Operating Instructions - Snap-on Equipment
Operating Instructions - Snap-on Equipment Operating Instructions - Snap-on Equipment
General MaintenanceAs NeededNO x SensorReplace the NO x sensor when calibration fails, indicating a new NO x sensor isneeded. To replace the NO x sensor, contact EquiServ. See New NOx Sensor,page 3G-5.✓ If a warning message appears regarding the NO x cell voltage or lowoutput at the end of the Gas Calibration procedure, the cell may need tobe replaced.O 2 SensorIf the oxygen readings vary widely from what they should be when measuringclean air (20.9%) or the readings do not drop to a low number when testing severalcatalyst-equipped vehicles, then the oxygen sensor may need replacing. Toreplace the O 2 sensor, contact EquiServ.Miscellaneous• Clean the test leads periodically with waterless hand cleaner and wipe dry.• Wipe down the case periodically with a damp cloth.• Inspect all hoses, probes, cables and connections for damage. Replace as needed.✓ Do not use damaged cables.Accessories and OptionsStandardThe FGA analyzer can be purchased in standard configurations with or without apocket PC. Optional accessories are available as listed below.Standard configurations of the FGA analyzer include a version without the pocketPC and a version with the pocket PC. Both versions and the included items aredescribed below.Item
General MaintenanceOptionsPart NumberOptional accessories include the following:ItemEAK0213L10A
- Page 105 and 106: 3BPC SoftwareInstallationThe Flexib
- Page 107 and 108: PC Software Installation5. If this
- Page 109 and 110: 3CPC Meters/Strip ChartThis chapter
- Page 111 and 112: PC Meters/GraphGas Bench MenuThe Ga
- Page 113 and 114: PC Meters/GraphStrip ChartTo view t
- Page 115 and 116: PC Meters/GraphStrip Chart Display
- Page 117 and 118: PC Meters/GraphWhen you select the
- Page 119 and 120: PC Meters/GraphTachometerUse the Ta
- Page 121 and 122: PC Automatic Tests3DTSI TestThis se
- Page 123 and 124: PC Automatic TestsTachometer Config
- Page 125 and 126: PC Automatic TestsIdle RPM TestFGA
- Page 127 and 128: PC Automatic TestsTSI Results16. Th
- Page 129 and 130: 3EPC Customer/VehicleFGA is designe
- Page 131 and 132: PC Customer/VehicleInformation bar
- Page 133 and 134: PC Customer/VehicleWhen the desired
- Page 135 and 136: 3FPC ResultsThe Test Results window
- Page 137 and 138: 3GPC MaintenanceGas CalibrationThis
- Page 139 and 140: PC Maintenance5. Attach the calibra
- Page 141 and 142: PC MaintenanceNew NO x SensorNew NO
- Page 143 and 144: PC MaintenanceShop InformationThe S
- Page 145 and 146: PC MaintenanceThe Setup window cont
- Page 147 and 148: PC MaintenanceTSI Test SetupThe TSI
- Page 149 and 150: PC MaintenanceZero Purge Time(s)—
- Page 151 and 152: PC MaintenanceDiagnosticsService ut
- Page 153 and 154: PC Other Functions3HThis chapter co
- Page 155: 4General MaintenanceThis chapter ad
- Page 159 and 160: General Maintenance3. Select the Ig
- Page 161 and 162: General MaintenanceWhen using the O
- Page 163 and 164: General Maintenance—Push the gray
- Page 165 and 166: General MaintenanceWhen FGA softwar
- Page 167 and 168: 5InterpretationThe section includes
- Page 169 and 170: Interpretation• Minimal NO is pro
- Page 171 and 172: Interpretation2. Repair the vehicle
- Page 173 and 174: Interpretation:The following is a c
- Page 175 and 176: AAppendix A:OBD II ConnectionsThe l
- Page 177 and 178: LIMITED WARRANTYTERMS AND CONDITION
General MaintenanceOpti<strong>on</strong>sPart NumberOpti<strong>on</strong>al accessories include the following:ItemEAK0213L10A <str<strong>on</strong>g>Snap</str<strong>on</strong>g>-<strong>on</strong> RPM Kit (See Using the Opti<strong>on</strong>al RPM Kit, page 4-3)Includes:AL 410-0139AL 410-0216AL 410-0212AL 410-0407AL 413-0406OBD II diagnostic interface10' DB9 male to DB9 female adapter cable12' Yellow RPM extender cableRFI RPM probe with 15' cableNumber <strong>on</strong>e cylinder inductive pick-up clamp with 6' cableEAK0213L12A<str<strong>on</strong>g>Snap</str<strong>on</strong>g>-<strong>on</strong> FGA Temperature Kit (See Using the Opti<strong>on</strong>al Oil Temperature Kit,page 4-7)Includes:AL 410-0403AL 410-0413AL 410-041420' cable with temperature probeY-c<strong>on</strong>nector adapter12' Y-c<strong>on</strong>nector extensi<strong>on</strong> cableEAK0213L11A<str<strong>on</strong>g>Snap</str<strong>on</strong>g>-<strong>on</strong> FGA Calibrati<strong>on</strong> Kit without Gas (Also used with MODIS)Includes:AL 210-015215 psi Regulator with 3' hoseEEEA300ASWEEEA301ASWPC Software for Flexible Gas AnalyzerIncludes:AL 490-0403 Flexible Gas Analyzer Software <strong>on</strong> CD-ROMAL 610-0011 25' RS232 PC cable (DB9 Female to DB9 Female)Pocket PC Software OnlyIncludes:AL 490-0403 Flexible Gas Analyzer Software (<strong>on</strong>e CD-ROM)AL 410-0412 6" Yellow Pocket PC Power CableAL 410-0217 iPAQ Series 3800 Serial and Power Cable for Pocket PCAL 490-0403 FGA iPAQ CardC<strong>on</strong>tact your <str<strong>on</strong>g>Snap</str<strong>on</strong>g>-<strong>on</strong> Sales Representative for complete details and informati<strong>on</strong>.Using the Opti<strong>on</strong>al RPM KitThe opti<strong>on</strong>al RPM kit can be used with the pocket PC or desktop/laptop PCsoftware packages. The RPM kit c<strong>on</strong>tains three individual RPM probes that allowyou to obtain RPMs from most vehicles. Under some c<strong>on</strong>diti<strong>on</strong>s certain vehicleswill not provide a stable RPM signal independent of which method is used toattempt to obtain RPM.4-3