Basic information on the SURGICAL PROCEDURE - Straumann

More documents

Recommendations

Info

Straumann ® Drill Stop – Precise depth control the straumann ® Drill stop provides precise control over drilling depth during implant bed preparation for the placement of straumann ® dental implants. Delivered in sterile sets the drill stops are ready to use. the straumann ® Drill stop is designed for single-patient use only and must be used in conjunction with the single-patient drills specifically designed for them. Implant bed depth 16 mm 14 mm 12 mm 10 mm 8 mm 6 mm Ø 2.2 mm Ø 2.8 mm Ø 3.5 mm Ø 4.2 mm Drill Stop Set for one depth Straumann ® Drill Stop reference chart Short drill Long drill Drill stop type Drill stop type A B C D each straumann ® Drill stop set includes drill stops with the following diameters: Ø 2,2 mm (blue), Ø 2,8 mm (yellow), Ø 3,5 mm (red), Ø 4,2 mm (green). these diameters correspond to the diameters of the straumann ® drills. applying the following reference chart you can specify which drill stop type can be used in preparing the implant bed depth with the short or long drill. Step 1: Determine the implant bed depth (6, 8, 10, 12, 14, 16 mm). Step 2: choose the drill length (short or long). Step 3: match the implant bed depth to the drill stop type as shown in the reference chart. Important straumann ® drill stops are not indicated for: extraction sites, where bone cavity is often wider than the diameter necessary to hold the drill stop. use with drill templates, due to the interference from or with the template. for more <strong>information</strong> of the straumann ® Drill stop please refer to the brochure “straumann ® p p Drill stop: Precise depth control” (art. no. 152.053). A B C D
p Multi-use profile drill: there are two types of profile drills in the straumann ® Dental implant system: p standard Plus profile drill (max. 400 rpm): p Because of the short neck section in implants in the standard Plus Line (1.8 mm), part of the flared neck configuration is inserted in the bone. there is a special profile drill (max. 400 rpm) for the flared preparation of the implant bed (analogous to the neck configuration of the standard Plus implants). Tip In order to make it easier to insert the drill with the next diameter into the bone cavity, the margin of the implant bed can be bevelled slightly. To do so, the corresponding profile drill is inserted into the drill hole. The diameter of this “auxiliary“ drill corresponds to that of the last pilot or twist drill employed. tapered effect profile drill (max. 300 rpm): these widen the implant bed for the upper conical part of the te implants (see also page 37). Art. No. Article for endosteal implant-Ø 044.086 sP Profile drill Ø 2.8 mm for sP Ø 3.3 mm rn 044.088 sP Profile drill Ø 3.5 mm for sP Ø 4.1 mm rn 044.084 sP Profile drill Ø 4.2 mm for sP Ø 4.8 mm Wn All profile drills are available in a short and a long version. Important: Standard Plus Implants Ø 4.8 mm RN are inserted without profile drilling. The profile drills are suitable only for the corresponding implant type! Art. No. Article for endosteal implant-Ø 044.701 te Profile drill Ø 2.8 mm for te Ø 3.3 mm rn 044.705 te Profile drill Ø 3.5 mm for te Ø 4.1 mm rn 044.703 te Profile drill Ø 4.2 mm for te Ø 4.8 mm Wn All profile drills are available in a short and a long version. Important: The profile drills are suitable only for the corresponding implant type! Standard Plus profile drill short or long insertion depth on sLactive/sLa ® surface margin level cutting edge Tapered Effect profile drill insertion depth on implant shoulder level short or long insertion depth on implant shoulder level insertion depth on sLactive/sLa ® surface margin level cutting edge
Page 1 and 2: Basic info
Page 3 and 4: contents 1. Straumann ® Dental Imp
Page 5 and 6: Available surfaces: SLActive and SL
Page 7 and 8: p Contraindications p restorations
Page 9 and 10: Prosthetic restoration Notes rn syn
Page 11 and 12: 2. PrinciPLes of treatment PLanninG
Page 13 and 14: Local aspects General local prerequ
Page 15 and 16: 3. treatment PLanninG careful treat
Page 17 and 18: in the examples given here, the mea
Page 19 and 20: Planning aids for determining the v
Page 21 and 22: Planning aids for implant selection
Page 23 and 24: Custom made drilling templates a cu
Page 25 and 26: 4. surGicaL instruments the instrum
Page 27 and 28: Cleaning and care of instruments Ca
Page 29: Tips on surgical procedure rapid su
Page 33 and 34: p Manual tapping at the top of the
Page 35 and 36: Preparation of the implant bed for
Page 37 and 38: Insertion Standard implant Ø 4.1 m
Page 39 and 40: Preparation of the implant bed for
Page 41 and 42: Correct fit of the Tapered Effect i
Page 43 and 44: Surgical auxiliary instruments Adap
Page 45 and 46: Implantation procedure SLA ® Openi
Page 47 and 48: p move the implant into final posit
Page 49 and 50: p attach the ratchet (the clockwise
Page 51 and 52: 7. imPLant cLosure after implantati
Page 53 and 54: Immediate restoration of Straumann
Page 55 and 56: Temporary restoration healing caps
Page 57 and 58: 9. aDDitionaL ProDucts Osteotomes p
Page 59 and 60: 10. aDDitionaL information<
Page 61: IMPORTANT NOTES Disclaimer of liabi

Basic information on the SURGICAL PROCEDURE - Straumann

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?