding Gas *LIN-K23781LIN-K17021LIN-K21531BLU-37963175GAS-BLU822* General purpose wire / gas combination for mild steel FCAWPlease contact Air Liquide for advice on more specific needsWIRE DIAMETER 0.8 mm (0.030") 0.9 mm (0.035") 1.2 mm (0.045")Contact Tip LIN-KP1430 LIN-KP1435 LIN-KP1445Liner LIN-KP422515 LIN-KP44354515 LIN-KP44354515Diffuser LIN-KP54A LIN-KP54A LIN-KP54AFeed Roll - V-Smooth LIN-KP1696030S LIN-KP1696035S LIN-KP1696045SFeed Roll - V-Knurled LIN-KP1697035C LIN-KP1697035C LIN-KP1697045CNOZZLE I.D. 9.5 mm (3/8") 12.7 mm (1/2") 15.9 mm (5/8")Nozzle - Flushed LIN-KP2337F LIN-KP2350F LIN-KP2362FNozzle - Recessed LIN-KP2337 LIN-KP2350 LIN-KP2362WIRE DIAMETER 0.8 mm (0.030”) 0.9 mm (0.035”) 1.2 mm (0.045")Centerfire Contact Tip BER-T030 BER-T035 BER-T045Liner BER-43015 BER-43115 BER-43115Centerfire Diffuser BER-DS1 BER-DS1 BER-DS1Feed Roll Kit - V-Smooth MIL-046780 MIL-046781 MIL-046782Feed Roll Kit - V-Knurled MIL-046792 MIL-046793NOZZLE I.D. 9.5 mm (3/8”) 12.7 mm (1/2”) 15.9 mm (5/8”)Centerfire Nozzle - Flush, Brass BER-NS1200B BER-NS5800BCenterfire Nozzle - Recessed, Brass BER-NS1218B BER-NS5818BOPTIONAL ACCESSORIESProtective Cover w/Helmet BagDual Cylinder RackSpoolmatic 30A SpoolgunLA T-91LF 1.6 mm (1/16") Wire *BLUESHIELD 8 Shielding Gas *MIL-195142MIL-195299MIL-130831BLU-37963175GAS-BLU822* General purpose wire / gas combination for mild steel FCAWPlease contact Air Liquide for advice on more specific needsLincoln Python-Plus Push-Pull GunInputInputMiller XR-A Aluma Pro Push-Pull GunPART NUMBERLIN-K24471 (4.5 m / 15 ft)LIN-K24472 (7.6 m / 25 ft)LIN-K24473 (15.2 m / 50 ft)Compatible withLincoln Power MIG 300 / Power MIG 350 MPWire Capacity 0.8 - 1.6 mm (0.030 - 1/16")Rated Capacity 200 A / 25 V / 100%Wire Feed20.3 m/min (800 in/min)Net Weight1.13 Kg (2.5 lb)IncludesKnurled drive roll and a grooved idler roll, which will handle both steel andaluminum wire from 0.8 - 1.6 mm (0.030 - 1/16") diameterPART NUMBERSMIL-300000 (4.5 m / 15 ft)MIL-300001 (7.6 m / 25 ft)MIL-300264 (10.6 m / 35 ft)Compatible withMiller Millermatic 350PWire Capacity 0.8 - 1.6 mm (0.030 - 1/16")Rated Capacity 300 A / 100%Wire Feed1.8 - 23 m/min (70 - 900 in/min)Net Weight1.13 Kg (2.5 lb)IncludesKnurled drive roll and a grooved idler roll, which will handle both steel and aluminumwire from 0.8 - 1.6 mm (0.030 - 1/16") diameterOPTIONAL ACCESSORIES4.5 m (15 ft) Snake Skin MKE-93101107.6 m (25 ft) Snake Skin MKE-931012215.2 m (50 ft) Snake Skin MKE-9310123Crystal 4043 1.2 mm (0.045") Wire * BLU-20443812Argon Shielding Gas *GAS-ARG22* General purpose wire / gas combination for aluminum GMAWPlease contact Air Liquide for advice on more specific needsWIRE DIAMETER 0.9 mm (0.035") 1.2 mm (3/64") 1.6 mm (1/16")Contact Tip LIN-KP22172B1 LIN-KP22174B1 LIN-KP22175B1Feed Roll - Knurled LIN-KP22191 LIN-KP22191 LIN-KP22191Feed Roll - Idler LIN-KP22201 LIN-KP22201 LIN-KP22201LINER LENGTH 4.5 m (15 ft) 7.6 m (25 ft) 15 m (50 ft)Harness Liner LIN-KP24631 LIN-KP24632 LIN-KP24633NOZZLE I.D. 9.5 mm (3/8”) 12.7 mm (1/2”) 15.9 mm (5/8”)Copper Nozzle LIN-KP22131 LIN-KP22141 LIN-KP22151WIRE DIAMETER 0.9 mm (0.035”) 1.2 mm (3/64") 1.6 mm (1/16")Contact Tip MIL-206187 MIL-206189 MIL-206191Feed Roll - Knurled MIL-227434 MIL-227434 MIL-227434Feed Roll - Idler MIL-230439 MIL-230439 MIL-230710LINER LENGTH 4.5 m (15 ft) 7.6 m (25 ft) 10.6 m (35 ft)Harness Liner MIL-229887 MIL-229891 MIL-232321NOZZLE I.D. 12.7 mm (1/2”) 15.9 mm (5/8”) 19 mm (3/4")Brass Nozzle MIL-199610 MIL-199613 MIL-199612OPTIONAL ACCESSORIES1.6 mm (1/16") Wire Kit MIL-2307084.5 m (15 ft) Leather Cover MIL-2341097.6 m (25 ft) Leather Cover MIL-234110Crystal 4043 1.2 mm (0.045") Wire *Argon Shielding Gas *BLU-20443812GAS-ARG22* General purpose wire / gas combination for aluminum GMAWPlease contact Air Liquide for advice on more specific needsC-12C-13www.airliquide.ca1-800-817-7697

GMAW Welding Equipment (MIG)GMAW Welding Equipment (MIG)Lincoln CV-400Input Output 0.8 - 12.7 mm (24# - 1/2”)Input Output 0.8 - 12.7 mm (24# - 1/2”)Lincoln Idealarc DC-400WELDINGEQUIPMENTwith Ready-Pak ® PackagePART NUMBERLIN-CK134622P2Input Amperage31 A / 575 V @ Rated OutputAmperage Range60 - 500 ARated Output 400 A / 36 V / 100%Maximum OCV46 VWire Feed Speed1.3 - 20.3 m/min (50 - 800 in/min)Dimensions (H x W x D) 1212 x 648 x 838 mm (47.7 x 25.5 x 33 in)Net Weight203 kg (448 lb)IncludesReady-Pak® package include Lincoln CV-400 welding machine, LF-72 wire feeder(bench model), 0.9 - 1.2 mm (0.035 - 0.045") drive rolls for solid wire, heavy-dutywire reel stand, 3 m (10 ft) control cable, 3 m (10 ft) weld power cable, 3 m (10 ft)work cable and clamp, Magnum 400 gun with 4.5 m (15 ft) cable, flowmeter and gashosePART NUMBERLIN-CK130825P2Input Amperage78 A / 230 V @ Rated OutputAmperage Range60 - 500 ARated Output 400 A / 36 V / 100%Maximum OCV57 VWire Feed Speed1.3 - 20.3 m/min (50 - 800 in/min)Dimensions (H x W x D) 1212 x 648 x 838 mm (47.7 x 25.5 x 33 in)Net Weight215 kg (476 lb)IncludesReady-Pak ® package include Lincoln DC-400 welding machine, LF-72 wire feeder(bench model), 0.9 - 1.2 mm (0.035 - 0.045") drive rolls for solid wire, heavy-dutywire reel stand, 3 m (10 ft) control cable, 3 m (10 ft) weld power cable, 3 m (10 ft)work cable and clamp, Magnum 400 gun with 4.5 m (15 ft) cable, flowmeterand gas hose.with Ready-Pak ® PackageWELDINGEQUIPMENTLincoln CV-400 without Ready-Pak ® : LIN-K134622OPTIONAL ACCESSORIES7.6 m (25 ft) Remote Control LIN-K857Remote Control Adapter LIN-K864LA T-91LF 1.6 mm (1/16") Wire * BLU-37963175ARCAL 211 Shielding Gas * GAS-ARC21150XPRXPR Gas Regulator & Pressure / Flow Gauge BLU-XPR56FM680* General purpose wire / gas combination for mild steel FCAWPlease contact Air Liquide for advice on more specific needsWIRE DIAMETER 0.8 mm (0.030") 0.9 mm (0.035") 1.2 mm (0.045")Contact Tip LIN-KP1430 LIN-KP1435 LIN-KP1445Liner LIN-KP422515 LIN-KP44354515 LIN-KP44354515Diffuser LIN-KP54A LIN-KP54A LIN-KP54AFeed Roll - V-Smooth LIN-KP1696030S LIN-KP1696035S LIN-KP1696045SFeed Roll - V-Knurled LIN-KP1697035C LIN-KP1697035C LIN-KP1697045CNOZZLE I.D. 9.5 mm (3/8") 12.7 mm (1/2") 15.9 mm (5/8")Nozzle - Flushed LIN-KP2337F LIN-KP2350F LIN-KP2362FNozzle - Recessed LIN-KP2337 LIN-KP2350 LIN-KP2362WIRE DIAMETER 0.8 mm (0.030") 0.9 mm (0.035") 1.2 mm (0.045")Contact Tip LIN-KP1430 LIN-KP1435 LIN-KP1445Liner LIN-KP422515 LIN-KP44354515 LIN-KP44354515Diffuser LIN-KP54A LIN-KP54A LIN-KP54AFeed Roll - V-Smooth LIN-KP1696030S LIN-KP1696035S LIN-KP1696045SFeed Roll - V-Knurled LIN-KP1697035C LIN-KP1697045CNOZZLE I.D. 9.5 mm (3/8") 12.7 mm (1/2") 15.9 mm (5/8")Nozzle - Flushed LIN-KP2337F LIN-KP2350F LIN-KP2362FNozzle - Recessed LIN-KP2337 LIN-KP2350 LIN-KP2362Lincoln Idealarc DC-400 without Ready-Pak ® : LIN-K130825OPTIONAL ACCESSORIES7.6 m (25 ft) Remote Control LIN-K857Remote Control Adapter LIN-K864LA T-91LF 1.6 mm (1/16") Wire * BLU-37963175ARCAL 211 Shielding Gas * GAS-ARC21150XPRXPR Gas Regulator & Pressure / Flow Gauge BLU-XPR56FM680* General purpose wire / gas combination for mild steel FCAWPlease contact Air Liquide for advice on more specific needsMiller Deltaweld 452Input Output 0.8 - 12.7 mm (24# - 1/2”)Input Output 0.8 - 12.7 mm (24# - 1/2”)Miller Dimension 452with Stationery PackagePART NUMBERMIL-951128 (with stationery package)Input Amperage25 A / 575 V @ Rated OutputAmperage Range50 - 500 ARated Output 450 A / 38 V /100%Maximum OCV48 VWire Feed Speed1.3 - 19.8 m/min (50 - 780 in/min)Dimensions (H x W x D) 762 x 585 x 966 mm (30 x 23 x 38 in)Net Weight174 kg (384 lb)IncludesMiller Deltaweld 452 welding machine, S-74D wire feeder with Bernard Q-400 gun,Industrial 4/0 kit: consists of regulator/flowmeter with 3 m (10 ft) gas hose,3 m (10 ft) 4/0 feeder weld cable, with lugs, and 4.6 m (15 ft) work cablewith 600 A C-clamp.PART NUMBERMIL-951092 (with stationary package)Input Amperage23 A / 575 V @ Rated OutputAmperage Range50 - 500 ARated Output 450 A / 38 V /100%Maximum OCV80 VWire Feed Speed1.3 - 19.8 m/min (50 - 780 in/min)Dimensions (H x W x D) 826 x 585 x 966 mm (32.5 x 23 x 38 in)Net Weight171 kg (376 lb)IncludesMiller Dimension 452 welding machine, S-74D wire feeder with Bernard Q-400 gun,Industrial 4/0 kit: consists of regulator/flowmeter with 3 m (10 ft) gas hose,3 m (10 ft) 4/0 feeder weld cable, with lugs, and 4.6 m (15 ft) work cablewith 600 A C-clamp.with Stationery PackageMiller Deltaweld 452 without Stationary Package: MIL-903394OPTIONAL ACCESSORIESRemote On/Off ControlProcess Control SelectorLA T-91LF 1.6 mm (1/16") wire *ARCAL 211 Shielding Gas *MIL-042869MIL-042871BLU-37963175GAS-ARC21150XPRXPR Gas Regulator & Pressure / Flow Gauge BLU-XPR56FM680* General purpose wire / gas combination for mild steel FCAWPlease contact Air Liquide for advice on more specific needsWIRE DIAMETER 0.9 mm (0.035") 1.2 mm (0.045") 1.6 mm (1/16")Centerfire Contact Tip BER-T035 BER-T045 BER-T062Liner BER-43115 BER-43115 BER-44215Centerfire Diffuser BER-DS1 BER-DS1 BER-DS1Feed Roll - V-Smooth MIL-151026 MIL-151027 MIL-151029Feed Roll - V-Knurled MIL-151052 MIL-151053 MIL-151055NOZZLE I.D. 9.5 mm (3/8") 12.7 mm (1/2") 15.9 mm (5/8")Centerfire Nozzle - Flush, Brass BER-NS1200B BER-NS5800BCenterfire Nozzle - Recessed, Brass BER-NS1218B BER-NS5818BWIRE DIAMETER 0.9 mm (0.035") 1.2 mm (0.045") 1.6 mm (1/16")Centerfire Contact Tip BER-T035 BER-T045 BER-T062Liner BER-43115 BER-43115 BER-44215Centerfire Diffuser BER-DS1 BER-DS1 BER-DS1Feed Roll - V-Smooth MIL-151026 MIL-151027 MIL-151029Feed Roll - V-Knurled MIL-151052 MIL-151053 MIL-151055NOZZLE I.D. 9.5 mm (3/8") 12.7 mm (1/2") 15.9 mm (5/8")Centerfire Nozzle - Flush, Brass BER-NS1200B BER-NS5800BCenterfire Nozzle - Recessed, Brass BER-NS1218B BER-NS5818BMiller Dimension 452 without Stationary Package: MIL-903255OPTIONAL ACCESSORIESRemote On/Off ControlProcess Control SelectorLA T-91LF 1.6 mm (1/16") Wire *ARCAL 211 Shielding Gas *MIL-042869MIL-042872BLU-37963175GAS-ARC21150XPRXPR Gas Regulator & Pressure / Flow Gauge BLU-XPR56FM680* General purpose wire / gas combination for mild steel FCAWPlease contact Air Liquide for advice on more specific needsC-14C-15www.airliquide.ca1-800-817-7697

GMAW Welding Equipment (MIG)GMAW Welding Equipment (MIG)WELDINGEQUIPMENTLincoln Invertec V350-PROwith Ready-Pak ® PackageInputOutput0.8 - 12.7 mm(24# - 1/2")PART NUMBERLIN-K24371Input Amperage18 A / 575 V / 3-Phase @ Rated OuputAmperage Range5 - 425 ARated Output 350 A / 34 V / 60%Maximum OCV80 VWire Feed Speed1.3 - 20.3 m/min (50 - 800 in/min)Dimensions (H x W x D) 376 x 338 x 709 mm (14.8 x 13.3 x 27.8 in)Net Weight36.7 kg (81 lb)IncludesReady-Pak ® package include Lincoln Invertec V350-PRO welding machine (factorymodel), LF-72 wire feeder (bench model), 0.9 - 1.2 mm (0.035 - 0.045") drive rollsfor solid wire, heavy-duty wire reel stand, 3 m (10 ft) control cable, 3 m (10 ft) weldpower cable, 3 m (10 ft) work cable and clamp, Magnum 400 gun with 4.5 m (15 ft)cable, flowmeter and gas hose, heavy-duty inverter and wire feeder cart.Input Output 0.8 - 12.7 mm (24# - 1/2")PART NUMBERLIN-K23751Input Amperage22 A / 575 V @ Rated OutputAmperage Range5 - 570 ARated Output 450 A / 38 V / 100%Maximum OCV75 VWire Feed Speed1.2 - 30.5 m/min (50 - 1200 in/min)Dimensions (H x W x D) 663 x 505 x 835 mm (26.1 x 19.9 x 32.9 in)Net Weight130 kg (286 lb)Required ItemsPower Wave ® 455M welding machine, Power Feed 10M Ready-Pak ® singlebench model wire feeder, 1.0 - 1.2 mm (0.040 - 0.045") drive roll and guide tubekit, Magnum 400 gun and cable kit, work lead package, Harris ® flowmeter regulator,3 m (10 ft) gas hose.Lincoln Power Wave ® 455Mwith Power Feed 10M Ready-Pak ®WELDINGEQUIPMENTLincoln Invertec V350-PRO without Ready-Pak®: LIN-K17286OPTIONAL ACCESSORIESAdvanced Process PanelDual Cylinder Kit3M Speedglas 9002XLA T-91LF 1.6 mm (1/16") Wire *BLUESHIELD 8 Shielding Gas *LIN-K17631LIN-K170213MC-040011231BLU-37963175GAS-BLU822* General purpose wire / gas combination for mild steel FCAWPlease contact Air Liquide for advice on more specific needsWIRE DIAMETER 0.9 mm (0.035") 1.2 mm (0.045") 1.6 mm (1/16")Contact Tip LIN-KP1435 LIN-KP1445 LIN-KP14116Liner LIN-KP44354515 LIN-KP44354515 LIN-KP4411615Diffuser LIN-KP54A LIN-KP54A LIN-KP54AFeed Roll - V-Smooth LIN-KP1696035S LIN-KP1696045S KP1696116SFeed Roll - V-Knurled LIN-KP1697035C LIN-KP1697045C LIN-KP1697116CNOZZLE I.D. 9.5 mm (3/8”) 12.7 mm (1/2”) 15.9 mm (5/8”)Nozzle - Flushed LIN-KP2337F LIN-KP2350F LIN-KP2362FNozzle - Recessed LIN-KP2337 LIN-KP2350 LIN-KP2362WIRE DIAMETER 0.9 mm (0.035") 1.2 mm (0.045") 1.6 mm (1/16")Contact Tip LIN-KP1435 LIN-KP1445 LIN-KP14116Liner LIN-KP44354515 LIN-KP44354515 LIN-KP4411615Diffuser LIN-KP54A LIN-KP54A LIN-KP54AFeed Roll - V-Smooth LIN-KP1696035S LIN-KP1696045S LIN-KP1696116SFeed Roll - V-Knurled LIN-KP1697035C LIN-KP1697045C LIN-KP1697116CNOZZLE I.D. 9.5 mm (3/8") 12.7 mm (1/2") 15.9 mm (5/8")Nozzle - Flushed LIN-KP2337F LIN-KP2350F LIN-KP2362FNozzle - Recessed LIN-KP2337 LIN-KP2350 LIN-KP2362Lincoln Power Wave® 455M without Ready-Pak®: LIN-K22021OPTIONAL ACCESSORIESDual Cylinder Platform Undercarriage LIN-K15701PTA-26V TIG TorchLIN-K178373M Speedglas 9002X3MC-040011231LA S-6 1.2 mm (0.045") Wire * BLU-38978445BLUESHIELD 6 Shielding Gas * GAS-BLU650* General purpose wire / gas combination for mild steel GMAWPlease contact Air Liquide for advice on more specific needsMiller XMT 350 CC/CVInputOutput0.8 - 12.7 mm (24# - 1/2")Input Output 0.8 - 12.7 mm (24# - 1/2")Miller Axcess 450with MIGRunner PackagePART NUMBERMIL-907233Input Amperage14.1 A / 575 V @ Rated OutputAmperage Range5 - 425 ARated Output 350 A / 34 V / 60%Maximum OCV75 VWire Feed Speed1.9 - 19 m/min (75 - 750 in/min)Dimensions (H x W x D) 432 x 318 x 610 mm (17 x 12.5 x 24 in)Net Weight36.3 kg (80 lb)IncludesMiller XMT 350 CC/CV welding machine, 22A wire feeder, Bernard Q-400 gun,Consumables, 0.9 - 1.2 mm (0.035 - 0.045") drive roll kit, regulator/flow gauge withgas hose, MIGRunner cart with cylinder rack (bottom tray will hold optionalCoolmate 3 (sold separately).PART NUMBERMIL-951090Input Amperage23.1 A / 575 V @ Rated OutputAmperage Range5 - 600 ARated Output 450 A / 44 V / 100%Maximum OCV80 VWire Feed Speed1.3 - 35.56 m/min (50 - 1400 in/min)Dimensions (H x W x D) 787 x 432 x 572 mm (23 x 31 x 39 in)Net Weight73.9 kg (163 lb)IncludesMiller Axcess 450, Axcess wire feeder, 5 m (15 ft) interconnection feeder cable,Bernard Q400 welding gun, Industrial 4/0 kit: consists of regulator/flowmeter with3 m (10 ft) gas hose,3 m (10 ft) 4/0 feeder weld cable, with lugs, and 4.6 m (15 ft)work cable with 600 A C-clamp, 0.9 mm - 1.2 mm (0.035” - 0.045”) drive rolls.with Stationary PackageMiller XMT 350 without MigRunner package: MIL-907161OPTIONAL ACCESSORIESOptima Pulse Remote PendantSpoolmatic 30A3M Speedglas 9002XLA T-91LF 1.6 mm (1/16") Wire *BLUESHIELD 8 Shielding Gas *MIL-043389MIL-1308313MC-040011231BLU-37963175GAS-BLU822* General purpose wire / gas combination for mild steel FCAWPlease contact Air Liquide for advice on more specific needsWIRE DIAMETER 0.9 mm (0.035") 1.2 mm (0.045") 1.6 mm (1/16")Centerfire Contact Tip BER-T035 BER-T045 BER-T062Liner BER-43115 BER-43115 BER-44215Centerfire Diffuser BER-DS1 BER-DS1 BER-DS1Feed Roll - V-Smooth MIL-079595 MIL-079596 MIL-079598Feed Roll - V-Knurled MIL-079606 MIL-079607 MIL-079609NOZZLE I.D. 9.5 mm (3/8") 12.7 mm (1/2") 15.9 mm (5/8")Centerfire Nozzle - Flush, Brass BER-NS1200B BER-NS5800BCenterfire Nozzle - Recessed, Brass BER-NS1218B BER-NS5818BWIRE DIAMETER 0.9 mm (0.035") 1.2 mm (0.045") 1.6 mm (1/16")Centerfire Contact Tip BER-T035 BER-T045 BER-T062Liner BER-43115 BER-43115 BER-44215Centerfire Diffuser BER-DS1 BER-DS1 BER-DS1Feed Roll - V-Smooth MIL-151026 MIL-151027 MIL-151029Feed Roll - V-Knurled MIL-151052 MIL-151053 MIL-151055NOZZLE I.D. 9.5 mm (3/8") 12.7 mm (1/2") 15.9 mm (5/8")Centerfire Nozzle - Flush, Brass BER-NS1200B BER-NS5800BCenterfire Nozzle - Recessed, Brass BER-NS1218B BER-NS5818BMiller Axcess 450 without wire feeder and gun: MIL-907152OPTIONAL ACCESSORIESPALM ® Convenience PackageRMD Software Package3M Speedglas 9002XLA S-6 1.2 mm (0.045") Wire *BLUESHIELD 6 Shielding Gas *MIL-195517MIL-1952523MC-040011231BLU-38978445GAS-BLU650* General purpose wire / gas combination for mild steel GMAWPlease contact Air Liquide for advice on more specific needsC-16C-17www.airliquide.ca1-800-817-7697

GMAW Welding Equipment (MIG)GMAW Welding Equipment (MIG)WELDINGEQUIPMENTTRE - M 4 0 1 5 4 5Choose a power pin:• Leave Blank fora #4 Pin• E - Euro• B - Bernard• M - Miller• LN - Lincoln• ES - ESAB• LT - L-TEC• PA - Panasonic• OX - OXO• TW - TWECO #5Choose theamperage:• 30 - 350 amp• 40 - 450 amp• 50 - 550 ampSEMI-AUTOMATICMIG TORCHESBuilt-To-Order For Heavy-Duty ApplicationsHave your MIG torch configured and delivered exactly the way you want it! All TOUGH GUN ® Semi-Automatic MIG Torchesare assembled at our plant to match your specifications.SAMPLE BASIC PART NUMBER:The example below represents a 450 amp (40) semi-automaticair-cooled MIG torch equipped with a Miller power pin (M), 15-foot unicable(15) and set up for 0.045" wire (45). Each of the basic parts canbe exchanged for items in the boxes below.Choose thelength:• 10 - 10-ft• 12 - 12-ft• 15 - 15-ft• 20 - 20-ft• 25 - 25-ftCall for otherlengthsChoose thewire size:• 23 - .023"• 30 - .030"• 35 - .035"• 1.0 - 1 mm• 45 - .045"• 52 - .052"• 116 - 1/16"TOUGH GUN Torches are also available in water-cooled models.TORCH STANDARDS CHARTUse this chart to identify the standard parts that are assembled on a basic torch out of the factory.AMPS GOOSENECK NOZZLE RETAINING HEAD GOOSENECK CONTACT TIP POWER PININSULATOR350 305-60 (60 Degree) 401-6-62 404-20 (HD TOUGH LOCK ® ) 402-11 403-20-XX (HD TOUGH LOCK) 214 (Tweco #4)450 405-60 (60 Degree) 401-6-62 404-20 (HD TOUGH LOCK) 402-11 403-20-XX (HD TOUGH LOCK) 214 (Tweco #4)550 505-60 (60 Degree) 401-5-75 404-20 (HD TOUGH LOCK) 402-11 403-20-XX (HD TOUGH LOCK) 214 (Tweco #4)TOUGH GUN TorchTORCH AMPERAGE RATINGS100% DUTY CYCLE 60% DUTY CYCLEPURE CO2 MIXED GASES PURE CO2 MIXED GASES350 AMP 350 250 450 350450 AMP 450 325 575 450550 AMP 550 400 700 550NOTE: Ratings are based on tests that comply with NEMA ARC Welding Section Standard 11-6-1975for Duty Cycle. “The time period of one complete cycle shall be 10 minutes” (60% = 6 minutes).National Electrical Manufacturers Association, 2101 L Street N.W. Washington D.C. 20037ROBOTIC MIG TORCHESBuilt-To-Order for Robotic MIG Welding ApplicationsHave your MIG torch configured and delivered exactly the way you want it! All TOUGH GUN ®Robotic MIG Torches are assembled at our plant to match your specifications.SAMPLE BASIC PART NUMBER:The part number below would be used to build a 500 amp (54) robotic air-cooled torchwith Miller power pin (M), 15-foot cable (15), and consumables for .045" wire (45).Choose a power pin:• Leave Blank for a #4 Pin• E - Euro• B - Bernard• M - Miller• LN - Lincoln• TW - TWECO #5• PA - PanasonicTRE - M 5 4 1 5 4 5Series Number:54 -500 A/C RoboticChoose the length:• 4 - 4-ft• 4.5 - 4.5-ft• 5 - 5-ft• 6 - 6-ft• 8 - 8-ft• 10 - 10-ft• 12 - 12-ft• 15 - 15-ftTORCH STANDARDS CHARTUse this chart to identify the standard parts that are assembled on a basic torch out of the factory.AMPS GOOSENECK NOZZLE RETAINING HEAD GOOSENECK CONTACT TIP POWER PININSULATOR500 405-180QC (60 Degree) 401-6-62 404-30 (HD TOUGH LOCK ® ) 402-11 403-20-XX (TOUGH LOCK) 214 (Tweco #4)TORCH AMPERAGE RATINGS500 AMP ROBOTIC 100% DUTY CYCLE 60% DUTY CYCLETOUGH GUN TORCH PURE CO2 MIXED GASES PURE CO2 MIXED GASES500 AMP 500 350 650 500Choose the wire size:• 30 - .030"• 35 - .035"• 1.0 - 1 mm• 45 - .045"• 52 - .052"• 116 - 1/16"• 564 - 5/64"• 332 - 3/32"CLUTCH AND MOUNTING ARMSITEM PART # DESCRIPTIONCLUTCH AS-708 SAFETY CLUTCHARM AS-306-1 ARM FOR 22° GOOSENECKAS-306-2 ARM FOR 45° GOOSENECKAS-306-3 ARM FOR 60° GOOSENECKARM FOR 180° GOOSENECKWELDINGEQUIPMENTSTEP #1 - PICK YOUR CHASSISAMPERAGE MODEL # DUTY CYCLE RATING LENGTHC02 MixedXS1810 180 120 10’180 XS XS1812 180 120 12’XS1815 180 120 15’XSE1810 180 120 10’180 XSEUROXSE1812 180 120 12’XSE1815 180 120 15’XS2610 260 180 10’260 XS XS2612 260 180 12’XS2615 260 180 15’XSE2610 260 180 10’260 XSEUROXSE2612 260 180 12’XSE2615 260 180 15’XS3210 300 200 10’300 XS XS3212 300 200 12’XS3215 300 200 15’XL3010 300 200 10’300 XL XL3012 300 200 12’XL3015 300 200 15’XL4010 400 275 10’400 XL XL4012 400 275 12’XL4015 400 275 15’SEMI-AUTOMATICMIG TORCHESFor Light to Medium-Duty ApplicationsThe TGX ® program offers you the flexibility of custom building an air-cooled MIG torchto match your welding application.STEP #2 - PICK YOUR POWER PINFEEDER PART # FEEDER TYPECENTURY X214-5 Powercon FeederESAB X214-4 Feeders with “MT” style Quick Connect BlockHOBART X214 Beta-Mig (New Style), Beta-Mig 250 and 251, Dual Feeder,Digital 2000, Dual Digital, Porta Feed 17, Ultra Feed 1000,2000, 2400, Handler, Oscawa, Hefty CV/CCX214-1 Beta-Mig 261 (Part # 903533), Olympic 22-P, Olympic VSX214-4 Handler 120 and 150, Beta-Mig 170, Porta Wire CC/CV,2200 Feeder, 2210 FeederX214-12 2000, 2400X214-29 Handler 135 and 175LINCOLN X214-2 LN7, LN8, LN9, LN22, LN25, Suitcase, SP-150, SP-200, LN742MILLER X214-1 Cricket, Intellimatic, Sidekick, D-51A, Millermatic 130, 150,200, 250, MM-35 (new), New Automatic 1, Portomig, S32P,S-42GL, S-52A, S-54A, Swing-Arc Dualswing, Arc-Single,S-325, 52D, 54D, 52E, 54E, Shopmaster 300, 22 Series,All 60 Series, Millermatic 130 XP, Challenger 172, 185,Vintage, 250XX214-6 Cricket, Intellimatic, Sidekick, D-51A, Millermatic 130, 150,200, 250, MM-35 (new), New Automatic 1, Portomig, S32P,S-42GL, S-52A, S-54A, Swing-Arc Dualswing, Arc Single,S-32S, 52D, 54D, 52E, 54E, Shopmaster 300,22 Series. All 60 Series, Millermatic 130 XP, Challenger 172,185, Vintage, 250XPANASONIC X214-13 Gun Slinger 260(Euro style chassis do not require a power pin)STEP #3 - PICK YOUR LINER / TIPPART # WIRE SIZE KIT CONTENTSXS23 0.023" 415-23-15 LINER / X403-14-23 TIPXS30 0.030" 415-35-15 LINER / X403-14-30 TIPXS35 0.035" 415-35-15 LINER / X403-14-35 TIPXS45 0.045" 415-35-15 LINER / X403-14-45 TIPXL35 0.035" 415-35-15 LINER / X403-20-35 TIPXL45 0.045" 415-35-15 LINER / X403-20-45 TIPXL52 0.052" 415-116-15 LINER / X403-20-52 TIPXL16 1/16" 415-116-15 LINER / X403-20-116 TIPXL116 1/16" 415-564-15 LINER / X403-20-116 TIPGOOSENECKNOTE: Ratings are based on tests that comply with NEMA ARC Welding Section Standard 11-6-1975for Duty Cycle. “The time period of one complete cycle shall be 10 minutes” (60% = 6 minutes).National Electrical Manufacturers Association, 2101 L Street N.W. Washington D.C. 20037DIAMETER 0.75" / 19 mm(NOMINAL SIZE FOR ALL NECKS)‘D’ RADIUSINSULATING DISCCLUTCHMOUNTING ARMINSULATING DISCSPART # DESCRIPTIONPART # DESCRIPTIONAS-101-01 BLANK INSULATING DISCAS-103-4 KUKA: GENESIS KR15AS-101-12 FANUC: MAC-500AS-102-11 HITACHI: M5030, M6030PANASONIC: AW 0500AS-104-3 MILACRON: OTHERAS-101-2 ABB: IRB 6, 1400, 1500, 2000 AND 2400AS-105-1 MILLER: MRK-5FANUC: 100, 100i, 120i, S-6MOTOMAN: SK6, SK16AS-105-2 MILLER: MRH-2, MRH-5, MR-1000MILLER: MRV-2OTC: MRV-6, EX-V6, EX-V6L, EX-V16, DR 4400AS-106-1 MOTOMAN: L10W, L106, L10G PANASON-IC : AW7000DAIHEN: DR-4000, DR-4200AS-106-3 MITSUBISHI: MZ10AAS-101-3 OTC: IRBC-602AS-106-4 PANASONIC: VR-008A, VR-006A, VR-005C,AS-101-4 ABB: IRB 2400/10, IRB 2400/16, IRB 4400LVR-006ALII, AW-010A, AW-8010, AW-005AAS-101-6 OTC - NOT USED WITH TREGASKISS CLUTCH,& C & CL, AW-006A, VR-008A, VR-006ALONLY AS-306-47-3 MOUNTAS-106-7 MOTOMAN: SV3, SV3X, K3AS-102-10 HITACHI: M5030, M6030 MILLER: MRV-6STAUBLI: RX90AS-106-8 FANUC: ARCMATE 50ILMOTOMAN: K6, K6SB, K10, SK16X, UP6,UP20, MRV6AS-106-9 KAWASAKI: FS10L, FS20REIS: RV16, RV16L, RH16, RH16A4, RL26A4ABB: IRB 1400 M97A and IRB 2400LKAWASAKI: JS06, JS06L, FS06, FS06N, FSO6LAS-107-1 NACHI: 760-SAS-102-12 PANASONIC: AW 500AS-107-2 NACHI: VORG-35AS-102-13 KUKA: KR6/2AS-107-3 NACHI: SC-15, SR-15A-01AS-102-5 KUKAAS-107-4 NACHI: SC-50, SC-35A01AS-102-7 HITACHI: PW-10, 6100REIS: RH70 MOTOMAN: SK45AS-103-3 FANUC: S-5, JR (55), SR (510), S5 AS-107-7 NACHI: SC06F-01, SC06F-02KUKA: KR-15AS-110-1 PUMAGOOSENECK DIMENSIONSGOOSENECK A B C D EINCHES MM INCHES MM INCHES MM INCHES MM405-22QC 22° 9.355 237.6 4.00 103 2.00 51 1.90 48405-45QC 45° 7.607 193.6 3.55 90 3.00 76 1.90 48405-60QC 60° 7.664 194.7 4.78 121 3.00 76 1.90 48405-180QC 180° 8.816 223.9 – – – – 1.90 48Three TGX models are available pre-assembled through our TGX Ready To Weld Program:XS2615, XL3015, and XL4015.TOUGH GUN Torches are also available in water-cooled models.C-18www.airliquide.ca1-800-817-7697C-19

GMAW Welding Equipment (MIG)GMAW Welding Equipment (MIG)AIR COOLED MIG GUNSXP8 200 Amp Mixed Gas (80/20) @ 80% Duty Cycle 0.6mm to 1.2mm wire3m/10ft 4m/13ft 5m/16ftWelding Gun c/w Euro Fitting PAR-XP200A30E PAR-XP200A40E PAR-XP200A50ERWelding Gun c/w Tweco Fitting PAR-XP200A30T PAR-XP200A40T PAR-XP200A50TRWelding Gun c/w Miller Fitting PAR-XP200A30M PAR-XP200A40M PAR-XP200A50MRWelding Gun c/w Lincoln Fitting PAR-XP200A30L PAR-XP200A40L PAR-XP200A50LRWelding Gun c/w Hobart Fitting PAR-XP200A30H PAR-XP200A40H PAR-XP200A50HXP8 300 Amp Mixed Gas (80/20) @ 80% Duty Cycle 0.8mm to 1.2mm wireWELDINGEQUIPMENTThe Parweld XP8 MIGGun sets newstandards in design,innovation andperformancePatented gas flowtechnology increasesboth operationalamperage and dutycycleExtended consumablelife expectancySuperior ergonomics3m/10ft 4m/13ft 5m/16ftWelding Gun c/w Euro Fitting PAR-XP300A30E PAR-XP300A40E PAR-XP300A50ERWelding Gun c/w Tweco Fitting PAR-XP300A30T PAR-XP300A40T PAR-XP300A50TRWelding Gun c/w Miller Fitting PAR-XP300A30M PAR-XP300A40M PAR-XP300A50MRWelding Gun c/w Lincoln Fitting PAR-XP300A30L PAR-XP300A40L PAR-XP300A50LRWelding Gun c/w Hobart Fitting PAR-XP300A30H PAR-XP300A40H PAR-XP300A50HXP8 350 Amp Mixed Gas (80/20) @ 80% Duty Cycle 0.9mm to 1.6mm wire3m/10ft 4m/13ft 5m/16ftWelding Gun c/w Euro Fitting PAR-XP350A30E PAR-XP350A40E PAR-XP350A50ERWelding Gun c/w Tweco Fitting PAR-XP350A30T PAR-XP350A40T PAR-XP350A50TRWelding Gun c/w Miller Fitting PAR-XP350A30M PAR-XP350A40M PAR-XP350A50MRWelding Gun c/w Lincoln Fitting PAR-XP350A30L PAR-XP350A40L PAR-XP350A50LRWelding Gun c/w Hobart Fitting PAR-XP350A30H PAR-XP350A40H PAR-XP350A50HXP8 400 Amp Mixed Gas (80/20) @ 80% Duty Cycle 0.9mm to 2.4mm wire3m/10ft 4m/13ft 5m/16ftWelding Gun c/w Euro Fitting PAR-XP400A30E PAR-XP400A40E PAR-XP400A50ERWelding Gun c/w Tweco Fitting PAR-XP400A30T PAR-XP400A40T PAR-XP400A50TRWelding Gun c/w Miller Fitting PAR-XP400A30M PAR-XP400A40M PAR-XP400A50MRWelding Gun c/w Lincoln Fitting PAR-XP400A30L PAR-XP400A40L PAR-XP400A50LRWelding Gun c/w Hobart Fitting PAR-XP400A30H PAR-XP400A40H PAR-XP400A50HR Registered Trade MarkWELDINGEQUIPMENT1135657 8769XP8-200AXP8-300AXP8-350AXP8-400A241011212C-20www.airliquide.ca1-800-817-7697C-21

GTAW Welding Equipment (TIG)GTAW Welding Equipment (TIG)GTAW welding cycleGTAW (TIG) welding processPreflowArc startWeldingSlopedownandpost-flowGTAW installationPressureregulator/flowmeterInertweldinggasFiller metal rodTorchGTAW metal transferWELDINGEQUIPMENTWELDING CURRENTPreflowInitial currentUp slopeWeldingSlope downFinal currentPost-flowRemotecontrolPower sourceTungstenelectrodeNozzleInert atmosphereArcWelding directionFillermetalrodMoltenpoolWELDINGEQUIPMENTtGTAW glossaryPreflowShielding gas flows through the torchand gas hoses to push the air outprior to strike an arc.Initial currentAfter the arc is established, a lowerwelding current is applied to pre-heatthe part.Up SlopeWelding current gradually increaseuntil it reaches the preset weldingcurrent.Slope downWelding current progressivelydecreases to the final current valuewhile the travel motion is stopped.This operation allows filling the craterat the end of the weld and preventscracking, particularly on light alloys.Final currentUsed for position welding to solidifythe metal pool.Post-flowShielding gas flow continues to flowfor a short time after the weld currentstops to assure shield gas coverageof the weld zone and of the tungstenelectrode until it is cool.BalanceIn AC mode, time percentage withineach cycle during which the machineis outputting positive or negativecurrent flow. This control is used toadjust weld penetration and arccleaning action.Pulsed weldingWith this mode, welding current ispulsed to better control the moltenmetal pool fluidity and thus get morecontrol on the bead appearance,particularly in position welding.TackingMake a small welds or used totemporarily hold together components ofan assembly until they can be welded.Typical GTAW welding parametersStainless steel - Butt joint configuration - Standard settings, must be tested to comply with your specificationsTUNGSTEN ELECTRODE FILLER METAL GAS FLOWMATERIAL THICKNESS DIAMETERCUP DIAMETERDIAMETER POLARITYAMPERAGE RANGE RECOMMENDEDRATEWELDING SPEEDmm (in)mm (in)mm (in)AGASl/min (CFH)cm/min (in/min)6.4 - 9.51.6 mm (16 ga) 1.6 (1/16) (1/4 - 3/8) 1.6 (1/16) DCEN 50 - 80 Argon 5 (11) 28 (11)6.4 - 9.52.4 mm (3/32") 1.6 (1/16) (1/4 - 3/8) 1.6 (1/16) DCEN 80 - 110 Argon 5 (11) 30 (12)6.4 - 9.53.2 mm (1/8") 1.6 (1/16) (1/4 - 3/8)3.2 (1/8) DCEN 85 - 120 Argon 5 (11) 30 (12)6.4 - 9.54.8 mm (3/16") 2.4 (3/32) (1/4 - 3/8)3.2 (1/8) DCEN 125 - 200 Argon 6 (13) 25 (10)6.4 mm (1/4") 3.2 (1/8) 12.7 (1/2)4.8 (3/16) DCEN 225 - 300 Argon 6 (13) Requires one or two passes12.7 mm (1/2") 4.8 (3/16) 12.7 (1/2)6.4 (1/4) DCEN 300 - 400 ArgonRequires one or two passesC-22www.airliquide.ca1-800-817-7697C-23

GTAW Welding Equipment (TIG)GTAW Welding Equipment (TIG)Lincoln Precision TIG ® 225InputOutput0.3 - 4.8 mm (28# - 3/16")Input Output 0.3 - 4.8 mm (28# - 3/16")Lincoln Precision TIG ® 275WELDINGEQUIPMENTwith Ready-Pak ® PackagePART NUMBERLIN-K25351Input Amperage39 A / 230 V @ Rated OutputAmperage RangeAC 5 - 230 ADC 5 - 230 ARated Output 90 A / 23.4 V / 100%Maximum OCV75 VDimensions (H x W x D) 526 x 368 x 650 mm (20.7 x 14.5 x 25.6 in)Net Weight96 kg (212 lb)IncludesLincoln Precision TIG 225 welding machine, 3 m (10 ft) work cable and clamp, TIGprocedure guide, GTAW (TIG) handbook, PTA-17 torch with 3.6 m (12 ft) cable,2.4 mm (3/32") 2% thoriated tungsten electrode, collet and collet body, gas regulatorand hose, foot Amptrol ® .PART NUMBERLIN-K26181Input Amperage72 A / 230 V @ Rated OutputAmperage RangeAC 2 - 340 ADC 2 - 340 ARated Output 275 A / 21 V / 40%Maximum OCV75 VDimensions (H x W x D) 787 x 559 x 660 mm (31 x 22 x 26 in)Net Weight180 kg (397 lb)IncludesLincoln Precision TIG 275 welding machine, Under-Cooler cart water cooler, footAmptrol(R), gas regulator and hose, PTW-20 Pro-Torch 250 A TIG torch with7.6 m (25 ft) cable, zippered torch cover, parts kit, water hose (2 included),4.5 m (15 ft) 2/0 work cable and clamp, adapter for optional PTA-9 or17 torch 10 mm (3/8")with Ready-Pak ® PackageWELDINGEQUIPMENTLincoln Precision TIG® 225 without Ready-Pak®: LIN-K25331OPTIONAL ACCESSORIESUnderstorage CartLIN-K23481Medium Canvas CoverLIN-K237813M Speedglas 9002X3MC-040011231BLUESHIELD 630-308L 1.6 mm (1/16") Rods BLU-10340816ALTIG Shielding GasGAS-ALTIG16ELECTRODE DIAMETER 1 mm (0.040") 1.6 mm (1/16") 2.4 mm (3/32")Collet LIN-KP20302B1 LIN-KP20303B1 LIN-KP20304B1Collet Body LIN-KP20322B1 LIN-KP20323B1 LIN-KP20324B1Tungsten Electrodes (10) BLU-25751702 BLU-25751704 BLU-25751706Back Cap LIN-KP20361B1 LIN-KP20361B1 LIN-KP20361B1Parts KitLIN-KP508NOZZLE I.D. 6 mm (1/4") 8 mm (5/16") 10 mm (3/8")Alumina Nozzle LIN-KP20166B1 LIN-KP20165B1 LIN-KP20164B1ELECTRODE DIAMETER 1.6 mm (1/16") 2.4 mm (3/32") 3.2 mm (1/8")Collet LIN-KP20293B1 LIN-KP20294B1 LIN-KP20295B1Collet Body LIN-KP20313B1 LIN-KP20314B1 LIN-KP20315B1Tungsten Electrodes (10) BLU-25751704 BLU-25751706 BLU-25751708Back Cap LIN-KP20354B1 LIN-KP20354B1 LIN-KP20354B1Parts KitLIN-KP510NOZZLE I.D. 8 mm (5/16") 10 mm (3/8") 11 mm (7/16")Alumina Nozzle LIN-KP20172B1 LIN-KP20173B1 LIN-KP20174B1Lincoln Precision TIG 275 without Ready-Pak®: LIN-K26191OPTIONAL ACCESSORIESAdvanced Control PanelLIN-K26211Power Factor Correction Kit LIN-K183113M Speedglas 9002X3MC-040011231BLUESHIELD 630-308L 1.6 mm (1/16") Rods BLU-10340816ALTIG Shielding GasGAS-ALTIG16Miller Synchrowave ® 200InputOutput0.3 - 4.8 mm (28# - 3/16")InputOutput0.3 - 12.7 mm (28# - 1/2")Miller Synchrowave ® 250 DXPART NUMBERMIL-907308Input Amperage54 A / 230 V @ Rated OutputAmperage RangeAC 5 - 200 ADC 5 - 200 ARated Output 150 A / 26 V / 40%Maximum OCV80 VDimensions (H x W x D) 765 x 537 x 546 mm (30.1 x 21.1 x 21.5 in)Net Weight108 kg (238 lb)IncludesMiller Synchrowave 200 welding machine, 2.4 m (8 ft) primary cord, gas regulatorand hose, electrode holder with, 150 A TIG torch, RCFS-14 foot control with6 m (20 ft) cord, 3.7 m (12 ft) work cable with clampPART NUMBERMIL-9511118Input Amperage38 A / 575 V @ Rated OutputAmperage RangeAC 3 - 310 ADC 3 - 310 ARated Output 250 A / 30 V / 40%Maximum OCV80 VDimensions (H x W x D) 1168 x 724 x 1029 mm (46 x 28.5 x 40.5 in)Net Weight217 kg (478 lb)IncludesMiller Synchrowave 250DX welding machine, Coolmate 3X cooler, No. 37 runninggear, RCFS-14 foot control, international style connectors, four gallons of TIG coolant,250 A water-cooled TIG torch, cable cover, accessory kit, regulator/flowmeter, gashose, torch adapter, weld lead with clamp and Dinse connector.with Complete PackageOPTIONAL ACCESSORIESNo. 39 Running GearProtective Cover3M Speedglas 9002XBlueshield 630-308L 1.6 mm (1/16") RodsALTIG Shielding GasMIL-300009MIL-3000593MC-040011231BLU-10340816GAS-ALTIG16ELECTRODE DIAMETER 1 mm (0.040") 1.6 mm (1/16") 2.4 mm (3/32")Collet WEL-10N22 WEL-10N23 WEL-10N24Collet Body WEL-10N30 WEL-10N31 WEL-10N32Tungsten Electrodes (10) BLU-25751702 BLU-25751704 BLU-25751706Back Cap WEL-57Y02 WEL-57Y02 WEL-57Y02Parts KitWEL-AK2NOZZLE I.D. 6 mm (1/4") 8 mm (5/16") 10 mm (3/8")Alumina Nozzle WEL-10N50 WEL-10N49 WEL-10N48ELECTRODE DIAMETER 1.6 mm (1/16") 2.4 mm (3/32") 3.2 mm (1/8")Collet WEL-13N22 WEL-13N23 WEL-13N24Collet Body WEL-13N27 WEL-13N28 WEL-13N29Tungsten Electrodes (10) BLU-25751704 BLU-25751706 BLU-25751708Back Cap WEL-41V24 WEL-41V24 WEL-41V24Parts KitWEL-AK4NOZZLE I.D. 8 mm (5/16") 10 mm (3/8") 11 mm (7/16")Alumina Nozzle WEL-13N09 WEL-13N10 WEL-13N11Miller Synchrowave® 250 DX without Complete Package: MIL-907195OPTIONAL ACCESSORIESSequence ModuleMIL-195345Power Factor Correction Kit MIL-1946923M Speedglas 9002X3MC-040011231BLUESHIELD 630-308L 2.4 mm (3/32") Rods BLU-10340824ALTIG Shielding GasGAS-ALTIG16C-24C-25www.airliquide.ca1-800-817-7697

GTAW Welding Equipment (TIG)GTAW Welding Equipment (TIG)Lincoln Invertec ® V205-T AC/DCInputOutput0.3 - 6.4 mm(28# - 1/4")InputOutput0.3 - 12.7 mm(28# - 1/2")Lincoln Invertec ® V310-T AC/DCWELDINGEQUIPMENTwith One-Pak ® PackagePART NUMBERLIN-K23502Input Amperage18 A / 230 V @ Rated OutputAmperage RangeAC 6 - 200 ADC 6 - 200 ARated Output 170 A / 16 V / 60%Maximum OCV53.7 VDimensions (H x W x D) 381 x 216 x 483 mm (15 x 8.5 x 19 in)Net Weight17.3 kg (38 lb)IncludesLincoln Invertec V205-T AC/DC welding machine, PTA-17 torch, parts kit, Harrisflowmeter/regulator, 3 m (10 ft) gas hose, Twist-mate adapter, work clamp and cable,foot Amptrol.PART NUMBERLIN-K26951Input Amperage24.6 A / 230 V / 3-Phase @ Rated OutputAmperage RangeAC 5 - 310 VDC 5 - 310 VRated Output 310 A / 22.4 V / 30%Maximum OCV80 VDimensions (H x W x D) 439 x 269 x 609 mm (17.3 x 10.6 x 24 in)Net Weight34 kg (75 lb)IncludesLincoln Invertec ® V310-T AC/DC, Cool Arc ® 35 water cooler, inverter cart,TIG Mate 20 torch kit, Foot Amptrol ® , Zippered cable coverwith One-Pak ® PackageWELDINGEQUIPMENTLincoln Invertec® V205-T AC/DC without One-Pak®: LIN-K18554OPTIONAL ACCESSORIESSmall Canvas CoverLIN-K23771Welding CartLIN-K227513M Speedglas 9002X3MC-040011231BLUESHIELD 630-308L 1.6 mm (1/16") Rods BLU-10340816ALTIG Shielding GasGAS-ALTIG16ELECTRODE DIAMETER 1 mm (0.040") 1.6 mm (1/16") 2.4 mm (3/32")Collet LIN-KP20302B1 LIN-KP20303B1 LIN-KP20304B1Collet Body LIN-KP20322B1 LIN-KP20323B1 LIN-KP20324B1Tungsten Electrodes (10) BLU-25751702 BLU-25751704 BLU-25751706Back Cap LIN-KP20361B1 LIN-KP20361B1 LIN-KP20361B1Parts KitLIN-KP508NOZZLE I.D. 6 mm (1/4") 8 mm (5/16") 10 mm (3/8")Alumina Nozzle LIN-KP20166B1 LIN-KP20165B1 LIN-KP20164B1ELECTRODE DIAMETER 1.6 mm (1/16") 2.4 mm (3/32") 3.2 mm (1/8")Collet LIN-KP20293B1 LIN-KP20294B1 LIN-KP20295B1Collet Body LIN-KP20313B1 LIN-KP20314B1 LIN-KP20315B1Tungsten Electrodes (10) BLU-25751704 BLU-25751706 BLU-25751708Back Cap LIN-KP20354B1 LIN-KP20354B1 LIN-KP20354B1Parts KitLIN-KP510NOZZLE I.D. 8 mm (5/16") 10 mm (3/8") 11 mm (7/16")Alumina Nozzle LIN-KP20172B1 LIN-KP20173B1 LIN-KP20174B1Lincoln Invertec V310-T AC/DC without One-Pak®: LIN-K22281OPTIONAL ACCESSORIESTiggers Welder Gloves (Large) BLU-047350653M Speedglas 9002X3MC-040011231BLUESHIELD ER70S-3 2.4 mm (3/32) Rods BLU-46601306BLUESHIELD 630-308L 2.4 mm (3/32") Rods BLU-10340824ALTIG Shielding GasGAS-ALTIG16Miller Dynasty ® 200 DXInputOutput0.3 - 6.4 mm (28# - 1/4”)InputOutput0.3 - 12.7 mm (28# - 1/2")Miller Dynasty 350with Contractor KitPART NUMBERS MIL-907099011 DYNASTY® 200DXMIL-195054CONTRACTOR KITInput Amperage15 A / 230 V / 1-Phase @ Rated OutputAmperage RangeAC 1 - 200 ADC 1 - 200 ARated Output 100 A / 24 V / 50%Maximum OCV80 VDimensions (H x W x D) 343 x 121 x 546 mm (13.5 x 7.5 x 21.5 in)Net Weight20.5 kg (45 lb)IncludesMiller Dynasty ® 200DX welding machine, Protective case with carrying handle,DB1725R 7.6 m (25 ft) TIG torch, RFCS-14 HD foot control, International style torchadapters, Regulator/Flowmeter, 200 A Electrode holder with 4.6 m (15 ft) cable,300 A work clamp with 4.6 m (15 ft) cable, 3.6 m (12 ft) gas hose, AK-2 torchaccessory kit, Gas hose coupler.PART NUMBERInput AmperageAmperage RangeRated OutputMaximum OCVDimensions (H x W x D)Net WeightIncludesMIL-95107410 A / 575 V / 3-Phase @ Rated OutputAC 5 - 350 ADC 5 - 350 A300 A / 32 V / 60% (3-Phase)75 V1146 x 587 x 1111 mm (45.1 x 23.1 x 43.75 in)140 kg (308 lb)Miller Dynasty ® 350, RFCS-14 HD foot control, coolmate 3.5 coolant syste, cart,7.6 m (25 ft) Weldcraft CS310 water-cooled torch, torch cable cover, CS310AKC torchaccessory kit, Smith regulator/flowmeter HM2051A-580, 3.7 m (12 ft) rubber gashose, water-cooled Dinse torch adapter, 4.6 m (15 ft) 1/0 weld lead with clamp(work or ground lead) and Dinse connector, 4 gallons of coolantwith Complete PackageOPTIONAL ACCESSORIESMachine CoverWelding Cart3M Speedglas 9002XBLUESHIELD 630-308L 1.6 mm (1/16") RodsALTIG Shielding GasMIL-195322MIL-0425373MC-040011231BLU-10340816GAS-ALTIG16ELECTRODE DIAMETER 1 mm (0.040") 1.6 mm (1/16") 2.4 mm (3/32")Collet WEL-10N22 WEL-10N23 WEL-10N24Collet Body WEL-10N30 WEL-10N31 WEL-10N32Tungsten Electrodes (10) BLU-25751702 BLU-25751704 BLU-25751706Back Cap WEL-57Y02 WEL-57Y02 WEL-57Y02Parts KitWEL-AK2NOZZLE I.D. 6 mm (1/4") 8 mm (5/16") 10 mm (3/8")Alumina Nozzle WEL-10N50 WEL-10N49 WEL-10N48ELECTRODE DIAMETER 1.6 mm (1/16") 2.4 mm (3/32") 3.2 mm (1/8")Collet WEL-13N22 WEL-13N23 WEL-13N24Collet Body WEL-13N27 WEL-13N28 WEL-13N29Tungsten Electrodes (10) BLU-25751704 BLU-25751706 BLU-25751708Back Cap WEL-94 WEL-94 WEL-94Parts KitWEL-CS310UAKNOZZLE I.D. 8 mm (5/16") 10 mm (3/8") 11 mm (7/16")Alumina Nozzle WEL-13N09 WEL-13N10 WEL-13N11Miller Dynasty 350 without Complete package: MIL-907204OPTIONAL ACCESSORIESTiggers Welder Gloves (Large) BLU-047350653M Speedglas 9002X3MC-040011231BLUESHIELD ER70S-3 2.4 mm (3/32) Rods BLU-46601306BLUESHIELD 630-308L 2.4 mm (3/32") Rods BLU-10340824ALTIG Shielding GasGAS-ALTIG16C-26C-27www.airliquide.ca1-800-817-7697

▼GTAW Welding Equipment (TIG)GTAW Welding Equipment (TIG)Suggested Tungsten Preparation1. Preparing Tungsten for DC Electrode Negative (DCEN) Welding or AC Welding with Inverter Machines22 1/2 Times ElectrodeDiameter▼3RadialGrinding CausesWandering Arc1 Grinding WheelGrind end of tungsten on fine grit, hard abrasive wheel beforewelding. Do not use wheel for other jobs or tungsten can becomecontaminated causing lower weld quality.12Tungsten Electrode3Flat4Ideal Tungsten Preparation - Stable ArcWrongTungstenPreparation4Diameter of this flat determines amperage capacity.Straight GroundGrind lengthwise, not radial.2. Preparing Tungsten for AC Sine Wave & Conventional Squarewave121Tungsten Electrode▼▼1 - 1 1/2 Times Electrode Diameter2 Balled EndBall end of tungsten by applying AC amperage recommended for a given electrode diameter.Let ball on end of the tungsten take its own shape.WELDINGMACHINESTypical Current Ranges for Tungsten Electrodes*ELECTRODEDIAMETERmm (in)DIRECT CURRENT (A)ALTERNATING CURRENT (A)DC – DC + ADVANCED SQUAREWAVE SQUAREWAVEALL TUNGSTEN EXCEPT PUREPURE TUNGSTENALL TUNGSTENEXCEPT PUREPURE TUNGSTENALL TUNGSTENEXCEPT PUREWELDINGMACHINES1.0 (0.040) 15 - 18 N/A 20 - 60 15 - 80 10 - 30 20 - 601.6 (0.060) 70 - 150 10 - 20 50 - 100 70 - 150 30 - 80 60 - 1202.4 (0.093) 150 - 250 15 - 30 100 - 160 140 - 235 60 - 130 100 - 1803.2 (1/8) 250 - 400 25 - 40 150 - 200 225 - 325 100 - 180 160 - 2504.0 (5/32) 400 - 500 40 - 55 200 - 275 300 - 400 160 - 240 200 - 3204.7 (3/16) 500 - 750 55 - 80 250 - 350 400 - 500 190 - 300 290 - 390* EWP: Pure tungstenEWX-X: All other tungsten (except Pure)Based on the use of Argon as a shielding gas. Other current values may be employed depending on the shielding gas, type of equipment, and application.Air Liquide recommendsthe use of argon andALTIG shielding gasesfor your GTAW applications.C-28www.airliquide.ca1-800-817-7697C-29

GTAW Welding Equipment (TIG)GTAW Welding Equipment (TIG)WELDINGMACHINESWELDINGMACHINES*See accessory section in this catalogue for further information.C-30www.airliquide.ca1-800-817-7697C-31

SMAW Welding Equipment (Stick)SMAW Welding Equipment (Stick)Typical stick welding installationAC or DCpower source(single orthree-phasesupply)Primary cablePower sourceHelmetBlueshield Mild-Steel ElectrodesNAMEAWS CSA/CWBDIAMETERPACKAGINGPOSITION TYPE APPLICATIONCLASS CLASS mm in kg lbAllLA 6010 E6010 E4310 (VerticalDown)CellulosicDC+Forceful and penetrating arcfor structural steel, pipe,boiler and pressure vessels.ITEM NUMBER2.5 3/32 4 x 2.5 4 x 5.5 BLU-309711063.2 1/8 BLU-309711084.0 5/32 4 x 5 4 x 11 BLU-309711105.0 3/16 BLU-309711122.5 3/32 4 x 2.5 4 x 5.5 BLU-30970106WELDINGEQUIPMENTStick electrodeWorkpieceLA ULTRA 11 E6011 E4311 AllLA 6013 E6013 E4313 AllMaintenance and repair workCellulosic 3.2 1/8 BLU-30970108on dirty or rusty material.AC/DC+ 4.0 5/32BLU-30970110Ship and farm repair.4 x 5 4 x 115.0 3/16 BLU-309701126.0 1/4 BLU-30970116*RutileAC/DC-/+General purpose.Thinner gauge materialsvertically down. Fastfreezing, used to bridge gaps.2.5 3/32 4 x 2.5 4 x 5.5 BLU-309713063.2 1/8 BLU-309713084.0 5/32 4 x 5 4 x 11 BLU-309713105.0 3/16 BLU-30971312WELDINGEQUIPMENTStick electrode welding metal transferSecondary cablesAmperage settingGround clampLA 7014 E7014 E4914 AllRutileAC/DC-/+General purpose,high-speed, iron powderelectrodes. Ornamental ironsheet metal “farmer’s rod”.2.5 3/32 4 x 2.5 4 x 5.5 BLU-309714063.2 1/8 BLU-309714084.0 5/32 4 x 5 4 x 11 BLU-309714105.0 3/16 BLU-30971412Weld beadpenetrationSlagMetallic coreCraterProtectionatmosphereWorkpiece Weld bead Molten poolCoatingMetaldropletsTHICKNESSES FOR DOWNHANDELECTRODE TYPICAL WELDINGWELDING, BUTT WELDING ANDDIAMETERCURRENTFILLET WELDINGmm in mm in (A)1.6 1/16 1.6 1/16 402.0 5/64 2.0 5/64 552.0 – 3.0 5/64 – 0.12 2.5 3/32 703.0 – 5.0 0.12 – 0.20 3.2 1/8 1103.0 – 10.0 0.12 – 0.40 4.0 5/32 160> 8.0 > 5/16 5.0 3/16 200> 10.0 > 0.40 6.3 1/4 290LA 7018 E7018-1 E4918-1-H4 AllLA 7024 E7024 E4924BasicDC+/ACLA 7018 is an industrystandard Code quality7018-1 with impact valuesdown to -46ºC (-50ºF).Structural steels,boilers and pressure vessels.2.5 3/32 4 x 2.5 4 x 5.5 BLU-329717063.2 1/8 BLU-329717084.0 5/32 BLU-329717104.0 5/32 4 x 5 4 x 11 BLU-32971711*5.0 3/16 BLU-329717126.0 1/4 BLU-329717162.5 3/32 4 x 2.5 4 x 5.5 BLU-30972406General-purpose, high-speed,3.2 1/8BLU-30972408heavily-coated iron4 x 5 4 x 11Flat and Rutile 4.0 5/32 BLU-30972410powder electrodes.horizontal AC/DC-Storage tank. Sheet plate and4.0 5/32 BLU-30972411*structural-metal work.5.0 3/16 4 x 4.5 4 x 10 BLU-30972412*6.0 1/4 BLU-30972416*Mild-steel electrode length: 2.5 mm = 300 mm (12”)3.2 mm, 4.0 mm, 5.0 mm = 350 mm (14”)6.0 mm = 450 mm (18”)* Electrode length = 450 mm (18”)NOTE: Blueshield electrodes may meet code requirements other than those listed.Please consult a representative for a complete listing of the code requirements for our electrodes.Duty Cycle(As defined by EN 60 974-1 standard)Test cycle length: 10 min. / Room temperature: 40 o CExample: 250 A at 60% means that, with a stabilized cycle andtemperature, the power source will be able to deliver the ratedcurrent value during 6 minutes and that it have to stay idle for4 minutes before a new cycle is started (at a room temperatureof 40 o C).T °COvertemperatureShut-down circuit point SF-T6 MINUTES 4 MINUTES 6 MINUTES 4 MINUTES 6 MINUTES 4 MINUTESTIMEAt a duty cycle of 100%, the power source can permanentlydeliver the rated current at a room temperature of 40 o C.C-32www.airliquide.ca1-800-817-7697C-33

SMAW Welding Equipment (Stick)SMAW Welding Equipment (Stick)Lincoln Invertec V-155 SInputOutputInputOutputAir Liquide A 230 AC/DCwith Ready-Pak ® packageThe NEW Invertec ® V155-S offers much more than you would expect from a welder this size.Weighing in at just under 15 lb. (6.8 kg) the Invertec ® V155-S is no lightweight contender. It packsthe full punch of a heavyweight professional that you can take to the most demanding job sites.With 120/230V auto reconnect operation, the Invertec ® V155-S can operate from a portablegenerator. It can also plug into a 200 foot (61 m) 230V extension cord so you can weld just aboutanywhere. The tough dent resistant case is IP23 rated for outdoor use.The A 230 AC/DC from Air Liquide Welding is a rugged performer for manual stick welding.A standard running gear improves mobility and assists the operator in positioning the equipmentfor those hard-to-reach areas.Standard Dinse connections increase the versatility of the equipment and make welding cablereplacement/extensions an easy task.Infinite current regulation allows precise setting of amperage to achieve the exact heat for yourwelding needs.WELDINGEQUIPMENTLincoln Invertec® V-150 S without Ready-Pak®:LIN-K26051PART NUMBERInput AmperageAmperage RangeRated OutputMaximum OCVDimensions (H x W x D)Net WeightIncludesLIN-2606131 A / 230 V @ Rated Output5 - 155 ASTICK 145 A / 25.8 V / 30% (230 V Input)TIG 130 A / 15.2 V / 30% (230 V Input)75 V288 x 158 x 392 mm (11.3 x 6.2 x 15.4 in)6.7 kg (14.7 lb)Invertec ® V155-S, stick electrode holder and 3 m (10 ft) cable with Twist-Mateplug, work clamp and 3 m (10 ft) cable with Twist-Mate plug, shoulder strap,2 m (6.6 ft) 120/230V input cord with a 120V 15 A plug, extra 120V 20 A plug,gas regulator, PTA-17V TIG torch with Ultraflex cable and Twist-Mate adapter,PTA-17 TIG accessory kit (LIN-KP508), easy-store/easy-carry suitcasePART NUMBERInput AmperageAmperage RangeRated OutputMaximum OCVDimensions (H x W x D)Net WeightIncludesALW-M11050051230 A / 230 V @ Rated OutputAC 50 - 260 ADC 30 - 170 A160 A / 26 V / 20% (DC mode)80 V (DC mode)460 x 790 x 530 mm (24 x 18 x 36 in)45 kg (100 lb)A 230 AC/DC power source with 2.43 m (8 ft) power cord, handle and running gear,electrode holder wih 3.66 m (12 ft) cable and 50 mm Dinse ® connector, 3 m (10 ft)work cable with clamp and 50 mm Dinse ® connectorWELDINGEQUIPMENTMiller Maxstar 150 SInputOutputInputOutputAir Liquide A 250 AC/DCwith carrying caseBest in class - provides maximum portability and performance in the most compact Stickpackage in the industry. Packs dependability and performance all in one machine.New! Miller's exclusive multi-voltage plug (MVP) allows connection to 115 or 230 V receptacleswithout tools - choose the plug that fits the receptacle and connect it to the power cord.Portable in the shop or at the job site - at 13.2 lb the shoulder strap allows the operator to easilymove from location to location.Auto-Line circuitry automatically connects to 115 - 230 VAC, single-phase power withoutremoving the cover to relink the powerThe new A 250 AC/DC from Air Liquide Welding sets a new standard for AC/DC arc weldingmachines. This ruggedly built welder is a proven performer with serious amperage to burn2.5 mm (3/32 in) to 4.0 mm (5/32 in) low-hydrogen and special-alloy electrodes. A standardrunning gear improves mobility and assists the operator in positioning the equipment for thosehard-to-reach areas. Standard Dinse connections increase the versatility of the equipment andmake welding cable replacement an easy task.The 230 / 460 / 575 volt, 1-phase input power gives operators the option of choosing the powerconnections that are right for them.PART NUMBERInput AmperageAmperage RangeRated OutputMaximum OCVDimensions (H x W x D)Net WeightIncludesMIL-90713401221.6 A / 230 V @ Rated Output20 - 150 ASTICK 150 A / 26 V / 30% (230 V Input)TIG 150 A / 26 V / 30% (115 and 230 V Input)75 V229 x 140 x 337 mm (9 x 5.5 x 13.2 in)6 kg (13.2 lb)Miller Maxstar 150 S power source with cord, stick electrode holder with4 m (13 ft) cable, 3 m (10 ft) work cable with clamp, shoulder strap amdcarrying case.PART NUMBERInput AmperageAmperage RangeRated OutputMaximum OCVDimensions (H x W x D)Net WeightIncludesALW-11050042628 A / 575 V @ Rated OutputAC 40 - 250 ADC 25 - 180 A180 A / 27 V / 30% (DC mode)79 V (DC mode)610 x 580 x 985 mm (24 x 23 x 39 in)80 kg (176 lb)A 250 AC/DC power source, handle and running gearMiller Maxstar 150 S without carrying case: MIL- 907134C-34C-35www.airliquide.ca1-800-817-7697

SMAW Welding Equipment (Stick)SMAW Welding Equipment (Stick)Lincoln Invertec V-275 SInputOutputInputOutputMiller Goldstar 452WELDINGEQUIPMENTThe Invertec ® V275-S power source is ideal for the rigors of the construction site. IP23S ratedand equipped with weather resistant features, this Stick and TIG power source is designed foroutdoor use. Up to 275 amps of output gives you access to a greater number of stick electrodes,and outstanding 6010 performance. The Invertec ® V275-S is available as a single unit or mountedin 4-pack or 8-pack racks for convenience on the construction site. Standard features such asselectable Hot Start and adjustable Arc Force provide a level of arc control you won’t findanywhere else in this class of machine.PART NUMBERInput AmperageAmperage RangeRated OutputMaximum OCVDimensions (H x W x D)Net WeightLIN-K2269114 A / 575 V / 3-Phase @ Rated Output5 - 275 A250 A / 30 V / 60% (575 V / 3-Phase Input)80 V345 x 229 x 514 mm (13.6 x 9 x 20.25 in)29.7 kg (54.5 lb)From steel erection to shipbuilding, from foundries to refineries, the Gold Star Series from Miller isknown by welders the world over for rugged, reliable performance and superior arc characteristics.Built-in arc control for Stick welding allows operators more flexibility when welding in tight areaswhere sticking electrodes is a problem.Hot Start makes it easy to start difficult electrodes.Simple control panel provides easy, efficient operation.Unique Fan-On-Demand operates only when needed reducing noise, power consumption, andthe amount of airborne contaminants pulled through the machine.PART NUMBERMIL-903400Input Amperage36 A / 575 V @ Rated OutputAmperage Range20 - 590 ARated Output 450 A / 38 V / 60%Maximum OCV72 VDimensions (H x W x D) 762 x 585 x 966 mm (30 x 23 x 38 in)Net Weight183 kg (404 lb)WELDINGEQUIPMENTIncludesLincoln Invertec V-275 S welding machineIncludesMiller Goldstar 452 welding machineMiller CST 280InputOutputGasoline EngineOutputAir Liquide Welding Wolfpac 175Durable yet lightweight Stick/TIG welding power source designed for construction industry. 280amps of output is ideal for stick electrodes up to 3/16 in and TIG welding pipe and plate.Easy voltage changeover between voltage ranges through a two-position manual switch.Conveniently located on the rear panel, it simplifies voltage change in racks.Simple to operate with a process selector knob which automatically sets the proper dig setting onE6010 and E7018 electrodes providing superior stick performance.Lift-Arc start provides arc starting without the use of high frequency.Fan-On-Demand cooling system operates only when needed providing noise reduction.PART NUMBERInput AmperageAmperage RangeRated OutputMaximum OCVDimensions (H x W x D)Net WeightIncludesMIL-90724414.7 A / 575 V / 3-Phase @ Rated Output5 - 280 A280 A / 31.2 V / 35% (3-Phase)77 V343 x 191 x 457 mm (13.5 x 7.5 x 18 in)18.6 kg (41 lb)Miller CST 280 power source with 2 m (6 ft) power cordWelders depend on the WOLFPAC 175 for quality weld output and consistent auxiliary power.The WOLFPAC 175 is an engine-driven welding generator with excellent performance for stickand scratch start TIG welding. The heavy -duty design provides 60% duty cycle at 170 A with40-170 A weld output and delivers the highest available auxiliary power while welding. This uniquegenerator delivers a smooth weld output. Its brushless design increases efficiency, reducesmaintenance and extends the life of the machine. Separate windings are used for weldingand auxiliary power, offering the highest quality auxiliary power. A rugged 1-cylinder, gas-fueled,air-cooled Honda engine powers the generator. The heavy-duty roll case design is standard,along with high frequency protection, muffler, low oil pressure shutdown and engine hour meter.PART NUMBERALW-MU111017EngineHonda GX270 OHV, 1-cylinder, 4-cycle, air-cooledAmperage Range40 - 170 ARated Output 170 A / 60%Maximum OCV90 VAuxiliary Power115 V, 60 Hz, 1-Phase, 2 kVA230 V, 60 Hz, 1-Phase, 4 kVAGas Tank6 l (1.6 gal US)Dimensions (H x W x D) 343 x 191 x 457 mm (13.5 x 7.5 x 18 in)Net Weight18.6 kg (41 lb)IncludesC-36C-37www.airliquide.ca1-800-817-7697

Engine-Driven Welding EquipmentEngine-Driven Welding EquipmentLincoln Ranger 250Gasoline EngineOutputGasoline EngineOutput0.8 - 4.8 mm (22# - 1/2")Lincoln Ranger 305Gwith Kohler engineThe Ranger ® 250 is ready for a workout – all day, everyday! Intended for contractors, constructionand maintenance applications, this tough Lincoln gasoline-driven welder/generator delivers 250 Afor welding at 100% duty cycle. The Ranger ® 250 is recommended for stick welding, including aseparate, dedicated downhill pipe mode, as well as DC Touch-Start TIG ® , flux-cored and MIG wirewelding and arc gouging. Lincoln Chopper Technology provides easy starts, an extremelysmooth arc, low spatter and outstanding bead appearance. The sleek, enclosed case lowersnoise and protects critical engine components. Hot looks, hot features, hot performance – That’sthe Ranger ® 250!The Ranger ® 305G is a powerful stick, TIG, wire and pipe welding engine driven welder that isready for all day, everyday performance. Rugged and dependable, the Ranger ® 305G is built witha totally enclosed case for maximum protection; Lincoln’s Chopper Technology for an arcoperators appreciate; and a 12-gallon fuel tank that will last you through the entire day. Lincoln’sRanger ® 305G ... it’s ready for a workout.with One-Pak ® PackageWELDINGEQUIPMENTPART NUMBEREngineAmperage RangeRated OutputMaximum OCVAuxiliary PowerGas TankDimensions (H x W x D)Net WeightIncludesLIN-K172510Kohler OHV Command CH23S, 2-cylinder, 4-cycle, air-cooled20 - 250 A250 A / 28 V / 100% (DC, CV or CC)80 V115 V, 60 Hz, 1-Phase, 9.5 kVA230 V, 60 Hz, 1-Phase, 9.5 kVA45 l (12 gal US)920 x 546 x 1073 mm (36.2 x 21.5 x 42.3 in)227 kg (500 lb)Lincoln Ranger 250 welding machine with mechanical fuel pumpPART NUMBEREngineAmperage RangeRated OutputMaximum OCVAuxiliary PowerGas TankDimensions (H x W x D)Net WeightIncludesLIN-K23532Kohler OHV Command CH23S, 2-cylinder, 4-cycle, air-cooled20 - 305 A (CC / DC)305 A / 29 V / 100% (CC / DC)80 V115 V, 60 Hz, 1-Phase, 9.5 kVA230 V, 60 Hz, 1-Phase, 9.5 kVA45 l (12 gal US)920 x 546 x 1073 mm (36.2 x 21.5 x 42.3 in)227 kg (500 lb)Lincoln Ranger 305G welding machine with mechanical fuel pump,accessory Kit, LN-25 wire feeder, gun and cable, drive roll Kit, 1.8 mm (0.072”)NR-232 11.3 kg (25 lb) spoolWELDINGEQUIPMENTWithout One-Pak package: LIN-K17264Miller Bobcat 250Gasoline Engine Output Gasoline Engine OutputMiller Trailblazer 302with Kohler engineThis high weld output engine drive is the standard for stick and FCAW welding! The ruggedBobcat 250 has the power and key features that help you turn a profit. More horsepower - 23 HPKohler provides more power for demanding weld and generator loads. More guts, more glory!New! Meter maintenance displays. Hour meter function and oil change interval.Quietest engine drive in its class. Fully enclosed case protects the engine and decreases soundlevels by 1/3 over previous models. Removable service doors provide easy access for enginemaintenance.11,000 watts of Accu-Rated - not Inflated generator power.Designed for the professional welder who needs a welder/generator with excellent arcperformance for all types of welding jobs.New! Quietest engine drive in its class. Fully enclosed case protects the engine and decreasessound levels by 1/3 over previous models. Removable service doors provide easy access forengine maintenance.11,000 watts of Accu-Rated - not Inflated generator power. Cranks out enough power for mostapplications: job site, farm/ranch, or home. 9,500 watts of continuous power.with Kohler enginePART NUMBERMIL-907211013EngineKohler CH23, 2-cylinder, 4-cycle, air-cooledAmperage Range40 - 240 ARated Output 250 A / 28 V / 60%Maximum OCV80 VAuxiliary Power115 V, 60 Hz, 1-Phase, 9.5 kVA230 V, 60 Hz, 1-Phase, 9.5 kVAGas Tank45 l (12 gal US)Dimensions (H x W x D) 838 x 508 x 1156 mm (33 x 20 x 45.5 in)Net Weight252 kg (556 lb)IncludesMiller Bobcat 250 welding machine with mechanical fuel pumpPART NUMBEREngineAmperage RangeRated OutputMaximum OCVAuxiliary PowerGas TankDimensions (H x W x D)Net WeightIncludesMIL-907216011Kohler CH23, 2-cylinder, 4-cycle, air-cooled25 - 300 A (CC / DC)280 A / 100% (CC/DC)60 V115 V, 60 Hz, 1-Phase, 9.5 kVA230 V, 60 Hz, 1-Phase, 9.5 kVA45 l (12 gal US)870 x 508 x 1321 mm (34.2 x 20 x 52 in)327 kg (720 lb)Miller Trailblazer 302 (Kohler engine) welding machine with mechanical fuel pumpC-38C-39www.airliquide.ca1-800-817-7697

Engine-Driven Welding EquipmentRobotic SystemsLincoln Vantage ® 300with One-Pak ® packageDiesel EngineOutputThe Vantage ® 300 is an ideal choice for construction teams, pipe rig owners and rental fleetmanagers. Housed in a compact, corrosion resistant stainless steel case, this ruggedwelder/generator features Lincoln Chopper Technology to deliver great arc starts and a smootharc for stick, TIG or wire welding. The quiet, smooth-running 1800 rpm water-cooled 4 cylinderKubota ® diesel engine generates 12,500 watts of 3-phase or 11,500 watts of 1-phase auxiliarypower. And, it’s loaded with convenience features you’ll wish you had on your last welder! It alladds up-top arc performance, a smooth reliable engine, plenty of auxiliary power,compact case and tough materials that are built to last!NUTECH Integro Arc and IntegroTwin-Arc Robotic SystemsFEATURESMachine layout consists of a single on twin roboticweld cell utilizing an ABB welding robot and MIGwelding equipment. Some highlights are:WELDINGEQUIPMENTPART NUMBERLIN-K24523EngineKubota V1505, 4-cylinder, 4-cycle, water-cooledAmperage Range30 - 400 A (DC mode)Rated Output 300 A / 32 V / 100%Maximum OCV90 VAuxiliary Power115 V, 60 Hz, 1-Phase, 10 kVA230 V, 60 Hz, 3-Phase, 11 kVAGas Tank57 l (15 gal US)- Fully enclosed and compact design- Quick-Change Tooling- Integrated base for easy setup & transportOPTIONSWELDINGEQUIPMENTWithout One-Pak package: LIN-K24092Dimensions (H x W x D)Net WeightIncludes913 x 642 x 1524 mm (35.9 x 25.3 x 60 in)469 kg (1035 lb)Lincoln Vantage ® 300, medium welder trailer , Duo-Hitch 50 mm (2") ball/lunetteeye hitch (included), Fender and light kit, cable rack, two cable connectors, two 15.3 m(50 ft) 2/0 electrode cables, 3 m (10 ft) 2/0 electrode cable, 15.3 m (50 ft) 2/0 workcable, 300A Electrode Holder, 300A work clamp- Motoman UP20 or ABB IRB2400L.- Servo headstocks/tailstocks- Allen Bradley or Siemens PLC- Allen Bradley Panel View 1000- TOPTIG robotized TIG welding systemMiller Pro 300 CC/CVwith Caterpillar engineDiesel EngineOutputLow speed, compact diesel welder ideal for the construction contractor, independent rig owner orfleet manager.Compact and lightweight - designed to be the smallest, lightest 1800 rpm low-speed diesel welder.Easy to transport from one job to another.Improved arc performance and stability offer exceptional arc control for stick, MIG and TIGwelding. Stick arc designed for cross-country pipeliners.Four preset DIG settings (stick welding).TOPTIG process innovationTOPTIG process is a major innovation in the world of robotized welding.Developed in the Air Liquide Welding research centre, TOPTIG is a new process development from arcwelding classical solutions. This new process can be used effectively on carbon or stainless steel platesup to 3 mm (0.12 in) as well as on Titanium or Nickel alloys or on galvanized sheets with weld brazing.PART NUMBEREngineMIL-907144Caterpillar C1.5, 3-cylinder, 4-cycle, water-cooledTOPTIG innovative process principleAmperage Range20 - 410 A (CC mode)Rated Output 300 A / 32 V / 60%Maximum OCV65 VAuxiliary Power115 V, 60 Hz, 1-Phase, 10 kVA230 V, 60 Hz, 1-Phase, 10 kVAGas Tank43.5 l (11.4 gal US)Dimensions (H x W x D) 813 x 667 x 1422 mm (32 x 26.2 x 56 in)Net Weight327 kg (720 lb)IncludesMiller Pro 300 welding machine with Caterpillar engineThe filler metal is fed through the nozzle directly into the arcwith an angle of 20 º to the electrode, precisely where thetemperatures are the highest. This concept guarantees a highdeposition rate and an efficient metal transfer. Parameteradjustments permits the choice of a liquid bridge transfer ordroplet transfer mode. In addition the wire speed can be pulsedand synchronized with the current, giving a waved weld beadappearance. Whatever the parameters selected, due to theprecise control of energy, the TOPTIG process guarantees a TIGquality result with a complete absence of spatter and avoidsdistortion on thin metal sheet.C-40C-41www.airliquide.ca1-800-817-7697

Automated plasma weldingPlasma Cutting EquipmentWELDINGEQUIPMENTThe automated plasma welding process, which has been used for several decades by alarge number of manufacturing companies worldwide, allows users to make very significantquality and productivity gains in different types of fabrication.Although it is adaptable to many different welding applications,such as pipe welding, the keyhole plasma welding process hasproven its benefits in terms of productivity enhancement for thefollowing types of vessel manufacturing:- Stainless and carbon steel and titanium base material.- 3 – 10 mm (0.118” – 0.394”) wall thicknessThese types of vessels are widely used in the petrochemical,textile, transportation, food and beverage industries.The main productivity gain is found in the fact the process workson a square edge butt joint (within specified thickness range),so multiple filling passes are not necessary. The automatednature of this process and the low-profile bead shape also reducepost-weld operations, such as grinding.The weld bead quality is above expectations; the keyhole plasmawelding process outclasses other welding processes since itguarantees full penetration welds.Please contact your local Air Liquide representative for moreinformation on these systems.How Plasma Cuts Through MetalThe plasma cutting process, as used in the cutting of electricallyconductive metals, utilizes this electrically conductive gas totransfer energy from an electrical power source through a plasmacutting torch to the material being cut.The basic plasma arc cutting system consists of a power supply,an arc starting circuit and a torch. These system componentsprovide the electrical energy, ionization capability and processcontrol that is necessary to produce high quality, highly productivecuts on a variety of different materials.The power supply is a constant current DC power source. Theopen circuit voltage is typically in the range of 240 to 400 VDC.The output current (amperage) of the power supply determines thespeed and cut thickness capability of the system. The mainfunction of the power supply is to provide the correct energy tomaintain the plasma arc after ionization.The arc starting circuit is a high frequency generator circuit thatproduces an AC voltage of 5,000 to 10,000 volts at approximately2 megahertz. This voltage is used to create a high intensity arcinside the torch to ionize the gas, thereby producing the plasma.The Torch serves as the holder for the consumable nozzle andelectrode, and provides cooling (either gas or water) to these parts.The nozzle and electrode constrict and maintain the plasma jet.Variations of the Plasma Cutting ProcessElectrodeNozzle(-)WELDINGEQUIPMENTConventional Plasma CuttingThis process generally uses a single gas (usually air or nitrogen)that both cools and produces the plasma. Most of these systemsare rated at under 100 Amps, for cutting materials under 5/8"thick. Primarily used in hand, held applicationsWork Piece(+)Precision Plasma CuttingThis process produces superior cut quality on thinner materials,(less than 1/2") at slower speeds. This improved quality is aresult of using the latest technology to super constrict the arc,dramatically increasing energy density.The slower speeds arerequired to allow the motion device to contour more accurately.This process is for mechanized applications only.(High Flow)Vortex NozzleWorkplaceElectrodePlasmaGasInletPlasmaGasVent(+)ShieldGasInletC-42www.airliquide.ca1-800-817-7697C-43

Plasma Cutting EquipmentPlasma Cutting EquipmentHypertherm Powermax 190cInputOutput3 mm (1/8")Input Output 12 mm (1/2")Hypertherm Powermax 45WELDINGEQUIPMENTPART NUMBERHYP-070783Input Current @ 1.32 kW 32 AMaximum Amperage12 ARated Output 12 A / 110 V / 35%Maximum OCV335 VGas SupplyOn-board compressorDimensions (H x W x D) 400 x 216 x 305 mm (15. 8 x 8.5 x 12 in)Net Weight20.9 kg (46 lb)IncludesHypertherm Powermax 190c ower supply with integrated air compressor, PAC105hand torch with 6 m (20 ft) leads, extra consumables for cutting, 6.1 m (20 ft) workcable with clamp.PART NUMBERHYP-088016Input Current @ 5.95 kW 28 A / 230 VAmperage Range20 - 45 ARated Output 41 A / 132 V / 60%Maximum OCV132 VGas SupplyClean, dry, oil-free air or nitrogenDimensions (H x W x D) 426 x 172 x 348 mm (16.75 x 6.75 x 13.7 in)Net Weight16.8 kg (37 lb)IncludesHypertherm Powermax 45 power supply, T45v hand torch with 6 m (20 ft) leads,extra consumables for cutting and gouging, 6 m (20 ft) work cable with clamp,carry strapWELDINGEQUIPMENTOPTIONAL ACCESSORIESLeather Torch SheathingPlasma Cutting Guide - BasicPlasma Cutting Guide - DeluxeOperator Face ShieldSystem Dust CoverHYP-024548HYP-127102HYP-027668HYP-027103HYP-127097WEAR PARTS Shielded Parts Unshielded partsShield HYP-120884 HYP-120884Retaining Cap, ShieldedHYP-120898Nozzle HYP-120882 HYP-120882Electrode HYP-120881 HYP-120881Swirl Ring HYP-120880 HYP-120880Retaining CapHYP-120883WEAR PARTS Shielded Parts Unshielded Parts Gouging PartsShield HYP-220674 HYP-220675 HYP-220717Retaining Cap HYP-220713 HYP-220713 HYP-220713Nozzle HYP-220671 HYP-220672 HYP-220718Swirl Ring HYP-220670 HYP-220670 HYP-220670Electrode HYP-220669 HYP-220669 HYP-220669Consumable Kit (English)HYP-850490Consumable Kit (French)HYP-850492Powermax 45 with 15.2 m (50 ft) leads: HYP-088017OPTIONAL ACCESSORIESLeather Torch SheathingHYP-024548Hand Gouging Heat Shield HYP-128658Plasma Cutting Guide - Deluxe HYP-027668Air Filtering UnitHYP-128647System Dust CoverHYP-127219Hypertherm Powermax 30InputOutput6 mm (1/4")InputOutput19 mm (3/4")Hypertherm Powermax 1000with Deluxe packagePART NUMBERHYP-088004Input Current @ 2.79 kW 13.5 A / 230 VAmperage Range15 - 30 ARated Output 30 A / 83 V / 50% (230 V)Maximum OCV240 VGas SupplyClean, dry, oil-free air or nitrogenDimensions (H x W x D) 305 x 168 x 356 mm (12 x 6.6 x 14 in)Net Weight9 kg (20 lb)IncludesHypertherm Powermax 30 power supply, T30v hand torch with 6 m (20 ft) leads,extra consumables for cutting, 4.5 m (15 ft) work cable with clamp, 240 V / 20 A plugwith adapter plugs for 120 V / 15 A and 240 V / 20 A circuits, rugged carrying case,enhanced consumable kit, plasma cutting guide, cutting gloves, shoulder strapPART NUMBERInput Current @ 8.4 kWAmperage RangeRated OutputMaximum OCVGas SupplyDimensions (H x W x D)Net WeightIncludesHYP-08317811 A / 575 V / 3-Phase20 - 60 A60 A / 140 V / 50% (575 V / 3-Phase)300 VClean, dry, oil-free air or nitrogen586 x 271 x 498 mm (23.1 x 10.7 x 19.6 in)37 kg (83 lb)Hypertherm Powermax 1000 power supply, T60 hand torch with 7.6 m (25 ft) leads,extra consumables for cutting, 4.5 m (15 ft) work cable with clamp.Powermax 30 without Deluxe package: HYP-088003OPTIONAL ACCESSORIESLeather Torch SheathingHYP-024548Plasma Cutting Guide - Basic HYP-127102Plasma Cutting Guide - Deluxe HYP-027668Air Filtering UnitHYP-128647System Dust CoverHYP-127114WEAR PARTSDeflectorRetaining CapNozzleSwirl RingElectrodeConsumable Kit (English)Consumable Kit (French)HYP-220569HYP-220483HYP-220480HYP-220479HYP-220478HYP-850480HYP-850482WEAR PARTS Shielded Parts Gouging Parts FineCut PartsShield HYP-120930 HYP-120977 HYP-120979Retaining Cap HYP-120928 HYP-120928 HYP-120928Nozzle HYP-120931 HYP-220059 HYP-220329Swirl Ring HYP-120925 HYP-120925 HYP-120925Electrode HYP-120926 HYP-120926 HYP-120926Consumable Kit (English)HYP-850430Consumable Kit (French)HYP-850432Powermax 1000 with 15.2 m (50 ft) leads: HYP-083179Powermax 1000 with 22.9 m (75 ft) leads: HYP-083210OPTIONAL ACCESSORIESLeather Torch SheathingHand Gouging Heat ShieldPlasma Cutting Guide - DeluxeSystem Dust CoverAir Filtering UnitHYP-024548HYP-128658HYP-027668HYP-127099HYP-128647C-44C-45www.airliquide.ca1-800-817-7697

Plasma Cutting EquipmentMechanized Cutting SystemsWELDINGEQUIPMENTHypertherm Powermax 1250Powermax 1250 with 15.2 m (50 ft) leads: HYP-087009Powermax 1250 with 22.9 m (75 ft) leads: HYP-087049OPTIONAL ACCESSORIESLeather Torch SheathingHand Gouging Heat ShieldPlasma Cutting Guide - DeluxeSystem Dust CoverAir Filtering UnitHYP-024548HYP-128658HYP-027668HYP-127099HYP-128647InputPART NUMBERInput Current @ 8.4 kWAmperage RangeRated OutputMaximum OCVGas SupplyDimensions (H x W x D)Net WeightIncludesOutputHYP-08700817 A / 575 V / 3-Phase25 - 80 A80 A / 150 V / 60% (575 V / 3-Phase)300 VClean, dry, oil-free air or nitrogen586 x 271 x 498 mm (23.1 x 10.7 x 19.6 in)44 kg (96.6 lb)22 mm (7/8")Hypertherm Powermax 1250 power supply, T80 hand torch with 7.6 m (25 ft) leads,extra consumables for cutting, 4.5 m (15 ft) work cable with clampWEAR PARTS Shielded Parts Gouging Parts FineCut PartsShield HYP-120929 HYP-120977 HYP-120979Retaining Cap HYP-120928 HYP-120928 HYP-120928Nozzle HYP-120927 HYP-220059 HYP-220329Swirl Ring HYP-120925 HYP-120925 HYP-120925Electrode HYP-120926 HYP-120926 HYP-120926Consumable Kit (English)HYP-850440Consumable Kit (French)HYP-850442Air Liquide has a complete mechanized cutting table programfeaturing a full range of cutting machines, equipped withHypertherm HyPerformance plasma systems and/oroxy-fuel torches, to suit virtually any customer requirement.Through strategic partnerships with Canadian cutting machinemanufacturers we have access to cutting machines from acompact 4' x 4' (1.22 m x 1.22 m) size up to the largest ofmachines for heavy industrial applications.Our offer includes:- Cutting machines of any size- Hypertherm plasma systems – number one in the world- Air Liquide gas supply for plasma and/or oxy-fuel processes- OEM consumable parts for best performance and long life- Complete service and training offerPlease contact your local Air Liquide representative for moreinformation on these systems.WELDINGEQUIPMENTHypertherm Powermax 1650InputOutput32 mm (1-1/4")PART NUMBERInput Current @ 16 kWAmperage RangeRated OutputMaximum OCVGas SupplyDimensions (H x W x D)Net WeightIncludesHYP-05927521 A / 575 V / 3-Phase30 - 100 A100 A / 160 V / 80% (575 V / 3-Phase)300 VClean, dry, oil-free air or nitrogen671 x 427 x 655 mm (26.4 x 16.8 x 25.8 in)61 kg (135 lb)Hypertherm Powermax 1650 power supply, T100 hand torch with 7.6 m (25 ft) leads,extra consumables for cutting, 4.5 m (15 ft) work cable with clampPowermax 1650 with 15.2 m (50 ft) leads: HYP-059276Powermax 1650 with 22.9 m (75 ft) leads: HYP-059301OPTIONAL ACCESSORIESLeather Torch SheathingHand Gouging Heat ShieldPlasma Cutting Guide - DeluxeSystem Dust CoverAir Filtering UnitHYP-024548HYP-128658HYP-027668HYP-127100HYP-128647WEAR PARTS Shielded Parts Gouging Parts FineCut Parts (40 A)Shield HYP-220065 HYP-120977 HYP-120979Retaining Cap HYP-220048 HYP-220048 HYP-120928Nozzle HYP-220011 HYP-220063 HYP-220329Swirl Ring HYP-220051 HYP-220051 HYP-220327Electrode HYP-220037 HYP-220037 HYP-120926Consumable Kit (English)HYP-850440Consumable Kit (French)HYP-850442C-46C-47www.airliquide.ca1-800-817-7697

MIG Welder CartsAir Liquide’s welder carts are designed for a variety of MIG weldingmachines with gas cylinders, welding cables and accessories.Storage capabilities include an angled top shelf for easy accessto power source controls, lower and bottom trays for storagespace, sturdy handle and convenient cable wrap hangers.Carts can also transport inverters and mini-plasma machines.WELDINGEQUIPMENTMET-RV130ALMET-RV130ALREDITEMDESCRIPTIONBASE PLATE DIMENSION HEIGHT WIDTH WEIGHTmm in mm in mm in kg lbCart for welding machines, special compartment andMET-RV130ALshelf for accessories. Includes hook for welding gun,pivoting wheels, handle, robust construction.298 x 445 11 3/4 x 17 1/2 813 32 445 17 1/2 19 42Ideal for ALW M132, M172, Miller Millermatic 140 and 180.Cart for welding machines, special compartment andMET-RV130ALREDshelf for accessories. Includes hook for welding gun, pivotingwheels, handle, robust construction but comes with red paint.298 x 445 11 3/4 x 17 1/2 813 32 445 17 1/2 19 42Ideal for Lincoln Power Mig 140C and 180C.C-48www.airliquide.ca