Manual - JÃ¸tul stoves and fireplaces

More documents

Recommendations

Info

138914 Rev. Q 8/28/12Remote Transmitter Controls, cont’d.Temperature Indication Display• With the transmitter in the OFF position, press theThermostat Key and the Mode Key at the sametime. The display screen will show the current roomtemperature cycling between Farenheit and Celsiusindicators each time the keys are pressed simultaneously.See fig. 42.Turn on the Burner• Press the ON/OFF Key on the Transmitter.The display will show all the active icons. At thesame time, the Receiver will activate the PilotIgnitor. First the pilot will ignite, followed shortlyby the burner. A single”beep” from the Receiver willconfirm reception of the command.Figure 42. Room temperature readingsFigure 43. Burner shut-downTurn off the Burner• Press the ON/OFF Key. The display will show onlythe room temperature and icon. At the same time,the Receiver will deactivate the call for heat and theburner will shut down. Fig. 43. A single”beep” fromthe Receiver will confirm reception of the command.Remote Burner ControlThere are six flame levels available.• With the system ON, and the burner flame levelat maximum, press the Down Arrow Key once toreduce the flame height by one step. Each time theDown Key is pressed, the flame will step down untilthe burner is finally turned off. Fig. 44.• The Up Arrow Key will increase the flame heighteach tim it is pressed. If the U Arrow Key is pressedwhile the system is on but the flame is off, theflame will come on in the High position. Figs. 45-47.A single “beep” will confirm reception of the command.Room Thermostat (Transmitter Operation)The Remote Control can operate as a room themostat.The themostat can be set to a desired temperature tocontrol the comfort level in a room.Figure 44. Burner OFF. Figure 45. Flame Level 1.Figure 46. Flame Level 5. Figure 47. Flame Level 6.Room Temperature• To activate this function, press the Thermostat Key,(Fig. 40.) The display will indicate that the roomthermostat is “ON” and the current Set Temperatureis now displayed. Fig. 48.• To adjust the Set Temperature, press the Up orDown Arrow Keys until the desired Set Temperatureis displayed. Fig.49.26Set TemperatureFigure 48. Thermostat ONFigure 49.Change Set Temperature
138914 Rev. Q 8/28/12SMART Thermostat FunctionThis function adjusts the flame intensity according tothe difference in the Set Point temperature and theactual room temperature. As the room temperaturegets closer to the Set Point, the Smart Function willmodulate flame intensity down.• To activate this function, press the Thermostat Keyuntil the woed “SMART” appears to the right of thethermometer bulb icon. Fig. 50.• To adjust the temperature, press the Up or DownArrow Keys until the desired Set Temperature isdisplayed. Fig. 51.Fan Speed Control• Fan speed can be adjusted through six settings. Toactivate this function, press the Mode Key (Fig. 40)to index to the Fan Control icon. See fig. 52.• Use the Up/Down Arrow Keys to turn ON, OFF, oradjust the fan speed. Fig. 53. A single “beep” willconfirm reception of the command.Figure 50. Smart ModeFigure 52. Fan ModeFigure 51. Smart Set Temp.Figure 53. Fan SpeedAccent Lamp Control ( Auxiliary 120V Outlet)• The auxiliary function controls the Accent Lamppower. Press the Mode Key to index to the AUXicon. Figs. 54-55.• Pressing the Up Arrow Key will turn the Lamp ON.Lamp brightness can be adjusted by turning thedimmer knob on the stove Control Panel.• Pressing the Down Arrow Key will turn the Lamp OFF.Child Safety LockThis function will lockout the Transmitter to preventunsupervised operation.• To activate the Lock, press the Mode key and UP Keyat the same time. Fig. 56.• To de-activate the Lock, press the Mode Key and UPKey at the same time.Low Battery DetectionThe life-span of the batteries depends on variousfactors; battery quality, the frequency of ignition calls,the frequency of changes to Set Points, etc.• When Transmitter batteries are low, the Batteryicon will be displayed before all battery power islost. The icon will disappear when new batteriesare installed.• When Receiver batteries are low, no “beep” willbe emitted from the Receiver when it receives anOn/Off command from the Transmitter. This is analert for a low battery condition in the Receiver.When the batteries are replaced, the “beep” willFigure 54. Lamp ControlFigure 56. Lock ONFigure 55.. Lamp ONFigure 57. Low Batterybe emitted from the Receiver when the ON/OFFKey is pressed. See Battery Replacement under theMaintenance section of this manual.Manual By-Pass of the Remote SystemWhen battery power is low or depleted, the burnercan still be operated manually by sliding the Receiverswitch to the ON position. It will immediately ignitein the High position.In the event of a power failure, flame modulation,themostatic control, fan and lamp functions will beunavailable. It is therefore advisable to keep a supplyof good quality batteries on hand.27
Page 1 and 2: Jøtul GF 370 DVDirect Vent Gas Sto
Page 3: 138914 Rev. Q 8/28/12Table of Conte
Page 6 and 7: 138914 Rev. Q 8/28/123.0 Safety Inf
Page 8 and 9: 138914 Rev. Q 8/28/12Venting Requir
Page 10 and 11: 138914 Rev. Q 8/28/12Horizontal Ter
Page 12 and 13: 138914 Rev. Q 8/28/12Vent Restricti
Page 14 and 15: 138914 Rev. Q 8/28/12Stove Assembly
Page 16 and 17: 138914 Rev. Q 8/28/125. Fuel Conver
Page 18 and 19: 138914 Rev. Q 8/28/126. High Altitu
Page 20 and 21: 138914 Rev. Q 8/28/12Tumbled Stones
Page 22 and 23: 138914 Rev. Q 8/28/1210. Initial Sy
Page 24 and 25: 138914 Rev. Q 8/28/12Jøtul GF 370
Page 28 and 29: 138914 Rev. Q 8/28/12SPARKELECTRODE
Page 30 and 31: 138914 Rev. Q 8/28/12MaintenanceThi
Page 32 and 33: 138914 Rev. Q 8/28/1223 32024283431
Page 34 and 35: 138914 Rev. Q 8/28/12Figure 66. Spu
Page 36 and 37: 138914 Rev. Q 8/28/12Appendix AMobi
Page 38 and 39: 138914 Rev. Q 8/28/12Your stove has
Page 40: August, 2012138914-Q138914 Rev. Q 8

Manual - JÃ¸tul stoves and fireplaces

Create successful ePaper yourself

Delete template?

Save as template?