Basic information on the SURGICAL PROCEDURE - Straumann

More documents

Recommendations

Info

Tapered Effect profile drill after the implant bed has been prepared as for a standard or standard Plus implant, preparation concludes with shaping the conical region of the implant bed with a special tapered effect profile drill (max. 300 rpm). there is a profile drill (in two shaft lengths, short or long) corresponding to the selected apical implant diameter (3.3 mm, 4.1 mm, 4.8 mm) (see te profile drills, page 29). the profile drill acts as a depth gauge aid at the same time in order to check the vertical position of the implant. By holding it static in the hole after drilling, the probable shoulder position can be checked. see also hints on possible vertical implant positions on page 14. short or long shaft B = implant shoulder level A = sLactive/sLa ® surface margin (lower edge of the notch) cutting edge Guide cylinder TE profile drills max. 300 rpm
Correct fit of the Tapered Effect implant in the bone in the final position, the cylindrical/apical part of the implant ensures primary stability. the conical part of the implant lies next to the bone. correction of the vertical position by reverse rotation (counter-clockwise) should be avoided. this can lead to a reduction in primary stability. Particular features with the Tapered Effect implant p the conical region of the implant bed must be shaped with a special tapered effect profile drill. p in order to avoid any resorption due to pressure on the bone, tapered effect implants should not fill the alveolus completely. (hDD). their primary stability is achieved with the cylindrical part of the implant. p in most cases, central drilling does not follow the axis of the alveolus exactly. it has to be shifted slightly in the palatal or lingual direction in order to obtain a correct implant position. in general, the implant position should not be chosen only on the basis of the available bone. rather, the desired prosthetic result should act as the basis for the decision, even if this necessitates bone augmentation measures*. * This technique should be employed only by dentists who have adequate experience in the use of augmentation procedures. see also DvD “straumann ® Dental implant system-surgery“, art. no. 150.541, “implantation of a tapered effect implant“. Note Tapered Effect implants should only be inserted by dentists who have adequate experience in oral implantology! Drill axis tooth axis
Page 1 and 2: Basic info
Page 3 and 4: contents 1. Straumann ® Dental Imp
Page 5 and 6: Available surfaces: SLActive and SL
Page 7 and 8: p Contraindications p restorations
Page 9 and 10: Prosthetic restoration Notes rn syn
Page 11 and 12: 2. PrinciPLes of treatment PLanninG
Page 13 and 14: Local aspects General local prerequ
Page 15 and 16: 3. treatment PLanninG careful treat
Page 17 and 18: in the examples given here, the mea
Page 19 and 20: Planning aids for determining the v
Page 21 and 22: Planning aids for implant selection
Page 23 and 24: Custom made drilling templates a cu
Page 25 and 26: 4. surGicaL instruments the instrum
Page 27 and 28: Cleaning and care of instruments Ca
Page 29 and 30: Tips on surgical procedure rapid su
Page 31 and 32: p Multi-use profile drill: there ar
Page 33 and 34: p Manual tapping at the top of the
Page 35 and 36: Preparation of the implant bed for
Page 37 and 38: Insertion Standard implant Ø 4.1 m
Page 39: Preparation of the implant bed for
Page 43 and 44: Surgical auxiliary instruments Adap
Page 45 and 46: Implantation procedure SLA ® Openi
Page 47 and 48: p move the implant into final posit
Page 49 and 50: p attach the ratchet (the clockwise
Page 51 and 52: 7. imPLant cLosure after implantati
Page 53 and 54: Immediate restoration of Straumann
Page 55 and 56: Temporary restoration healing caps
Page 57 and 58: 9. aDDitionaL ProDucts Osteotomes p
Page 59 and 60: 10. aDDitionaL information<
Page 61: IMPORTANT NOTES Disclaimer of liabi

Basic information on the SURGICAL PROCEDURE - Straumann

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?