Infinity Operations Manual (96402,96403, 96406, 96407) - Whip Mix

More documents

Recommendations

Info

FIELD SERVICEREPLACEMENT OF HEATING PLATESTurn off the power to the oven, unplug the power cord,remove trays from the muffle chamber and insure thatthe oven is cool.Remove the upper back cover.On the rear of the unit remove the nuts that hold theheater plate wires to the ceramic terminals. Removeall hardware and wires from the terminals. Discardany burnt hardware and replace with hardware piecesshipped with the heater plates. Retain hardware forlater use. Straighten the wires for smoother removalof the plates.Straighten thermocouple at the bend and removebushings from heater plate wires.Move heater wires and thermocouple out of the upperhousing to allow insulation to slide out the back of theunit.From the front of the muffle chamber with the door openpush the entire insulation chamber out the back of unitand place on a table.Remove ceramic front plates from muffle insulation andplace aside.Place the new plates in the chamber, if back plates arebeing replaced as well they must be installed first, alsoinsure that the wires are bent up so they will slide intothe back.If the back plates are being replaced the filler stripshould be replaced as well. A new strip was shipped withthe plates.Side HeatingPlate Assembly(2)Insulating StripCeramic Insulating BushingsRear HeatingPlate LeadsOnce the plates are installed place the insulation chamberback inside the oven and wire the terminals according tothe model and voltage in the pictures on the next page:When wiring the plates insure that between each wirea flat washer is placed. See picture below.Flat WasherRear HeatingPlate LeadsCeramic FrontsHeater JumperNutLock WasherFrom here the plates can be removed by pulling themout the front of the insulation. The Large models haveback plates and side plates, while the Medium modelhas only side plates.Flat WasherNutLock WasherNote: Place flat washer between each wire.After the heater plates are wired, replace the upper backcover and bottom cover. Insure that the oven heats byrunning a program.21
Figure 4INFINITY WITH UPPER REAR PANEL REMOVEDJumperHeating Plate WirePower TerminalRear Insulating PanelThermocoupleCeramic InsulatingBushingHeater (Power) LeadsINFINITY- M30 115VJumperRear Insulating PanelHeating Plate WirePower TerminalThermocoupleCeramic InsulatingBushingHeater (Power) LeadsINFINITY- L30 115VHeating Plate WireRear Insulating PanelPower TerminalThermocoupleCeramic InsulatingBushingHeater (Power) LeadsINFINITY- L30 230V22
Page 2 and 3: TABLE OF CONTENTSIntroduction .....
Page 4 and 5: SPECIFICATIONSINFINITY MElectrical
Page 6 and 7: PROGRAMkey parts identification and
Page 8 and 9: installationunpack and set-up1. Unp
Page 11 and 12: operationprogram and operate - TWO
Page 13 and 14: operationprogram and operate - four
Page 15 and 16: OPERATIONedit while a program is ru
Page 17 and 18: OPERATIONSample three stage program
Page 19 and 20: ERROR CODESerrorcode DESCRIPTION PR
Page 21: SERVICE6. When the tablet begins to
Page 25 and 26: Figure 5INFINITY WIRING DIAGRAM24
Page 27 and 28: FIELD SERVICEREPLACEMENT OF THE SSR
Page 29 and 30: SPARE PARTS LISTSPARE PARTS FOR INF
Page 31 and 32: PROGRAM CARD FORMSProgram #Metal(s)

Infinity Operations Manual (96402,96403, 96406, 96407) - Whip Mix

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?