Standard range - Belting Ware

More documents

Recommendations

Info

Timing pulleys Recommended special constructions Construction OB Construction EB Construction ZB Construction OBN Construction EBN Construction ZBN Materials Steel, grey cast iron, aluminium; other materials available on request Do NOT use cast iron for speeds > 30 m/s anymore! Bores All timing pulleys are pilot bored. On request they can be finish bored to DIN H7 tolerance. Explanation of the abbreviations OB = without flanges EB = one flange ZB = two flanges OBN = without flanges, with hub EBN = one flange, with hub ZBN = two flanges, with hub 63
Permissible variation in tooth pitch The permissible variations in tooth pitch between two consecutive teeth and for the sum of the variations within a 90° arc of a pulley are shown in the following table. These tolerances indicate the distance between the corresponding points on the right or the left flank of consecutive teeth. 64 Outside diameter d a [mm] ≤ 25 > 25 ≤ 50 > 50 ≤ 100 > 100 ≤ 175 > 175 ≤ 300 > 300 ≤ 500 > 500 Outside diameter da Permissible variation [mm] [mm] ≤ 25 > 25 ≤ 50 > 50 ≤ 100 > 100 ≤ 175 > 175 ≤ 300 > 300 ≤ 500 > 500 between two consecutive teeth Permissible variation in tooth pitch [mm] Permissible variation of the outside diameter Timing pulleys Dimensions and tolerances + 0.05 0 + 0.07 0 + 0.10 0 + 0.13 0 + 0.15 0 + 0.18 0 + 0.20 0 sum within a 90° arc 0.03 0.06 0.03 0.09 0.03 0.10 0.03 0.13 0.03 0.15 0.03 0.18 0.03 0.20 Pulley width Type Pulley Nominal Smallest pulley width width pulley with without designation width flanges b f* flanges [mm] [mm] [mm] [mm] 3 M 6 6 7 9 9 9 10 12 15 15 17 19 5 M 9 9 10 12 15 15 17 19 25 25 27 29 8 M 20 20 22 26 30 30 34 38 50 50 54 58 85 85 90 94 14 M 40 40 47 54 55 55 63 70 85 85 95 102 115 115 126 133 170 170 180 187 *b f = Pulley width between the flanges Note The minimum width b for pulleys without flanges can be reduced, if there is no side wobble or run out; however, it may not fall below the minimum width bf for pulleys with flanges. Axial run out tolerance Outside diameter Maximum overall <strong>range</strong> [mm] fluctuation [mm] ≤ 100 0.10 > 100 0.01 mm per 10 mm ≤ 250 outside diameter 0.25 mm + 0.0005 mm > 250 per mm outside diameter over 250.00 mm Tolerance of eccentricity Outside diameter Maximum overall <strong>range</strong> [mm] fluctuation [mm] ≤ 200 0.10 > 200 0.0005 mm per 10 mm outside diameter, but not exceeding the tolerance for the outside diameter
Page 1 and 2:
NEW OMEGA HL OMEGA 5M HP FOR DRIVES
Page 3 and 4:
Produktionsstätten und Vertriebsor
Page 5 and 6:
4 Properties of optibelt OMEGA timi
Page 7 and 8:
Construction 6 Top surface Tension
Page 9 and 10:
8 Belt designation Order example: S
Page 11 and 12:
Top surface A durable and flexible
Page 13 and 14: Order example: Timing belts: Optibe
Page 15 and 16: Order example: 14 Belt designation
Page 17 and 18: Construction 16 Product description
Page 19 and 20: 18 111 3M 111 37 129 3M 129 43 141
Page 21 and 22: Order example: Timing belts: Optibe
Page 23 and 24: 22 Calculation optibelt OMEGA HL/HP
Page 25 and 26: Diagram 2 Speed of the small timing
Page 27 and 28: Total service faktor c 2 26 Calcula
Page 29 and 30: Prime mover Electric motor 50 Hz St
Page 31 and 32: 30 Calculation optibelt OMEGA HL/HP
Page 33 and 34: 32 Speed of the small timing pulley
Page 45 and 46: 44 Number of teeth 10 9.55 8.79 11
Page 47 and 48: 46 Number of teeth Standard timing
Page 49 and 50: 48 optibelt ZRS HTD ® timing pulle
Page 51 and 52: optibelt ZRS HTD ® timing pulleys
Page 59 and 60: Taper bush 58 optibelt ZRS HTD ® t
Page 61 and 62: Taper bush 60 optibelt ZRS HTD ® t
Page 63: Bore diameter d 2 (mm) Tightening t
Page 67 and 68: Flanged pulleys For the guidance of
Page 69 and 70: 68 Design hints Problems - Causes -
Page 71 and 72: Details of the drive: 70
Page 73 and 74: The Optibelt offer is intended for
show all

Standard range - Belting Ware

Create successful ePaper yourself

Delete template?

Save as template?