PDF Output - O&O Software
PDF Output - O&O Software PDF Output - O&O Software
Getting StartedFile cache viewTip: When you use the Status monitor, the same data are displayed in the smaller status monitor windowaccessed through the task tray icon.System MonitorWith the System Monitor, you can monitor the performance of the most important components on yoursystem. The system monitor is enabled by default.Included in the System Monitor are current readings measurements from your processor, main memory,system cache and the hard disk.Whenever the system monitor is active, you can select individual components in the Ribbon Bar in System(processor, main memory, system cache, hard disk) and display the statistics of the individual components.When the System Monitor is deactivated, the component icons cannot be selected.If the system monitor should be deactivated, you can select it over the Ribbon Bar over Settings/Enablesystem monitor.Note: For the System Monitor to successfully run, it may be that additional components need to be activated.This could require the use of additional memory resources.More:ProcessorMain MemorySystem CacheHard diskUse of the processorsIn this section, the load on the processor is measured and displayed over time as a graph. The units areexplained in the legend. You can use a smaller view on the start page of O&O CleverCache (ControlCenter). You will find a more detailed view under hard disk in the Ribbon Bar. The units are explained in thelegend. The statistical values for mean, maximum, and minimum can be found below the graph.O&O CleverCache - 14
Getting StartedView of the use of the processorUse of the main memoryIn this section, the load on the main memory is measured and displayed over time as a graph. You can usea smaller view on the start page of O&O CleverCache (Control Center). You will find a more detailed viewunder main memory in the Ribbon Bar. The units are explained in more detail in the Ribbon Bar. The statisticalvalues for mean, maximum, and minimum can be found below the graph.O&O CleverCache - 15
- Page 2 and 3: CopyrightsText, illustrations and e
- Page 4 and 5: Hard disk 17Close O&O CleverCache 1
- Page 6 and 7: About O&O CleverCache 7• O&O Clev
- Page 8 and 9: About O&O CleverCache 7reboot of th
- Page 10 and 11: InstallationInstallationInstalling
- Page 12 and 13: Installation1. Open the Control Pan
- Page 14 and 15: Online registration• Be supplied
- Page 16 and 17: Getting StartedCustomizing the Most
- Page 20 and 21: Getting StartedUse of the main memo
- Page 22 and 23: Getting StartedClose O&O CleverCach
- Page 24 and 25: Manage profilesManage profilesO&O C
- Page 26 and 27: Manage profilesDelete ProfilesTo de
- Page 28 and 29: Customize settingsCustomize setting
- Page 30 and 31: Customize settingsIf the load on yo
- Page 32 and 33: Customize settingsNote: If you are
- Page 34 and 35: Customize settingsMem-O-SafeSystem
- Page 36 and 37: Customize settingsImportant: Please
- Page 38 and 39: Customize settingsTrayIcon with sel
- Page 40 and 41: Support and ContactSupport and Cont
- Page 42 and 43: End user license agreement 2.1 (EUL
- Page 44 and 45: End user license agreement 2.1 (EUL
- Page 46 and 47: End user license agreement 2.1 (EUL
- Page 48 and 49: End user license agreement 2.1 (EUL
- Page 50 and 51: End user license agreement 2.1 (EUL
- Page 52: End user license agreement 2.1 (EUL
Getting StartedFile cache viewTip: When you use the Status monitor, the same data are displayed in the smaller status monitor windowaccessed through the task tray icon.System MonitorWith the System Monitor, you can monitor the performance of the most important components on yoursystem. The system monitor is enabled by default.Included in the System Monitor are current readings measurements from your processor, main memory,system cache and the hard disk.Whenever the system monitor is active, you can select individual components in the Ribbon Bar in System(processor, main memory, system cache, hard disk) and display the statistics of the individual components.When the System Monitor is deactivated, the component icons cannot be selected.If the system monitor should be deactivated, you can select it over the Ribbon Bar over Settings/Enablesystem monitor.Note: For the System Monitor to successfully run, it may be that additional components need to be activated.This could require the use of additional memory resources.More:ProcessorMain MemorySystem CacheHard diskUse of the processorsIn this section, the load on the processor is measured and displayed over time as a graph. The units areexplained in the legend. You can use a smaller view on the start page of O&O CleverCache (ControlCenter). You will find a more detailed view under hard disk in the Ribbon Bar. The units are explained in thelegend. The statistical values for mean, maximum, and minimum can be found below the graph.O&O CleverCache - 14