Operating Instructions - Snap-on Equipment
Operating Instructions - Snap-on Equipment Operating Instructions - Snap-on Equipment
Pocket PC Maintenance5. If the test is Good, the Communications Good status displays.Figure 2G-30: Communications Good Diagnostics StatusProceed to Step 7.6. If test results are Bad, the Communications Bad status displays. Thisindicates a problem with the communication/serial cable connection to thepocket PC, a faulty cable, the software on the pocket PC is corrupted orthe pocket PC has failed.Figure 2G-31: Communications Bad Diagnostics Status— Unplug the pocket PC communication/serial cable from the pocket PC.Reconnect and repeat the test or try a replacement cable (a spare isprovided with the pocket PC).— Reload software on the pocket PC and try again.— If the problem continues, try a different pocket PC.Proceed to Step 7.2G-24
Pocket PC Maintenance7. Press the Stop Test button to finish the test. The Finish Test screendisplays, Figure 2G-32.Figure 2G-32: Comm Test Finish Diagnostics Screen8. When the test has completed, remove the loop back tester and selectFinish.✓ Be sure to remove the loop back tester before selecting Finish.If the communications status is Good, reconnect the communication/serial cable tothe FGA. The system should be working.— If you continue to experience communication problems with the FGAeven though the Comm Test is good, check the FGA operator’smanual for a possible FGA problem.— If problems still occur, charge the FGA for 24 hours and repeat thetest.2G-25
- Page 37 and 38: Pocket PC Meters/GraphBar GraphTo b
- Page 39 and 40: Pocket PC Meters/GraphConfiguration
- Page 41 and 42: Pocket PC Meters/GraphResultsThe po
- Page 43 and 44: Pocket PCAutomatic Tests2DTSI TestT
- Page 45 and 46: Pocket PC Automatic TestsHigh RPM T
- Page 47 and 48: Pocket PC Automatic TestsTest Compl
- Page 49 and 50: Pocket PC Automatic TestsCatalyst T
- Page 51 and 52: Pocket PC Automatic Tests5. When pr
- Page 53 and 54: Pocket PC Automatic TestsIf the res
- Page 55 and 56: Pocket PCCustomer/Vehicle2EFGA is d
- Page 57 and 58: Pocket PC Customer/Vehicle✓ To di
- Page 59 and 60: Pocket PC Customer/Vehicle2. Choose
- Page 61 and 62: 2FPocket PC ResultsTest ResultsThe
- Page 63 and 64: Pocket PC ResultsChange StandardsCu
- Page 65 and 66: Pocket PCMaintenance2GThis section
- Page 67 and 68: Pocket PC Maintenance6. Press OK to
- Page 69 and 70: Pocket PC MaintenanceIf the reading
- Page 71 and 72: Pocket PC Maintenance✓ Always mak
- Page 73 and 74: Pocket PC Maintenance3. Remove the
- Page 75 and 76: Pocket PC MaintenanceSetupThis sect
- Page 77 and 78: Pocket PC MaintenanceRPM/Temp Kit
- Page 79 and 80: Pocket PC MaintenanceTSI / Idle Set
- Page 81 and 82: Pocket PC MaintenanceStandardsThe S
- Page 83 and 84: Pocket PC MaintenanceFigure 2G-23:
- Page 85 and 86: Pocket PC MaintenanceBoard Diagnost
- Page 87: Pocket PC MaintenanceTo perform the
- Page 91 and 92: Pocket PC MaintenanceFigure 2G-34:
- Page 93 and 94: Pocket PC MaintenanceLow Out FlowTh
- Page 95 and 96: Pocket PCOther Functions2HAboutThis
- Page 97 and 98: 3Using FGA with the PCThe Flexible
- Page 99 and 100: 3APC Software OverviewThe PC versio
- Page 101 and 102: PC Software OverviewCommands 1-10Co
- Page 103 and 104: PC Software OverviewCommandsFigure
- Page 105 and 106: 3BPC SoftwareInstallationThe Flexib
- Page 107 and 108: PC Software Installation5. If this
- Page 109 and 110: 3CPC Meters/Strip ChartThis chapter
- Page 111 and 112: PC Meters/GraphGas Bench MenuThe Ga
- Page 113 and 114: PC Meters/GraphStrip ChartTo view t
- Page 115 and 116: PC Meters/GraphStrip Chart Display
- Page 117 and 118: PC Meters/GraphWhen you select the
- Page 119 and 120: PC Meters/GraphTachometerUse the Ta
- Page 121 and 122: PC Automatic Tests3DTSI TestThis se
- Page 123 and 124: PC Automatic TestsTachometer Config
- Page 125 and 126: PC Automatic TestsIdle RPM TestFGA
- Page 127 and 128: PC Automatic TestsTSI Results16. Th
- Page 129 and 130: 3EPC Customer/VehicleFGA is designe
- Page 131 and 132: PC Customer/VehicleInformation bar
- Page 133 and 134: PC Customer/VehicleWhen the desired
- Page 135 and 136: 3FPC ResultsThe Test Results window
- Page 137 and 138: 3GPC MaintenanceGas CalibrationThis
Pocket PC Maintenance5. If the test is Good, the Communicati<strong>on</strong>s Good status displays.Figure 2G-30: Communicati<strong>on</strong>s Good Diagnostics StatusProceed to Step 7.6. If test results are Bad, the Communicati<strong>on</strong>s Bad status displays. Thisindicates a problem with the communicati<strong>on</strong>/serial cable c<strong>on</strong>necti<strong>on</strong> to thepocket PC, a faulty cable, the software <strong>on</strong> the pocket PC is corrupted orthe pocket PC has failed.Figure 2G-31: Communicati<strong>on</strong>s Bad Diagnostics Status— Unplug the pocket PC communicati<strong>on</strong>/serial cable from the pocket PC.Rec<strong>on</strong>nect and repeat the test or try a replacement cable (a spare isprovided with the pocket PC).— Reload software <strong>on</strong> the pocket PC and try again.— If the problem c<strong>on</strong>tinues, try a different pocket PC.Proceed to Step 7.2G-24