Operating Instructions - Snap-on Equipment
Operating Instructions - Snap-on Equipment Operating Instructions - Snap-on Equipment
Pocket PC MaintenanceFigure 2G-1: Initial Gas Calibration Screen3. Verify that the gas analyzer sample system exhaust hose is connected tothe port labeled Exhaust.4. Disconnect the vehicle exhaust sample hose from the filter bowl.5. Press the Start button to begin Calibration.Figure 2G-2: Calibration Values ScreenThe Calibration Values screen shown in Figure 2G-2 displays allowing youto verify that the calibration values being used match the concentrationvalues of the calibration bottle. Change the values if necessary.✓ You can change the values on this screen by tapping on thenumber and editing in place or in Maintenance > Setup > GeneralSetup > Calibration.2G-2
Pocket PC Maintenance6. Press OK to continue.— FGA purges old gases and residue out of the system.Figure 2G-3: Purging Screen— FGA then performs a zero calibration.✓ Make sure the vehicle exhaust sample probe is in fresh air, NOTconnected to the filter bowl Quick Coupler. The analyzer mustsample fresh air.Figure 2G-4: Zero Calibration Screen2G-3
- Page 17 and 18: Introduction and Equipment Overview
- Page 19 and 20: Introduction and Equipment Overview
- Page 21 and 22: Using FGA with thePocket PC2The Fle
- Page 23 and 24: Pocket PCSoftware Overview2AThe poc
- Page 25 and 26: Pocket PC Software OverviewBattery
- Page 27 and 28: Pocket PC Software OverviewSoftware
- Page 29 and 30: 2BPocket PCSoftware InstallationThe
- Page 31 and 32: Pocket PC Software Installation3. F
- Page 33 and 34: Pocket PCMeters/Graph2CThis chapter
- Page 35 and 36: Pocket PC Meters/GraphStrip ChartTo
- Page 37 and 38: Pocket PC Meters/GraphBar GraphTo b
- Page 39 and 40: Pocket PC Meters/GraphConfiguration
- Page 41 and 42: Pocket PC Meters/GraphResultsThe po
- Page 43 and 44: Pocket PCAutomatic Tests2DTSI TestT
- Page 45 and 46: Pocket PC Automatic TestsHigh RPM T
- Page 47 and 48: Pocket PC Automatic TestsTest Compl
- Page 49 and 50: Pocket PC Automatic TestsCatalyst T
- Page 51 and 52: Pocket PC Automatic Tests5. When pr
- Page 53 and 54: Pocket PC Automatic TestsIf the res
- Page 55 and 56: Pocket PCCustomer/Vehicle2EFGA is d
- Page 57 and 58: Pocket PC Customer/Vehicle✓ To di
- Page 59 and 60: Pocket PC Customer/Vehicle2. Choose
- Page 61 and 62: 2FPocket PC ResultsTest ResultsThe
- Page 63 and 64: Pocket PC ResultsChange StandardsCu
- Page 65: Pocket PCMaintenance2GThis section
- Page 69 and 70: Pocket PC MaintenanceIf the reading
- Page 71 and 72: Pocket PC Maintenance✓ Always mak
- Page 73 and 74: Pocket PC Maintenance3. Remove the
- Page 75 and 76: Pocket PC MaintenanceSetupThis sect
- Page 77 and 78: Pocket PC MaintenanceRPM/Temp Kit
- Page 79 and 80: Pocket PC MaintenanceTSI / Idle Set
- Page 81 and 82: Pocket PC MaintenanceStandardsThe S
- Page 83 and 84: Pocket PC MaintenanceFigure 2G-23:
- Page 85 and 86: Pocket PC MaintenanceBoard Diagnost
- Page 87 and 88: Pocket PC MaintenanceTo perform the
- Page 89 and 90: Pocket PC Maintenance7. Press the S
- Page 91 and 92: Pocket PC MaintenanceFigure 2G-34:
- Page 93 and 94: Pocket PC MaintenanceLow Out FlowTh
- Page 95 and 96: Pocket PCOther Functions2HAboutThis
- Page 97 and 98: 3Using FGA with the PCThe Flexible
- Page 99 and 100: 3APC Software OverviewThe PC versio
- Page 101 and 102: PC Software OverviewCommands 1-10Co
- Page 103 and 104: PC Software OverviewCommandsFigure
- Page 105 and 106: 3BPC SoftwareInstallationThe Flexib
- Page 107 and 108: PC Software Installation5. If this
- Page 109 and 110: 3CPC Meters/Strip ChartThis chapter
- Page 111 and 112: PC Meters/GraphGas Bench MenuThe Ga
- Page 113 and 114: PC Meters/GraphStrip ChartTo view t
- Page 115 and 116: PC Meters/GraphStrip Chart Display
Pocket PC MaintenanceFigure 2G-1: Initial Gas Calibrati<strong>on</strong> Screen3. Verify that the gas analyzer sample system exhaust hose is c<strong>on</strong>nected tothe port labeled Exhaust.4. Disc<strong>on</strong>nect the vehicle exhaust sample hose from the filter bowl.5. Press the Start butt<strong>on</strong> to begin Calibrati<strong>on</strong>.Figure 2G-2: Calibrati<strong>on</strong> Values ScreenThe Calibrati<strong>on</strong> Values screen shown in Figure 2G-2 displays allowing youto verify that the calibrati<strong>on</strong> values being used match the c<strong>on</strong>centrati<strong>on</strong>values of the calibrati<strong>on</strong> bottle. Change the values if necessary.✓ You can change the values <strong>on</strong> this screen by tapping <strong>on</strong> thenumber and editing in place or in Maintenance > Setup > GeneralSetup > Calibrati<strong>on</strong>.2G-2