Using a VNXe System with Microsoft Windows Hyper-V - EMC ...
Using a VNXe System with Microsoft Windows Hyper-V - EMC ... Using a VNXe System with Microsoft Windows Hyper-V - EMC ...
Setting Up a Host to Use VNXe Hyper-V StorageThe Discover Target Portal dialog box opens.4. In the Discover Target Portal dialog box:a. Enter the IP address of the VNXe iSCSI Server interface on the first subnet with thehost interface.You can find this address with Unisphere by selecting Settings > iSCSI ServerSettings.b. Click Advanced.The Advanced Settings dialog box opens.5. In the Advanced Settings dialog box, set the following:• Local adapter to Microsoft iSCSI Initiator.• Initiator IP to the IP address of the host interface on the first subnet with the VNXeiSCSI Server interface.6. If the host initiator is configured for optional initiator CHAP on the VNXe iSCSI Server:a. Select Enable CHAP logon.b. Leave Name as the default value, which is the initiator’s IQN.c. Set Target secret to the same secret that is configured for the host initiator on theVNXe iSCSI Server.The VNXe iSCSI Servers support CHAP secrets of 12 to 16 characters only.d. If the VNXe iSCSI Server is configured for mutual CHAP, select Perform MutualAuthentication.7.Click OK to close the Advanced Settings dialog box.8. In the Discover Target Portal dialog box, enter the IP address of the VNXe iSCSI Serverinterface on the first subnet with the host interface.You can find this address with Unisphere by selecting Settings > iSCSI Server Settings.9. Click OK to close the Discover Target Portal dialog box.10. In the Discovery tab, verify the address of the first VNXe iSCSI Server interface appearsin the Target Portals list.11. Click Discover Portal again to configure the second VNXe iSCSI Server interface.12. In the Discover Target Portal dialog box:a. Enter the IP address of the VNXe iSCSI Server interface on the second subnet withthe host interface.You can find this address with Unisphere by selecting Settings > iSCSI ServerSettings.b. Click Advanced.The Advanced Settings dialog box opens.13. In the Advanced Settings dialog box, set the following:• Local adapter to Microsoft iSCSI Initiator.32 Using a VNXe System with Microsoft Windows Hyper-V
Setting Up a Host to Use VNXe Hyper-V Storage• Initiator IP to the IP address of the host interface on the second subnet with theVNXe iSCSI Server interface.14. If the host initiator is configured for optional initiator CHAP on the VNXe iSCSI Server:a. Select Enable CHAP logon.b. Leave Name as the default value, which is the initiator’s IQN.c. Set Target secret to the same secret that is configured for the host initiator on theVNXe iSCSI Server.The VNXe iSCSI Servers support CHAP secrets of 12 to 16 characters only.d. If the VNXe iSCSI Server is configured for mutual CHAP, select Perform MutualAuthentication.15. Click OK to close the Advanced Settings dialog box.16. In the Discover Target Portal dialog box, enter the IP address of the VNXe iSCSI Serverinterface on the second subnet with the host interface.17. Click OK to close the Discover Target Portal dialog box.18. In the Discovery tab, verify that the addresses of both the VNXe iSCSI Server interfacesappear in the Target Portals list.19. Click the Targets tab.20. In the Targets tab under Discovered Targets, select the VNXe iSCSI Server and clickConnect.The Connect to Target dialog box opens.21. In the Connect to Target dialog box:a. Verify that Add this connection to the list of Favorite Targets is selected.b. Verify that Enable Multi-path is not selected.c. Click Advanced.The Advanced Settings dialog box opens.22. In the Advanced Settings dialog box, set the following:• Local adapter to Microsoft iSCSI Initiator.• Source IP to the address of the host interface on the first subnet with the VNXeiSCSI Server interface.• Target Portal to the address of the VNXe iSCSI Server interface on the first subnetwith the host interface.You can find this address with Unisphere by selecting Settings > iSCSI ServerSettings.23. Click OK to close the Advanced Settings dialog box.24. Click OK to close the Connect to Target dialog box.25. In the Targets tab, select the VNXe iSCSI target, and click Properties.The Properties dialog box opens.Configuring the host to connect to a VNXe iSCSI Server 33
- Page 1: EMC ® VNXe SeriesUsing a VNXe Sys
- Page 4 and 5: Contents4 Using a VNXe System with
- Page 7 and 8: PrefaceCourierUsed for:• System o
- Page 9 and 10: CHAPTER 1Setting Up a Host to Use V
- Page 11 and 12: Setting Up a Host to Use VNXe Hyper
- Page 13: Setting Up a Host to Use VNXe Hyper
- Page 16 and 17: Setting Up a Host to Use VNXe Hyper
- Page 18 and 19: Setting Up a Host to Use VNXe Hyper
- Page 20 and 21: Setting Up a Host to Use VNXe Hyper
- Page 23 and 24: Setting Up a Host to Use VNXe Hyper
- Page 25 and 26: Setting Up a Host to Use VNXe Hyper
- Page 27 and 28: Setting Up a Host to Use VNXe Hyper
- Page 29 and 30: Setting Up a Host to Use VNXe Hyper
- Page 31: Setting Up a Host to Use VNXe Hyper
- Page 35 and 36: Setting Up a Host to Use VNXe Hyper
- Page 37 and 38: Setting Up a Host to Use VNXe Hyper
- Page 39 and 40: Setting Up a Host to Use VNXe Hyper
- Page 41 and 42: Setting Up a Host to Use VNXe Hyper
- Page 43 and 44: CHAPTER 2Migrating Hyper-V Virtual
- Page 45 and 46: Migrating Hyper-V Virtual Machines
- Page 47 and 48: APPENDIX ASetting Up MPIO for a Win
- Page 49 and 50: Setting Up MPIO for a Windows Hyper
- Page 51 and 52: Setting Up MPIO for a Windows Hyper
Setting Up a Host to Use <strong>VNXe</strong> <strong>Hyper</strong>-V StorageThe Discover Target Portal dialog box opens.4. In the Discover Target Portal dialog box:a. Enter the IP address of the <strong>VNXe</strong> iSCSI Server interface on the first subnet <strong>with</strong> thehost interface.You can find this address <strong>with</strong> Unisphere by selecting Settings > iSCSI ServerSettings.b. Click Advanced.The Advanced Settings dialog box opens.5. In the Advanced Settings dialog box, set the following:• Local adapter to <strong>Microsoft</strong> iSCSI Initiator.• Initiator IP to the IP address of the host interface on the first subnet <strong>with</strong> the <strong>VNXe</strong>iSCSI Server interface.6. If the host initiator is configured for optional initiator CHAP on the <strong>VNXe</strong> iSCSI Server:a. Select Enable CHAP logon.b. Leave Name as the default value, which is the initiator’s IQN.c. Set Target secret to the same secret that is configured for the host initiator on the<strong>VNXe</strong> iSCSI Server.The <strong>VNXe</strong> iSCSI Servers support CHAP secrets of 12 to 16 characters only.d. If the <strong>VNXe</strong> iSCSI Server is configured for mutual CHAP, select Perform MutualAuthentication.7.Click OK to close the Advanced Settings dialog box.8. In the Discover Target Portal dialog box, enter the IP address of the <strong>VNXe</strong> iSCSI Serverinterface on the first subnet <strong>with</strong> the host interface.You can find this address <strong>with</strong> Unisphere by selecting Settings > iSCSI Server Settings.9. Click OK to close the Discover Target Portal dialog box.10. In the Discovery tab, verify the address of the first <strong>VNXe</strong> iSCSI Server interface appearsin the Target Portals list.11. Click Discover Portal again to configure the second <strong>VNXe</strong> iSCSI Server interface.12. In the Discover Target Portal dialog box:a. Enter the IP address of the <strong>VNXe</strong> iSCSI Server interface on the second subnet <strong>with</strong>the host interface.You can find this address <strong>with</strong> Unisphere by selecting Settings > iSCSI ServerSettings.b. Click Advanced.The Advanced Settings dialog box opens.13. In the Advanced Settings dialog box, set the following:• Local adapter to <strong>Microsoft</strong> iSCSI Initiator.32 <strong>Using</strong> a <strong>VNXe</strong> <strong>System</strong> <strong>with</strong> <strong>Microsoft</strong> <strong>Windows</strong> <strong>Hyper</strong>-V
Change language