Operating Instructions - Snap-on Equipment
Operating Instructions - Snap-on Equipment Operating Instructions - Snap-on Equipment
Pocket PC Automatic Tests7. At the completion of the test sequence (warm-up, 2500, idle, 2500) turn offthe engine and remove all probes connected.Figure 2D-15: Catalyst Test Acceptable ScreenAt the end of the test, results are displayed but not stored. Test results can be acceptable(Figure 2D-15), inconclusive (Figure 2D-16), or not acceptable (Figure 2D-17).Figure 2D-16: Catalyst Test Inconclusive Screen2D-10
Pocket PC Automatic TestsIf the results of the first high speed test and second do not agree, perform the testagain or retest the vehicle using the manufacturer’s specific procedure.✓ Always perform the vehicle manufacturer recommended test procedurebefore a catalyst is replaced.Figure 2D-17: Catalyst Test Not Acceptable ScreenIf the results of the two test procedures are not acceptable, the results screendisplays the average values obtained and the standards used to make thedetermination.✓ Always retest using the vehicle manufacturer’s recommendations.MetersSee Manual Meters / Strip Chart / Bar Graph, page 2C-1.TachometerSee Tachometer, page 2C-10.2D-11
- Page 3 and 4: Table of ContentsUsing this Manual
- Page 5 and 6: Table of ContentsManual Meters/Stri
- Page 7: Using this ManualThis manual contai
- Page 10 and 11: Using this ManualSoftware License A
- Page 12 and 13: Safety InformationIMPORTANT SAFETY
- Page 14: Safety InformationFGA SAFETY MESSAG
- Page 17 and 18: Introduction and Equipment Overview
- Page 19 and 20: Introduction and Equipment Overview
- Page 21 and 22: Using FGA with thePocket PC2The Fle
- Page 23 and 24: Pocket PCSoftware Overview2AThe poc
- Page 25 and 26: Pocket PC Software OverviewBattery
- Page 27 and 28: Pocket PC Software OverviewSoftware
- Page 29 and 30: 2BPocket PCSoftware InstallationThe
- Page 31 and 32: Pocket PC Software Installation3. F
- Page 33 and 34: Pocket PCMeters/Graph2CThis chapter
- Page 35 and 36: Pocket PC Meters/GraphStrip ChartTo
- Page 37 and 38: Pocket PC Meters/GraphBar GraphTo b
- Page 39 and 40: Pocket PC Meters/GraphConfiguration
- Page 41 and 42: Pocket PC Meters/GraphResultsThe po
- Page 43 and 44: Pocket PCAutomatic Tests2DTSI TestT
- Page 45 and 46: Pocket PC Automatic TestsHigh RPM T
- Page 47 and 48: Pocket PC Automatic TestsTest Compl
- Page 49 and 50: Pocket PC Automatic TestsCatalyst T
- Page 51: Pocket PC Automatic Tests5. When pr
- Page 55 and 56: Pocket PCCustomer/Vehicle2EFGA is d
- Page 57 and 58: Pocket PC Customer/Vehicle✓ To di
- Page 59 and 60: Pocket PC Customer/Vehicle2. Choose
- Page 61 and 62: 2FPocket PC ResultsTest ResultsThe
- Page 63 and 64: Pocket PC ResultsChange StandardsCu
- Page 65 and 66: Pocket PCMaintenance2GThis section
- Page 67 and 68: Pocket PC Maintenance6. Press OK to
- Page 69 and 70: Pocket PC MaintenanceIf the reading
- Page 71 and 72: Pocket PC Maintenance✓ Always mak
- Page 73 and 74: Pocket PC Maintenance3. Remove the
- Page 75 and 76: Pocket PC MaintenanceSetupThis sect
- Page 77 and 78: Pocket PC MaintenanceRPM/Temp Kit
- Page 79 and 80: Pocket PC MaintenanceTSI / Idle Set
- Page 81 and 82: Pocket PC MaintenanceStandardsThe S
- Page 83 and 84: Pocket PC MaintenanceFigure 2G-23:
- Page 85 and 86: Pocket PC MaintenanceBoard Diagnost
- Page 87 and 88: Pocket PC MaintenanceTo perform the
- Page 89 and 90: Pocket PC Maintenance7. Press the S
- Page 91 and 92: Pocket PC MaintenanceFigure 2G-34:
- Page 93 and 94: Pocket PC MaintenanceLow Out FlowTh
- Page 95 and 96: Pocket PCOther Functions2HAboutThis
- Page 97 and 98: 3Using FGA with the PCThe Flexible
- Page 99 and 100: 3APC Software OverviewThe PC versio
- Page 101 and 102: PC Software OverviewCommands 1-10Co
Pocket PC Automatic TestsIf the results of the first high speed test and sec<strong>on</strong>d do not agree, perform the testagain or retest the vehicle using the manufacturer’s specific procedure.✓ Always perform the vehicle manufacturer recommended test procedurebefore a catalyst is replaced.Figure 2D-17: Catalyst Test Not Acceptable ScreenIf the results of the two test procedures are not acceptable, the results screendisplays the average values obtained and the standards used to make thedeterminati<strong>on</strong>.✓ Always retest using the vehicle manufacturer’s recommendati<strong>on</strong>s.MetersSee Manual Meters / Strip Chart / Bar Graph, page 2C-1.TachometerSee Tachometer, page 2C-10.2D-11