Administration of the Avaya G350 Media Gateway - Avaya Support
Administration of the Avaya G350 Media Gateway - Avaya Support Administration of the Avaya G350 Media Gateway - Avaya Support
Configuring contact closureContact closure hardware configurationTo configure your hardware for contact closure:1. Connect an Avaya Partner Contact Closure Adjunct to the Contact Closure port on theAvaya G350 Media Gateway front panel. The Contact Closure port is labeled CC. Use atelephone cable with standard RJ-11 connectors.2. A qualified electrician should connect the electrical devices to the relays on the AvayaPartner Contact Closure Adjunct. For information on contact closure specifications, seeOverview of the Avaya G350 Media Gateway, 555-245-201.Contact closure software configurationYou can specify the following contact closure modes:Modemgcmanual-triggermanual-offDescriptionThe MGC controls contact closure. In mgc mode, theuser dials feature access codes to activate anddeactivate contact closure.Activates contact closure for the specified relay.Deactivates contact closure for the specified relay.To configure the Avaya G350 Media Gateway to activate contact closure when the featureaccess code is dialed:1. Enter the set contact-closure admin command. In the following example, thecommand sets contact closure to work in relay 1 of the Avaya Partner Contact ClosureAdjunct when activated by the call controller.set contact-closure admin 10/1:1 mgc2. Use the set contact-closure pulse-duration command to set the length of timefor the relay to return to normal after the call controller triggers it. In the following example,the command sets relay 2 of the Avaya Partner Contact Closure Adjunct to return to normal5 seconds after the call controller triggers contact closure in the relay.set contact-closure pulse-duration 10/1:2 5152 Administration of the Avaya G350 Media Gateway
Showing contact closure statusTo activate contact closure manually, use the set contact-closure admin command withthe parameter manual-trigger. In the following example, the command activates contactclosure in relay 1 of the Avaya Partner Contact Closure Adjunct. Contact closure remains activeuntil you deactivate it by using the set contact-closure admin command with theparameter manual-off or mgc.set contact-closure admin 10/1:1 manual-triggerTo deactivate contact closure manually, use the set contact-closure admin commandwith the parameter manual-off. In the following example, the command deactivates contactclosure in relay 2 of the Avaya Partner Contact Closure Adjunct. Contact closure will notoperate, even automatically, until you use the set contact-closure admin command tochange the status of contact closure to mgc or manual-trigger.set contact-closure admin 10/1:2 manual-offShowing contact closure statusUse the show contact-closure command to display the status of one or more contactclosure relays. The following example displays the contact closure status of relay 1 of the AvayaPartner Contact Closure Adjunct box.G350-101(super)# show contact-closureMODULE PORT RELAY ADMIN PULSE DURATION (secs) STATUS------- ----- ------ ---------------- --------------------- ------10 1 1 mgc 5 secs off10 1 2 mgc 3 secs offIssue 3 January 2005 153
- Page 102 and 103: Configuring a WAN InterfaceNote:Not
- Page 104 and 105: Configuring a WAN InterfaceIf one o
- Page 106 and 107: Configuring a WAN InterfacePPP VoIP
- Page 108 and 109: Configuring a WAN Interface● VLAN
- Page 110 and 111: Configuring a WAN Interface110 Admi
- Page 112 and 113: Configuring PoELoad detectionThe MM
- Page 114 and 115: Configuring PoEPoE configuration CL
- Page 116 and 117: Configuring PoE116 Administration o
- Page 118 and 119: Configuring Emergency Transfer Rela
- Page 120 and 121: Configuring SNMPThere are several w
- Page 122 and 123: Configuring SNMPUsersSNMPv3 uses th
- Page 124 and 125: Configuring SNMPGroup NameSecurityM
- Page 126 and 127: Configuring SNMP- notification type
- Page 128 and 129: Configuring SNMPConfiguring dynamic
- Page 130 and 131: Configuring SNMPThe following examp
- Page 132 and 133: Configuring advanced switchingVLAN
- Page 134 and 135: Configuring advanced switchingMulti
- Page 136 and 137: Configuring advanced switching●
- Page 138 and 139: Configuring advanced switchingRelia
- Page 140 and 141: Configuring advanced switchingSwitc
- Page 142 and 143: Configuring advanced switchingPort
- Page 144 and 145: Configuring advanced switchingThe S
- Page 146 and 147: Configuring advanced switching●Po
- Page 148 and 149: Configuring advanced switchingThe f
- Page 150 and 151: Configuring advanced switchingPort
- Page 154 and 155: Configuring contact closure154 Admi
- Page 156 and 157: Configuring RMON monitoringRMON CLI
- Page 158 and 159: Configuring RMON monitoring158 Admi
- Page 160 and 161: Configuring the routerOverview of t
- Page 162 and 163: Configuring the routerLayer 2 logic
- Page 164 and 165: Configuring the routerStatic routes
- Page 166 and 167: Configuring the routerRouting table
- Page 168 and 169: Configuring the routerRouting packe
- Page 170 and 171: Configuring the routerThe following
- Page 172 and 173: Configuring the routerDynamic MTU d
- Page 174 and 175: Configuring the routerAdditional GR
- Page 176 and 177: Configuring the routerYou can use t
- Page 178 and 179: Configuring the routerDHCP/BOOTP re
- Page 180 and 181: Configuring the routerApplication
- Page 182 and 183: Configuring the routerNote:Note:If
- Page 184 and 185: Configuring the routerG350-001(supe
- Page 186 and 187: Configuring the routerDirected broa
- Page 188 and 189: Configuring the routerDynamic ARP t
- Page 190 and 191: Configuring the routerConfiguring I
- Page 192 and 193: Configuring the routerPoison-revers
- Page 194 and 195: Configuring the router●●●●U
- Page 196 and 197: Configuring the routerOSPF commands
- Page 198 and 199: Configuring the routerand what metr
- Page 200 and 201: Configuring the router●●●●
Showing contact closure statusTo activate contact closure manually, use <strong>the</strong> set contact-closure admin command with<strong>the</strong> parameter manual-trigger. In <strong>the</strong> following example, <strong>the</strong> command activates contactclosure in relay 1 <strong>of</strong> <strong>the</strong> <strong>Avaya</strong> Partner Contact Closure Adjunct. Contact closure remains activeuntil you deactivate it by using <strong>the</strong> set contact-closure admin command with <strong>the</strong>parameter manual-<strong>of</strong>f or mgc.set contact-closure admin 10/1:1 manual-triggerTo deactivate contact closure manually, use <strong>the</strong> set contact-closure admin commandwith <strong>the</strong> parameter manual-<strong>of</strong>f. In <strong>the</strong> following example, <strong>the</strong> command deactivates contactclosure in relay 2 <strong>of</strong> <strong>the</strong> <strong>Avaya</strong> Partner Contact Closure Adjunct. Contact closure will notoperate, even automatically, until you use <strong>the</strong> set contact-closure admin command tochange <strong>the</strong> status <strong>of</strong> contact closure to mgc or manual-trigger.set contact-closure admin 10/1:2 manual-<strong>of</strong>fShowing contact closure statusUse <strong>the</strong> show contact-closure command to display <strong>the</strong> status <strong>of</strong> one or more contactclosure relays. The following example displays <strong>the</strong> contact closure status <strong>of</strong> relay 1 <strong>of</strong> <strong>the</strong> <strong>Avaya</strong>Partner Contact Closure Adjunct box.<strong>G350</strong>-101(super)# show contact-closureMODULE PORT RELAY ADMIN PULSE DURATION (secs) STATUS------- ----- ------ ---------------- --------------------- ------10 1 1 mgc 5 secs <strong>of</strong>f10 1 2 mgc 3 secs <strong>of</strong>fIssue 3 January 2005 153