Manual - JÃ¸tul stoves and fireplaces

More documents

Recommendations

Info

138914 Rev. Q 8/28/126. High Altitude AdjustmentThe decreased atmospheric pressure of higher altitudesaffects heat value of gaseous fuels. Most gassuppliers derate the gas intended for use at elevationsabove 2000 feet. Check with your gas supplierbefore performing derate adjustment to the burner.This appliance may be adjusted for altitude over2000 ft. (610 - 1371 m) for natural gas.If the gas supplier does not derate fuels, install HighAltitude Adjustment Kit 156822 for Natural gas.DO NOT DERATE FOR PROPANE.U.S & Canada perANSI Z21.88-2005•CSA 2.33-2005, CAN/CGA 2.17For natural gas installations from 610-1370 meters(2000-4500 ft.) the orifice size (DMS) is #39. Seedata plate for additional information. For highaltitude installations consult the local gas distributoror the authority having jurisdiction for proper ratingmethods. If the installer must convert the unit toadjust for varying altitudes, the information stickermust be filled out and applied to the appliance at thetime of the conversion.Cet appareil est equippé pour des altitudes compriesentre 0 et 2000 pieds (0-610 m ) seulement.Derating Procedure• Follow Steps 1-6 of the Fuel Conversion procedureon pages 16 to change the burner injector. Use theinjector supplied with the kit. Detailed instructionsare also included in the kit.• Conduct gas leak and gas pressure tests as detailedon page 15 of this manual.• Conduct system check and flame picture adjustmentsas specified on pages 22-23.INSTALLER: Fill out the appropriate informationand apply the high altitude conversion label providedto the rating plate on the appliance. See fig. 24.This appliance has been converted for use at analtitude of___________ .Orifice Size: __________ Manifold Press. _______Input Btu/Hr. _________ Fuel Type ___________Date: ___/___/___ Converted by:_____________Cet appreeil a été converti au _____ Injecteur_____Pression à la tubulure d’alimentation ___________Déoit calorifique ___________Figure 24. High Altitude Conversion Label.7. Firebox Panel InstallationSkamol Panels and optionalReflective Glass Kit 156817Skamol PanelsThese insulating panels are installed at the factory.If desired, the panels may be painted black using anyhigh-temperature paint. DO NOT OPERATE THIS STOVEWITHOUT THE SKAMOL PANELS INSTALLED.The labeled lower panel retainer bracket shouldbe removed from the firebox - it is intended only toprevent shipping damage.Reflective Glass Panels• 1/4” socket driver requiredCotton gloves are provided with the glass panels. Usethem to handle the panels to prevent fingerprints onthe surfaces. Fingerprints are difficult to remove. Use aclean cloth to remove any dust from the glass panels.1. You will need to remove the pilot hood and burnerplate to provide clearance to install the glasspanels. Pull the pilot hood off of the pilot base - itwill slip past its retainer clip. Loosen the Air Shutterand push it all the way back to disengage theburner venturi tube from the shutter. Simply liftthe burner up and out of the firebox. See figs. 21and 23.2. Loosen, but do not remove the three #8 x 12 sheetmetal screws that secure the upper panel retainer.Pull the the retainer forward about 1/4 inch. Seefig. 25.3. Orient the rear panel, shiny side out, textured sidein. Tilt the panel to engage its upper edge behindthe retainer bracket. Seat the panel all the way backand centered against the back wall. See fig. 26.4. Orient the side panels, shiny side out, and slidingeach behind the retainer wings. See Fig. 26a.5. Push the retainer back against the glass panels andtighten the three sheet metal screws.6. Replace the burner plate. When properly located, itwill be level and secure.7. Replace the pilot head. It will just snap back intoplace on the base.8. Air Shutter Adjustment: Follow the guidelines onpage 23 to establish the best flame picture for yourparticular installation.18
138914 Rev. Q 8/28/128. Install Burner MediaPanel RetainerBracketFigure 25. Loosen the panel retainer screws.River RocksCAUTION: THE ROCKS ARE FRAGILE! SUPPORT THEASSEMBLY FROM THE BOTTOM AND HANDLE CARE-FULLY!1. Engage the River Rock bed with the two centerburner pins as shown in fig. 27. Either side of therocks may face outward as desired.2. Evenly disperse the Ember Stones supplied overthe burner plate around the log parts. DO NOTALLOW EMBER STONES TO BLOCK THE PILOT AS-SEMBLY AREA. The carry-over ports directly in frontof the pilot must remain clear for proper pilotignition. See figs. 29 and 65 for examples.StarFire Glass EmbersDo not use more than the four pounds (in two, 2 lb.bags) of glass media provided. For best results, evenlyspread the contents of the bag over the entire burnerplate and rear skirt, mounding a crown toward thecenter. DO NOT COVER THE AREA IMMEDIATELY INFRONT OF THE PILOT ASSEMBLY. The carry-over portsdirectly in front of the pilot assembly must be clear toensure proper pilot ignition. See fig. 66 page 34.Rear Glass PanelFigure 26. Install Rear Glass Panel.Figure 27. Set River Rock assembly on pins.Figure 26a. Install Side Glass Panels.19
Page 1 and 2: Jøtul GF 370 DVDirect Vent Gas Sto
Page 3: 138914 Rev. Q 8/28/12Table of Conte
Page 6 and 7: 138914 Rev. Q 8/28/123.0 Safety Inf
Page 8 and 9: 138914 Rev. Q 8/28/12Venting Requir
Page 10 and 11: 138914 Rev. Q 8/28/12Horizontal Ter
Page 12 and 13: 138914 Rev. Q 8/28/12Vent Restricti
Page 14 and 15: 138914 Rev. Q 8/28/12Stove Assembly
Page 16 and 17: 138914 Rev. Q 8/28/125. Fuel Conver
Page 20 and 21: 138914 Rev. Q 8/28/12Tumbled Stones
Page 22 and 23: 138914 Rev. Q 8/28/1210. Initial Sy
Page 24 and 25: 138914 Rev. Q 8/28/12Jøtul GF 370
Page 26 and 27: 138914 Rev. Q 8/28/12Remote Transmi
Page 28 and 29: 138914 Rev. Q 8/28/12SPARKELECTRODE
Page 30 and 31: 138914 Rev. Q 8/28/12MaintenanceThi
Page 32 and 33: 138914 Rev. Q 8/28/1223 32024283431
Page 34 and 35: 138914 Rev. Q 8/28/12Figure 66. Spu
Page 36 and 37: 138914 Rev. Q 8/28/12Appendix AMobi
Page 38 and 39: 138914 Rev. Q 8/28/12Your stove has
Page 40: August, 2012138914-Q138914 Rev. Q 8

Manual - JÃ¸tul stoves and fireplaces

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?