Manual - JÃ¸tul stoves and fireplaces

More documents

Recommendations

Info

138914 Rev. Q 8/28/12MaintenanceThis appliance and its venting system should beinspected before use and at least annually by a qualifiedservice technician.WARNING!THE IGNITION SYSTEM OF THIS APPLIANCECARRIES LIVE VOLTAGE. ALWAYS TURN “OFF “THE MAIN GAS SUPPLY AND DISCONNECT THEPOWER SOURCE BEFORE PERFORMING ANYMAINTENANCE PROCEDURE.TURN “OFF “ THE MAIN GAS SUPPLY AND DIS-CONNECT THE POWER SUPPLY TO THE APPLI-ANCE BEFORE REPLACING BATTERIES.Annual CleaningVent SystemThe entire vent system should be inspected andcleaned every year. If the intake and exhaust ventingis disassembled for any reason, it should be reassembledand sealed according to the vent manufacturer’sinstructions provided at the initial installation.Burner and Log SetPeriodically inspect the firebox and valve compartmentto BE CERTAIN THAT THE FLOW OF COMBUSTIONAND VENTILATION AIR IS UNOBSTRUCTED.The firebox should be vacuumed at least annuallyto remove any surface build up. Use a soft brushattachment and handle the logs carefully as they arefragile.FOR REPLACEMENT, USE ONLY JØTUL CERAMICGLASS PANEL KIT 156817. DO NOT USE ANYOTHER TYPE OF GLASS WITH THIS APPLIANCE.Glass Panel or Gasket Replacement1. Use the 4 mm hex key to remove the four socketscrews that attach the Glass Frame to the firebox.Remove the lower screws first and be sure toadequately support the frame against the fireboxwhile you remove the upper screws.2. Lay the assembly upside down on a flat surface,protecting the frame from scratches using a blanketor towel.3. The glass panel is held in place by four retainertabs. Use a screwdriver to carefully pry these up offthe edge of the glass retaining walls. If the tabsbreak off, use the Tinnerman clips supplied withthe replacement glass kit to secure the glass panelwithin the frame.4. Remove the old gasket material.5. Beginning at the midpoint of the upper edge, applythe new gasket around the glass panel, with theadhesive side inside and the thicker portion on theoutside. DO NOT STRETCH THE GASKET MATERIAL.Trim off any excess, leaving a 1/2” overlap as shownin fig. 60.6. Lay the glass panel within the glass frame and pressthe tabs back down or press the clips in place asshown in fig. 61.Figure 60.Gasket application,PN 129124Glass CareClean the glass as necessary. Wipe the surface witha clean, dampened, soft cloth. Follow with a dry, softtowel. Take care not to scratch the glass surface.WARNING: DO NOT USE ABRASIVE CLEANERSON THE GLASS. NEVER CLEAN THE GLASS WHENIT IS HOT.Gasket InspectionIt is important that the glass gasket be inspected atleast annually. Examine the ribbon gasket for signs ofdeterioration and make sure the gasket has a positiveseal. Replace the gasket if necessary.StarFire Glass EmbersNOTE: Glass embers may discolor over time, dependingupon frequency of use. Clean the embers by washing inwarm, soapy water, and dry thoroughly before reinstallationand use. After washing, discard any permanentlyhazed pieces, or replace embers annually. Colored glassembers, not supplied by Jøtul, maybe used, but must beat least 1/2” and similar in size and shape.30
138914 Rev. Q 8/28/12Figure 61.156817 GlassReplacementKit includesgasket and spareretainer clips.Initializing the Remote ControlEach time you replace the batteries, you will need toinitialize communication between the Receiver andthe Transmitter.1. Place the slider switch in the REMOTE position.2. Insert the end of a paper clip into the hole markedPRG on the Receiver cover. The Receiver will “beep”three (3) times to indicate that it is ready to synchronizewith the Transmitter.3. Install 3 AAA batteries in the Transmitter bay andpush the ON button. The Receiver will “beep” fourtimes to indicate the Transmitter’s command isaccepted and sets to the particular code of thatTransmitter. The system is now initialized.PRGBattery ReplacementBattery life depends on many variables; the quality ofthe batteries, frequency of remote use, and mode ofpilot operation. Keep a supply of good quality batterieson hand to be assured of functional continuity inthe event of a power failure.The Remote Transmitter batteries are easilyaccessed through the tabbed cover plate. Be sure toorient the batteries for correct polarity as indicated inthe battery compartment.WARNING!ALWAYS SHUT OFF THE GAS SUPPLY ANDDISCONNECT THE POWER CORD FROM HOUSECURRENT BEFORE REPLACING BATTERIES.Receiver Battery Replacement1. Push the slider switch into the OFF position. Removethe Receiver cover plate screws and pry thecover plate with slider switch off of the batterybox. See fig. 62.2. Install 4 AA batteries into the receiver bay. Notethe polarity of the batteries and insert into thebattery bay as indicated on the bay cover (+/-).3. With the switch still in the OFF position, align theslider switch with the switch stem and snap thecover plate back onto the battery box.4. Replace the Receiver cover plate screws.Figure 62. Access Receiver batteries.Accent Lamp ReplacementHandle the replacement bulb with gloves. Skin oilswill cause the bulb to fail prematurely.1. Remove the glass frame. See fig. 18.2. Remove the two retainer screws with a short phillipsscrewdriver. Pull the socket out of the housing.3. Plug the new bulb into the socket and re-installthe assembly into the lamp housing.4. Replace the glass frame using the 4 mm hex keyand socket head screws previously removed.PN 222943 Bulb, 130V / 50WFigure 63. Accent Lamp Replacement.31
Page 1 and 2: Jøtul GF 370 DVDirect Vent Gas Sto
Page 3: 138914 Rev. Q 8/28/12Table of Conte
Page 6 and 7: 138914 Rev. Q 8/28/123.0 Safety Inf
Page 8 and 9: 138914 Rev. Q 8/28/12Venting Requir
Page 10 and 11: 138914 Rev. Q 8/28/12Horizontal Ter
Page 12 and 13: 138914 Rev. Q 8/28/12Vent Restricti
Page 14 and 15: 138914 Rev. Q 8/28/12Stove Assembly
Page 16 and 17: 138914 Rev. Q 8/28/125. Fuel Conver
Page 18 and 19: 138914 Rev. Q 8/28/126. High Altitu
Page 20 and 21: 138914 Rev. Q 8/28/12Tumbled Stones
Page 22 and 23: 138914 Rev. Q 8/28/1210. Initial Sy
Page 24 and 25: 138914 Rev. Q 8/28/12Jøtul GF 370
Page 26 and 27: 138914 Rev. Q 8/28/12Remote Transmi
Page 28 and 29: 138914 Rev. Q 8/28/12SPARKELECTRODE
Page 32 and 33: 138914 Rev. Q 8/28/1223 32024283431
Page 34 and 35: 138914 Rev. Q 8/28/12Figure 66. Spu
Page 36 and 37: 138914 Rev. Q 8/28/12Appendix AMobi
Page 38 and 39: 138914 Rev. Q 8/28/12Your stove has
Page 40: August, 2012138914-Q138914 Rev. Q 8

Manual - JÃ¸tul stoves and fireplaces

Create successful ePaper yourself

Delete template?

Save as template?