Operating Instructions - Snap-on Equipment
Operating Instructions - Snap-on Equipment Operating Instructions - Snap-on Equipment
PC Automatic TestsHigh RPM Test8. The TSI Test begins with the 2500 RPM Test.Figure 3D-4: TSI Simulation Test at 2500 RPM✓ The software sets all minimum RPM requirements to 0 when theDisable RPM box is checked.9. To begin the test, accelerate the vehicle to the required RPM range asindicated below the slide meter, 2500 ± 10%.— Before the simulation begins, a test initialization occurs. Testinitialization is completed when the vehicle maintains the RPM range,low flow is not detected, and the minimum dilution requirements aremet for a period of two consecutive seconds (or to the setting for TimeRequired Inside Initialization).10. When test initialization is complete, maintain acceleration within the RPMrange using the slide meter and digital meter.— The Time counter, located in the upper left meter, counts down from30 to 0 (or the number of seconds set in High Idle RPM Time down to0) as long as RPM is within range, low flow is not detected, andminimum dilution requirements are met.The system warns you and the test restarts if:— Low flow is detected,or— Minimum dilution requirements are not met,or— RPM values are outside the range for more than two consecutive seconds(or the time set in Time Allowed Outside RPM Range), or a total of tenseconds (or the number set in Total Time Allowed Outside RPM Range).3D-4
PC Automatic TestsIdle RPM TestFGA allows a maximum of three restarts (or the number set in MaxRestarts). A fourth restart (or the number in Max Restarts+1) causes theTSI Test to abort.✓ Select the Tachometer button at any time to reconfigure thetachometer. The test then restarts.✓ Press the Abort button at any time to stop the test.When the 2500 RPM Test is complete, the idle RPM Test begins.Figure 3D-5: TSI Simulation Test at Idle RPM11. To begin the idle phase of the test, accelerate the vehicle to the RPMrange indicated below the slide meter, 450–1300 in this case.— Before the simulation begins, a test initialization occurs. Testinitialization is complete when the vehicle maintains the RPM range,low flow is not detected, and the minimum dilution requirements aremet for a period of two consecutive seconds (or to the setting for TimeRequired Inside Initialization).12. When test initialization is complete, maintain acceleration within the RPMrange using the slide meter and digital meter.— The Time counter, located in the upper left meter, counts down from30 to 0 (or the number of seconds set in Idle RPM Time down to 0) aslong as RPM is within range, low flow is not detected, and minimumdilution requirements are met.3D-5
- Page 73 and 74: Pocket PC Maintenance3. Remove the
- Page 75 and 76: Pocket PC MaintenanceSetupThis sect
- Page 77 and 78: Pocket PC MaintenanceRPM/Temp Kit
- Page 79 and 80: Pocket PC MaintenanceTSI / Idle Set
- Page 81 and 82: Pocket PC MaintenanceStandardsThe S
- Page 83 and 84: Pocket PC MaintenanceFigure 2G-23:
- Page 85 and 86: Pocket PC MaintenanceBoard Diagnost
- Page 87 and 88: Pocket PC MaintenanceTo perform the
- Page 89 and 90: Pocket PC Maintenance7. Press the S
- Page 91 and 92: Pocket PC MaintenanceFigure 2G-34:
- Page 93 and 94: Pocket PC MaintenanceLow Out FlowTh
- Page 95 and 96: Pocket PCOther Functions2HAboutThis
- Page 97 and 98: 3Using FGA with the PCThe Flexible
- Page 99 and 100: 3APC Software OverviewThe PC versio
- Page 101 and 102: PC Software OverviewCommands 1-10Co
- Page 103 and 104: PC Software OverviewCommandsFigure
- Page 105 and 106: 3BPC SoftwareInstallationThe Flexib
- Page 107 and 108: PC Software Installation5. If this
- Page 109 and 110: 3CPC Meters/Strip ChartThis chapter
- Page 111 and 112: PC Meters/GraphGas Bench MenuThe Ga
- Page 113 and 114: PC Meters/GraphStrip ChartTo view t
- Page 115 and 116: PC Meters/GraphStrip Chart Display
- Page 117 and 118: PC Meters/GraphWhen you select the
- Page 119 and 120: PC Meters/GraphTachometerUse the Ta
- Page 121 and 122: PC Automatic Tests3DTSI TestThis se
- Page 123: PC Automatic TestsTachometer Config
- Page 127 and 128: PC Automatic TestsTSI Results16. Th
- Page 129 and 130: 3EPC Customer/VehicleFGA is designe
- Page 131 and 132: PC Customer/VehicleInformation bar
- Page 133 and 134: PC Customer/VehicleWhen the desired
- Page 135 and 136: 3FPC ResultsThe Test Results window
- Page 137 and 138: 3GPC MaintenanceGas CalibrationThis
- Page 139 and 140: PC Maintenance5. Attach the calibra
- Page 141 and 142: PC MaintenanceNew NO x SensorNew NO
- Page 143 and 144: PC MaintenanceShop InformationThe S
- Page 145 and 146: PC MaintenanceThe Setup window cont
- Page 147 and 148: PC MaintenanceTSI Test SetupThe TSI
- Page 149 and 150: PC MaintenanceZero Purge Time(s)—
- Page 151 and 152: PC MaintenanceDiagnosticsService ut
- Page 153 and 154: PC Other Functions3HThis chapter co
- Page 155 and 156: 4General MaintenanceThis chapter ad
- Page 157 and 158: General MaintenanceOptionsPart Numb
- Page 159 and 160: General Maintenance3. Select the Ig
- Page 161 and 162: General MaintenanceWhen using the O
- Page 163 and 164: General Maintenance—Push the gray
- Page 165 and 166: General MaintenanceWhen FGA softwar
- Page 167 and 168: 5InterpretationThe section includes
- Page 169 and 170: Interpretation• Minimal NO is pro
- Page 171 and 172: Interpretation2. Repair the vehicle
- Page 173 and 174: Interpretation:The following is a c
PC Automatic TestsHigh RPM Test8. The TSI Test begins with the 2500 RPM Test.Figure 3D-4: TSI Simulati<strong>on</strong> Test at 2500 RPM✓ The software sets all minimum RPM requirements to 0 when theDisable RPM box is checked.9. To begin the test, accelerate the vehicle to the required RPM range asindicated below the slide meter, 2500 ± 10%.— Before the simulati<strong>on</strong> begins, a test initializati<strong>on</strong> occurs. Testinitializati<strong>on</strong> is completed when the vehicle maintains the RPM range,low flow is not detected, and the minimum diluti<strong>on</strong> requirements aremet for a period of two c<strong>on</strong>secutive sec<strong>on</strong>ds (or to the setting for TimeRequired Inside Initializati<strong>on</strong>).10. When test initializati<strong>on</strong> is complete, maintain accelerati<strong>on</strong> within the RPMrange using the slide meter and digital meter.— The Time counter, located in the upper left meter, counts down from30 to 0 (or the number of sec<strong>on</strong>ds set in High Idle RPM Time down to0) as l<strong>on</strong>g as RPM is within range, low flow is not detected, andminimum diluti<strong>on</strong> requirements are met.The system warns you and the test restarts if:— Low flow is detected,or— Minimum diluti<strong>on</strong> requirements are not met,or— RPM values are outside the range for more than two c<strong>on</strong>secutive sec<strong>on</strong>ds(or the time set in Time Allowed Outside RPM Range), or a total of tensec<strong>on</strong>ds (or the number set in Total Time Allowed Outside RPM Range).3D-4