Manual - JÃ¸tul stoves and fireplaces

More documents

Recommendations

Info

138914 Rev. Q 8/28/1210. Initial System CheckThe burner and fan control system consists of the followingbuilt-in or supplied components:1) Remote Transmitter - 3, AAA batteries preinstalled2) Remote Receiver - 4, AA backup batteries preinstalled3) Fan Control Module - switchedAll internal connections have been made at thefactory. The remote controls are preprogramed andthe entire system tested.NOTE: Check the build date on the shippingcrate label. If it has been more than 6 monthssince the build date, be prepared to replacethe Receiver and Transmitter batteries.Follow this procedure for the initial system check followinginstallation:1. Connect the power extension cord to the interiorpower cord and to a 120V electrical outlet.2. Turn the Fan Control Module rocker switch to theON position, fig. 35a. It is located in the valve compartment,behind the Receiver control box.3. Slide the Remote Receiver switch to the ON position.The ignitor will generate spark in either IPI orCPI pilot modes. See fig. 35b.4. PURGING THE GAS LINE: Open the gas supplyvalve. When lighting the appliance for the firsttime it will take a few moments to clear the gasline of air. Once the purge is complete, the pilotlight will ignite.5. PILOT FLAME: The pilot flame should be steady -not lifting or floating. The flame should be blue incolor around the pilot hood, with traces of yellowtoward the outer edges. It is important that thepilot flame engulf the top 1/8” of the flame sensor.The pilot flame should project out of the pilothood 1” from both ports extending to reach theburner plate ports. See fig. 36. The pilot flame canbe tuned by turning the adjustment screw locatedon the front of the valve. See fig. 20.6. INSTALLER PLEASE NOTE:CHECK FUNCTIONALITY. The burner, remotecontrol and fan functions have each been testedat the factory. However, it is important to runthrough each function and be sure to familiarizethe homeowner with the operation procedures.See the Operation section on pages 24-27 fordetails regarding Remote Control functions andsettings.Open outlet- not usedFlame SensortoFan120V OUT FAN AUX OUT COMON REMOTE OFFIgnitorCarry-over PortstoAccent LampFigure 35b. Initial system settings.Figure 36. Correct Pilot flame pattern.POWER= POWER ON= POWER OFFFigure 35a. Fan Control Module power switch.CPI / Continuous Pilot Ignition(Standing Pilot)ORIPI / Intermittent Pilot IgnitionPRGRemote ReceiverSwitch22
138914 Rev. Q 8/28/12Flame Appearance / Air ShutterAdjustmentWARNING:AIR SHUTTER ADJUSTMENTS SHOULD ONLY BEPERFORMED BY A QUALIFIED, PROFESSIONALSERVICE TECHNICIAN.Locate the Primary Air Shutter control under the fireboxfloor above the gas valve. See fig. 37. The shutteris set at the midpoint of its adjustment range at thefactory. This will give good results in the majority ofinstallation configurations, however, you may needfind it necessary to adjust it to get the best flamepicture depending upon the your specific installation.With the burner operating, loosen the wingnuton the shutter stem. Push the stem back toward therear of the stove will decrease combustion air. Pull itforward to increase air.Generally, flame appearance is a matter of individualpreference, however a warm yellowish flame ismost common.• Closing the air shutter - in extreme cases maygenerate very long yellow flames resulting in soot.Sooting produces black deposits on the logs, on theinside walls of the appliance, and potentially onthe exterior termination cap.Sooting is caused by incomplete combustion in theflames and lack of combustion air entering the airshutter opening.• Opening the air shutter - will generate a flame thatis blue and transparent, or “anemic”. This flame isgenerally more efficient, but not as attractive.• Allow the burner to operate at the highest settingfor 20-30 minutes before making any adjustments.Always make adjustments in 1/8” increments andallow the burner to settle-in for 10- 15 minutesbetween additional adjustments.Primary AirShutterFigure 37. Primary Air Shutter location.Figure 38. Proper flame picture -Traditional Logs.Alternate flame pictures for Wishing Rock and StarfireGlass are illustrated in figs. 67 & 68 in the Appendix onpage 36.Operation Notes1. For the first several hours of operation, it is commonto detect some odor as the metal and manufacturingmaterials cure under heat. This conditionis temporary and can be alleviated by allowingplenty of fresh air to circulate through the area.2. Condensation may develop on the glass upon eachlighting of the appliance. This “fog” will disappearas the glass heats.3. Keep the controls and the area under the appliancefree of dust. Always keep the appliance area clearand free from combustible materials, gasoline andother flammable liquids.4. This appliance can be operated with a continuouslyburning pilot flame. Exercise caution whenusing household products containing combustiblevapors.5. CAUTION: DO NOT OPERATE THIS APPLIANCEWITH THE GLASS REMOVED, CRACKED OR BROKEN.REPLACEMENT OF THE GLASS SHOULD BE DONE BYA LICENSED OR QUALIFIED SERVICE PERSON. USEONLY REPLACEMENT GLASS PROVIDED BY YOURAUTHORIZED JØTUL DEALER. NEVER USE ANY SUB-STITUTE MATERIALS.23
Page 1 and 2: Jøtul GF 370 DVDirect Vent Gas Sto
Page 3: 138914 Rev. Q 8/28/12Table of Conte
Page 6 and 7: 138914 Rev. Q 8/28/123.0 Safety Inf
Page 8 and 9: 138914 Rev. Q 8/28/12Venting Requir
Page 10 and 11: 138914 Rev. Q 8/28/12Horizontal Ter
Page 12 and 13: 138914 Rev. Q 8/28/12Vent Restricti
Page 14 and 15: 138914 Rev. Q 8/28/12Stove Assembly
Page 16 and 17: 138914 Rev. Q 8/28/125. Fuel Conver
Page 18 and 19: 138914 Rev. Q 8/28/126. High Altitu
Page 20 and 21: 138914 Rev. Q 8/28/12Tumbled Stones
Page 24 and 25: 138914 Rev. Q 8/28/12Jøtul GF 370
Page 26 and 27: 138914 Rev. Q 8/28/12Remote Transmi
Page 28 and 29: 138914 Rev. Q 8/28/12SPARKELECTRODE
Page 30 and 31: 138914 Rev. Q 8/28/12MaintenanceThi
Page 32 and 33: 138914 Rev. Q 8/28/1223 32024283431
Page 34 and 35: 138914 Rev. Q 8/28/12Figure 66. Spu
Page 36 and 37: 138914 Rev. Q 8/28/12Appendix AMobi
Page 38 and 39: 138914 Rev. Q 8/28/12Your stove has
Page 40: August, 2012138914-Q138914 Rev. Q 8

Manual - JÃ¸tul stoves and fireplaces

Create successful ePaper yourself

Delete template?

Save as template?