HM 1400 TRX Total Mercury Analyser - Webshop, Gas Analysis ...

More documents

Recommendations

Info

5. Installation5.4.2 Power supply (preferably 230 V - 3/N/PE)WARNINGDanger from electrical equipmentDanger from electric shocksBefore removing the housing or accidental-contact protection, the equipmentmust be disconnected from the power supply.If it cannot be disconnected, protective equipment must be worn to ensure theprevention of electric shocks.A fixed energy supply connection must be established to the measuringdevice. The mains cable is connected to a residual current protective device for230 V / 50 Hz, 25 A / 30 mA in the device cabinet. The customer fuse protectionfor the energy connection must be designed accordingly.5.4.3 Measuring and operating data recordingThe interface lines for measuring values, control signals and operating anderror status messages agreed in the project must be provided by thecustomer. The terminal assignment can be found in the circuit diagrams.Attention! Before connecting the signal line for the measuring signal, the wirejumper at terminal X3 between contacts 16 and 17 (also 18 and 19 if thesecond measuring signal output is used) must be removed. The signal line isthen attached to the same terminal points.5.4.4 Exhaust gasWhen the gas sample has passed through the device and been analysed, itexits the device's gas duct. Depending on the project, this exhaust gas canalso be conveyed to its destination via a hose connection in the device roof.Once again, a bulkhead fitting with hose connection for DN 4/6 on both sidesserves for connection to a simple plastic hose, which in turn is led directly tothe destination or to a central exhaust gas system.5.4.5 CondensateThe condensate resulting from the gas drying phase is now pumped out of themeasuring device by a hose pump. The approx. 1.50 m long transparentcondensate hose end (DN 4/6) is led out through the side wall of themeasuring device. It is now possible to connect the hose end directly to thecondensate receptacle or to a central condensate collecting system. If thecondensate receptacle with level monitoring is used, you must ensure that thecables for the signal connection between level sensor and measuring deviceare installed according to the terminal plan.Generally the condensate receptacle is housed in the device cabinet.WARNINGCondensate fluid: Risk of skin irritationCondensate can give rise to specific dangers. These are dependent on thepollutants contained in the measuring gas. The receptacle must thereforealways be handled by appropriately trained personnel with the necessary careand with any required protective equipment.44 HM 1400 TRX
HM 1400 TRXTotal Mercury Analyser066 Operation6.1 Commissioning with default parameters6.2 Standby phase6.3 Measuring mode
Page 2 and 3: Translation of original operating i
Page 4 and 5: Table of contents5.4.5 Condensate .
Page 7: 0. Foreword0 ForewordThe purpose of
Page 11 and 12: 1. General1 GeneralWe hope that our
Page 13 and 14: 1. General1.3 Limitation of liabili
Page 15: HM 1400 TRXTotal Mercury Analyser02
Page 18 and 19: 2. SafetyGeneral warning symbolElec
Page 20 and 21: 2. SafetySafety shoesto protect aga
Page 22 and 23: 2. Safety2.7 Hazard from chemicalsC
Page 24 and 25: 2. Safety• Knowledge of system co
Page 34 and 35: 4. Theoretical foundationsother com
Page 36 and 37: 4. Theoretical foundationsdisplay v
Page 38 and 39: 4. Theoretical foundationsThe coole
Page 47 and 48: 6. Operation6 Operation6.1 Commissi
Page 52 and 53: 7. OperationKey functions:Special k
Page 54 and 55: 7. Operation• Menu item "PASSWORD
Page 56 and 57: 7. OperationFigure 7.4 The Main men
Page 58 and 59: 7. Operation• Menu item "Systemst
Page 60 and 61: 7. Operation• Menu item "Measurin
Page 62 and 63: 7. Operation7.4 Zero offset (automa
Page 64 and 65: 7. OperationIf the key is pressed a
Page 71 and 72: 8. Measuring device check (option)8
Page 73: HM 1400 TRXTotal Mercury AnalyserAp
Page 76 and 77: 10. Appendix:Device parameters in d
Page 78 and 79: 11. Appendix:Maintenance11 Appendix
Page 80 and 81: 11. Appendix:MaintenanceThis mainte
Page 82 and 83: 12. Appendix: Error messages and th
Page 84 and 85: 12. Appendix: Error messages and th
Page 86 and 87: 13. Order numbers for replacement a
Page 88 and 89: Designation Order no. Order no.Incl
Page 90 and 91: 14. Appendix Extracts from safety d
Page 92 and 93: 14. Appendix Extracts from safety d
Page 94 and 95:
14. Appendix Extracts from safety d
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
15. Index15 Index3-W-V 59Accidents
Page 107 and 108:
16. DURAG GROUP company addresses16
show all

HM 1400 TRX Total Mercury Analyser - Webshop, Gas Analysis ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?