Manual - EDAN USA
Manual - EDAN USA Manual - EDAN USA
H100B Pulse Oximeter User Manual• The sensor is applied to the patient;• The patient’s SpO 2 , Pulse rate are beingreported;• No error conditions exist.4 Wash the probe with clean water afterdisinfecting it to remove any remaining solution.The probe can only be reused after driedthoroughly.5 Do not disinfect the probe with the water boiled.6 Any residue should be removed from the probebefore being disinfected, and avoid contactingcorrosive solvent. Dipping the cable into alcoholor alkalescent solvent for a long time mayreduce the flexibility of the scarfskin of the cable.Also, the connector should not be dipped.7 After monitoring, disinfect the probe accordingto the instruction described in the user manual.8 The materials with which the patient or anyother person can come into contact conformwith the standard of ISO10993.9 The pictures and interfaces in this manual arefor reference only.- 10 -
H100B Pulse Oximeter User Manual10 A functional tester cannot be used to assessthe accuracy of the pulse oximeter probe or thepulse oximeter monitor.11 If there is independent demonstration that theparticular calibration curve is accurate for thecombination of a pulse oximeter monitor and apulse oximeter probe, then a functional testercan measure the contribution of a monitor to thetotal error of a monitor/probe system. Thefunctional tester can then measure howaccurately a particular pulse oximeter monitor isreproducing that calibration curve.12 The operating time of the Ni-MH rechargeablebattery package depends on the configurationand operation of the pulse oximeter.1.4 Symbols in the OximeterThis symbol indicates that theinstrument is IEC/EN 60601-1Type BF equipment.- 11 -
- Page 2 and 3: About this ManualP/N: 21.54.109000-
- Page 4 and 5: qualified technician to maintain an
- Page 6 and 7: 3.3 System Menu ...................
- Page 8 and 9: A1.1 Classification................
- Page 10 and 11: H100B Pulse Oximeter User Manualsen
- Page 12 and 13: H100B Pulse Oximeter User Manualfal
- Page 14 and 15: H100B Pulse Oximeter User Manualman
- Page 16 and 17: H100B Pulse Oximeter User Manualwas
- Page 21 and 22: H100B Pulse Oximeter User ManualThe
- Page 23 and 24: H100B Pulse Oximeter User ManualFig
- Page 25 and 26: H100B Pulse Oximeter User ManualSpO
- Page 28 and 29: or off the backlight.H100B Pulse Ox
- Page 30 and 31: H100B Pulse Oximeter User Manualthe
- Page 32 and 33: H100B Pulse Oximeter User Manual1 R
- Page 34 and 35: H100B Pulse Oximeter User ManualChe
- Page 36 and 37: H100B Pulse Oximeter User ManualQua
- Page 38 and 39: H100B Pulse Oximeter User ManualRS2
- Page 40 and 41: H100B Pulse Oximeter User ManualFig
- Page 42 and 43: H100B Pulse Oximeter User ManualArr
- Page 44 and 45: H100B Pulse Oximeter User ManualMan
- Page 46 and 47: H100B Pulse Oximeter User ManualFig
- Page 48 and 49: H100B Pulse Oximeter User ManualPul
- Page 50 and 51: H100B Pulse Oximeter User ManualA d
- Page 52 and 53: H100B Pulse Oximeter User Manualsys
- Page 54 and 55: H100B Pulse Oximeter User Manuallim
- Page 56 and 57: H100B Pulse Oximeter User ManualAft
- Page 58 and 59: H100B Pulse Oximeter User Manual3.3
- Page 60 and 61: H100B Pulse Oximeter User Manual4 A
- Page 62 and 63: H100B Pulse Oximeter User ManualUnc
- Page 64 and 65: H100B Pulse Oximeter User Manualgiv
- Page 66 and 67: H100B Pulse Oximeter User Manual5 P
H100B Pulse Oximeter User <strong>Manual</strong>10 A functional tester cannot be used to assessthe accuracy of the pulse oximeter probe or thepulse oximeter monitor.11 If there is independent demonstration that theparticular calibration curve is accurate for thecombination of a pulse oximeter monitor and apulse oximeter probe, then a functional testercan measure the contribution of a monitor to thetotal error of a monitor/probe system. Thefunctional tester can then measure howaccurately a particular pulse oximeter monitor isreproducing that calibration curve.12 The operating time of the Ni-MH rechargeablebattery package depends on the configurationand operation of the pulse oximeter.1.4 Symbols in the OximeterThis symbol indicates that theinstrument is IEC/EN 60601-1Type BF equipment.- 11 -