Operating Instructions - Snap-on Equipment
Operating Instructions - Snap-on Equipment Operating Instructions - Snap-on Equipment
Pocket PC Automatic Tests2. Choose Two Speed Idle from the menu.— The TSI Test Preparation screen displays.Figure 2D-2: TSI Test Preparation Screen✓ Abort the test at any time by pressing the Abort button.3. Warm up the engine.4. Put the transmission in neutral or park.5. Turn off all accessories.6. Position the RPM probe (if equipped).7. Press the Continue button.— The Insert Probe screen displays.Figure 2D-3: Prepare for TSI Test Screen8. After the engine reaches operating temperature, insert the exhaust probeinto the tailpipe.9. Select Continue to begin the test.— The TSI High RPM Stage screen displays.2D-2
Pocket PC Automatic TestsHigh RPM Test10. Press the Start Test button.Figure 2D-4: TSI Test High RPM Stage Start Screen11. To begin the test, accelerate the vehicle to the required RPM range asindicated at the top of the screen, 2500 RPM ±10% in this case.— The Time Remaining counter counts down from 30 to 0 (or the numberof seconds set in High Speed Test Length down to 0) as long as RPMis within range.✓ You can access TSI Test Setup to set Test Length, Max RPM andMin RPM from the FGA main screen by pressing Maintenance >Setup > General Setup > TSI/Idle. See TSI / Idle Setup,page 2G-15.Figure 2D-5: TSI Test High RPM Stage Countdown ScreenThe system warns you and the test restarts if:— Low flow is detectedor— Minimum dilution requirements are not met2D-3
- Page 3 and 4: Table of ContentsUsing this Manual
- Page 5 and 6: Table of ContentsManual Meters/Stri
- Page 7: Using this ManualThis manual contai
- Page 10 and 11: Using this ManualSoftware License A
- Page 12 and 13: Safety InformationIMPORTANT SAFETY
- Page 14: Safety InformationFGA SAFETY MESSAG
- Page 17 and 18: Introduction and Equipment Overview
- Page 19 and 20: Introduction and Equipment Overview
- Page 21 and 22: Using FGA with thePocket PC2The Fle
- Page 23 and 24: Pocket PCSoftware Overview2AThe poc
- Page 25 and 26: Pocket PC Software OverviewBattery
- Page 27 and 28: Pocket PC Software OverviewSoftware
- Page 29 and 30: 2BPocket PCSoftware InstallationThe
- Page 31 and 32: Pocket PC Software Installation3. F
- Page 33 and 34: Pocket PCMeters/Graph2CThis chapter
- Page 35 and 36: Pocket PC Meters/GraphStrip ChartTo
- Page 37 and 38: Pocket PC Meters/GraphBar GraphTo b
- Page 39 and 40: Pocket PC Meters/GraphConfiguration
- Page 41 and 42: Pocket PC Meters/GraphResultsThe po
- Page 43: Pocket PCAutomatic Tests2DTSI TestT
- Page 47 and 48: Pocket PC Automatic TestsTest Compl
- Page 49 and 50: Pocket PC Automatic TestsCatalyst T
- Page 51 and 52: Pocket PC Automatic Tests5. When pr
- Page 53 and 54: Pocket PC Automatic TestsIf the res
- Page 55 and 56: Pocket PCCustomer/Vehicle2EFGA is d
- Page 57 and 58: Pocket PC Customer/Vehicle✓ To di
- Page 59 and 60: Pocket PC Customer/Vehicle2. Choose
- Page 61 and 62: 2FPocket PC ResultsTest ResultsThe
- Page 63 and 64: Pocket PC ResultsChange StandardsCu
- Page 65 and 66: Pocket PCMaintenance2GThis section
- Page 67 and 68: Pocket PC Maintenance6. Press OK to
- Page 69 and 70: Pocket PC MaintenanceIf the reading
- Page 71 and 72: Pocket PC Maintenance✓ Always mak
- Page 73 and 74: Pocket PC Maintenance3. Remove the
- Page 75 and 76: Pocket PC MaintenanceSetupThis sect
- Page 77 and 78: Pocket PC MaintenanceRPM/Temp Kit
- Page 79 and 80: Pocket PC MaintenanceTSI / Idle Set
- Page 81 and 82: Pocket PC MaintenanceStandardsThe S
- Page 83 and 84: Pocket PC MaintenanceFigure 2G-23:
- Page 85 and 86: Pocket PC MaintenanceBoard Diagnost
- Page 87 and 88: Pocket PC MaintenanceTo perform the
- Page 89 and 90: Pocket PC Maintenance7. Press the S
- Page 91 and 92: Pocket PC MaintenanceFigure 2G-34:
- Page 93 and 94: Pocket PC MaintenanceLow Out FlowTh
Pocket PC Automatic Tests2. Choose Two Speed Idle from the menu.— The TSI Test Preparati<strong>on</strong> screen displays.Figure 2D-2: TSI Test Preparati<strong>on</strong> Screen✓ Abort the test at any time by pressing the Abort butt<strong>on</strong>.3. Warm up the engine.4. Put the transmissi<strong>on</strong> in neutral or park.5. Turn off all accessories.6. Positi<strong>on</strong> the RPM probe (if equipped).7. Press the C<strong>on</strong>tinue butt<strong>on</strong>.— The Insert Probe screen displays.Figure 2D-3: Prepare for TSI Test Screen8. After the engine reaches operating temperature, insert the exhaust probeinto the tailpipe.9. Select C<strong>on</strong>tinue to begin the test.— The TSI High RPM Stage screen displays.2D-2