Manual - Jøtul stoves and fireplaces

138914 Rev. Q 8/28/126. High Altitude AdjustmentThe decreased atmospheric pressure of higher altitudesaffects heat value of gaseous fuels. Most gassuppliers derate the gas intended for use at elevationsabove 2000 feet. Check with your gas supplierbefore performing derate adjustment to the burner.This appliance may be adjusted for altitude over2000 ft. (610 - 1371 m) for natural gas.If the gas supplier does not derate fuels, install HighAltitude Adjustment Kit 156822 for Natural gas.DO NOT DERATE FOR PROPANE.U.S & Canada perANSI Z21.88-2005•CSA 2.33-2005, CAN/CGA 2.17For natural gas installations from 610-1370 meters(2000-4500 ft.) the orifice size (DMS) is #39. Seedata plate for additional information. For highaltitude installations consult the local gas distributoror the authority having jurisdiction for proper ratingmethods. If the installer must convert the unit toadjust for varying altitudes, the information stickermust be filled out and applied to the appliance at thetime of the conversion.Cet appareil est equippé pour des altitudes compriesentre 0 et 2000 pieds (0-610 m ) seulement.Derating Procedure• Follow Steps 1-6 of the Fuel Conversion procedureon pages 16 to change the burner injector. Use theinjector supplied with the kit. Detailed instructionsare also included in the kit.• Conduct gas leak and gas pressure tests as detailedon page 15 of this manual.• Conduct system check and flame picture adjustmentsas specified on pages 22-23.INSTALLER: Fill out the appropriate informationand apply the high altitude conversion label providedto the rating plate on the appliance. See fig. 24.This appliance has been converted for use at analtitude of___________ .Orifice Size: __________ Manifold Press. _______Input Btu/Hr. _________ Fuel Type ___________Date: ___/___/___ Converted by:_____________Cet appreeil a été converti au _____ Injecteur_____Pression à la tubulure d’alimentation ___________Déoit calorifique ___________Figure 24. High Altitude Conversion Label.7. Firebox Panel InstallationSkamol Panels and optionalReflective Glass Kit 156817Skamol PanelsThese insulating panels are installed at the factory.If desired, the panels may be painted black using anyhigh-temperature paint. DO NOT OPERATE THIS STOVEWITHOUT THE SKAMOL PANELS INSTALLED.The labeled lower panel retainer bracket shouldbe removed from the firebox - it is intended only toprevent shipping damage.Reflective Glass Panels• 1/4” socket driver requiredCotton gloves are provided with the glass panels. Usethem to handle the panels to prevent fingerprints onthe surfaces. Fingerprints are difficult to remove. Use aclean cloth to remove any dust from the glass panels.1. You will need to remove the pilot hood and burnerplate to provide clearance to install the glasspanels. Pull the pilot hood off of the pilot base - itwill slip past its retainer clip. Loosen the Air Shutterand push it all the way back to disengage theburner venturi tube from the shutter. Simply liftthe burner up and out of the firebox. See figs. 21and 23.2. Loosen, but do not remove the three #8 x 12 sheetmetal screws that secure the upper panel retainer.Pull the the retainer forward about 1/4 inch. Seefig. 25.3. Orient the rear panel, shiny side out, textured sidein. Tilt the panel to engage its upper edge behindthe retainer bracket. Seat the panel all the way backand centered against the back wall. See fig. 26.4. Orient the side panels, shiny side out, and slidingeach behind the retainer wings. See Fig. 26a.5. Push the retainer back against the glass panels andtighten the three sheet metal screws.6. Replace the burner plate. When properly located, itwill be level and secure.7. Replace the pilot head. It will just snap back intoplace on the base.8. Air Shutter Adjustment: Follow the guidelines onpage 23 to establish the best flame picture for yourparticular installation.18