Operating Instructions - Snap-on Equipment
Operating Instructions - Snap-on Equipment Operating Instructions - Snap-on Equipment
Introduction and Equipment OverviewFGA Functional DescriptionThis section describes the physical components of the FGA as detailed in Figure1-1.Figure 1-1: FGA Analyzer with Pocket PCA Carrying Handle Sturdy carrying handle for portabilityB Connection Panel Provides electrical interface connectionsC TACH/TEMP Use to connect:RPM kit, part number EAK0213L10AorOil temperature kit, part number EAK0213L12A1-2
Introduction and Equipment OverviewD POWER OUT Connects the internal battery to the Pocket PCMaximum voltage available is 5VDCE RS232 IN Connects the computing device (PC or Pocket PC) to the FGAF RS232 OUT Connects the OBD RPM device to the FGAG USB IN Not used at this time.HUSB Cable ClampFittingSecures USB cable if used.I POWER IN Connects to an external battery (through the cigarette lighter orauto battery clamps) or to the external power supply/chargerJ Cooling Vent Vents the analyzer to maintain acceptable internal temperatureK Component Panel Provides connections for the filter and incoming and outgoinggasesL Cooling Fan Filter Located behind the filter and not shown in this illustration, thecooling fan filter consists of a foam filter covered by a plastic grillM Sample Connection for the vehicle exhaust probe hose.N Exhaust Vents the exhaust gas out of the FGA.✓ For safety a hose must always be connected to the portor the pump will turn off.O Calibration Gas In Connects FGA to the calibration bottle regulatorP Clear Hose Channels gas sample into the FGAQ Water Drain Hose Channels water and residuals out of the filterR Water Trap/ Filter Traps and contains residues and water from exhaust gases toprevent them from entering the analyzer; contains float.The float prevents water from entering the analyzer in the event theunit is tipped over. If this happens, a low flow will occur and thepump may shut down. To correct the problem, release the vacuumand restart the pump.✓ The hose (P) must be removed to release the vacuum inthe system,SPocket PC Case(optional)A storage case for the handheld computer that displays and storestesting data.T ID Plate Contains the following information:Model numberSerial numberVoltage requirementsPatent information/listingsWarning/Information✓ The FGA analyzer does not have an On / Off switch. The analyzer isactivated by communication from the software. If you want the analyzer toperform an action, select the action from the pocket PC or PC software.1-3
- Page 3 and 4: Table of ContentsUsing this Manual
- Page 5 and 6: Table of ContentsManual Meters/Stri
- Page 7: Using this ManualThis manual contai
- Page 10 and 11: Using this ManualSoftware License A
- Page 12 and 13: Safety InformationIMPORTANT SAFETY
- Page 14: Safety InformationFGA SAFETY MESSAG
- Page 19 and 20: Introduction and Equipment Overview
- Page 21 and 22: Using FGA with thePocket PC2The Fle
- Page 23 and 24: Pocket PCSoftware Overview2AThe poc
- Page 25 and 26: Pocket PC Software OverviewBattery
- Page 27 and 28: Pocket PC Software OverviewSoftware
- Page 29 and 30: 2BPocket PCSoftware InstallationThe
- Page 31 and 32: Pocket PC Software Installation3. F
- Page 33 and 34: Pocket PCMeters/Graph2CThis chapter
- Page 35 and 36: Pocket PC Meters/GraphStrip ChartTo
- Page 37 and 38: Pocket PC Meters/GraphBar GraphTo b
- Page 39 and 40: Pocket PC Meters/GraphConfiguration
- Page 41 and 42: Pocket PC Meters/GraphResultsThe po
- Page 43 and 44: Pocket PCAutomatic Tests2DTSI TestT
- Page 45 and 46: Pocket PC Automatic TestsHigh RPM T
- Page 47 and 48: Pocket PC Automatic TestsTest Compl
- Page 49 and 50: Pocket PC Automatic TestsCatalyst T
- Page 51 and 52: Pocket PC Automatic Tests5. When pr
- Page 53 and 54: Pocket PC Automatic TestsIf the res
- Page 55 and 56: Pocket PCCustomer/Vehicle2EFGA is d
- Page 57 and 58: Pocket PC Customer/Vehicle✓ To di
- Page 59 and 60: Pocket PC Customer/Vehicle2. Choose
- Page 61 and 62: 2FPocket PC ResultsTest ResultsThe
- Page 63 and 64: Pocket PC ResultsChange StandardsCu
Introducti<strong>on</strong> and <strong>Equipment</strong> OverviewD POWER OUT C<strong>on</strong>nects the internal battery to the Pocket PCMaximum voltage available is 5VDCE RS232 IN C<strong>on</strong>nects the computing device (PC or Pocket PC) to the FGAF RS232 OUT C<strong>on</strong>nects the OBD RPM device to the FGAG USB IN Not used at this time.HUSB Cable ClampFittingSecures USB cable if used.I POWER IN C<strong>on</strong>nects to an external battery (through the cigarette lighter orauto battery clamps) or to the external power supply/chargerJ Cooling Vent Vents the analyzer to maintain acceptable internal temperatureK Comp<strong>on</strong>ent Panel Provides c<strong>on</strong>necti<strong>on</strong>s for the filter and incoming and outgoinggasesL Cooling Fan Filter Located behind the filter and not shown in this illustrati<strong>on</strong>, thecooling fan filter c<strong>on</strong>sists of a foam filter covered by a plastic grillM Sample C<strong>on</strong>necti<strong>on</strong> for the vehicle exhaust probe hose.N Exhaust Vents the exhaust gas out of the FGA.✓ For safety a hose must always be c<strong>on</strong>nected to the portor the pump will turn off.O Calibrati<strong>on</strong> Gas In C<strong>on</strong>nects FGA to the calibrati<strong>on</strong> bottle regulatorP Clear Hose Channels gas sample into the FGAQ Water Drain Hose Channels water and residuals out of the filterR Water Trap/ Filter Traps and c<strong>on</strong>tains residues and water from exhaust gases toprevent them from entering the analyzer; c<strong>on</strong>tains float.The float prevents water from entering the analyzer in the event theunit is tipped over. If this happens, a low flow will occur and thepump may shut down. To correct the problem, release the vacuumand restart the pump.✓ The hose (P) must be removed to release the vacuum inthe system,SPocket PC Case(opti<strong>on</strong>al)A storage case for the handheld computer that displays and storestesting data.T ID Plate C<strong>on</strong>tains the following informati<strong>on</strong>:Model numberSerial numberVoltage requirementsPatent informati<strong>on</strong>/listingsWarning/Informati<strong>on</strong>✓ The FGA analyzer does not have an On / Off switch. The analyzer isactivated by communicati<strong>on</strong> from the software. If you want the analyzer toperform an acti<strong>on</strong>, select the acti<strong>on</strong> from the pocket PC or PC software.1-3