Standard range - Belting Ware

More documents

Recommendations

Info

Belt designation <strong>Standard</strong> <strong>range</strong> optibelt OMEGA HL sections and dimensions Optibelt OMEGA 14M HL Pitch length Number Pitch length Number Belt designation [mm] of teeth [mm] of teeth On request Section 14M HL t [mm] 14.0 h s [mm] 9.5 h t [mm] 5.6 9
Top surface A durable and flexible top surface protects the tension cord from external influences. In addition, the polychloroprene compound is reinforced with aramid fibres and moderately resistant to mineral oils and humidity and protects from wear due to friction. Tension cord The tension cords are reinforced glass fibre counter twisted and laid in pairs. These tension cords have very high tensile strength, very high flexibility and minimal stretch. Teeth The teeth consist of a new polychloroprene compound reinforced with aramid fibres, which guarantee high shear strength. They are shaped in such a way and exactly spaced so that they mesh perfectly with the pulley teeth with minimal friction. The indent in the tooth tip promotes quiet running. Fabric The specially designed polyamide fabric distinguishes itself by its extraordinarily low friction coefficient and its low noise characteristics. This fabric also protects the teeth from premature wear and cracking 10 Product description optibelt OMEGA HP timing belts Construction The high performance timing belt for high load, high speed machine drives Compact synchronous drives are used in the whole field of mechanical drive engineering. High power transmission capability, good running characteristics and high operational safety are only some of the demands made on timing belts. Modern manufacturing techniques and quality inspections during all processing stages ensure products of the highest reliability. Optibelt OMEGA HP high performance timing belts have been especially developed for high load, low and high speed drives that are evenly loaded without heavy shock. Improved materials and optimised production form the basis for this very high performance spectrum. Optibelt OMEGA, OMEGA HP and OMEGA HL timing belts are used in Optibelt ZRS-HTD ® pulleys or in RPP ® Top surface Tension cord Tooth Fabric pulleys. For the applications using other pulleys, please contact the Optibelt Applications Engineering Department. Example of application: test bench The new high performance timing belt Optibelt OMEGA 5M HP In the field of high performance timing belts the Optibelt OMEGA 5M HP has been newly developed for small pulley diameters, short centre distances and high speeds. The Optibelt OMEGA 5M HP transmits up to 3 times the power of an Optibelt OMEGA 5M (an increase in power of up to 200%). The performance level of the Optibelt OMEGA 5M HP corresponds – with the same pulley diameters – roughly to the level of the considerably larger section Optibelt OMEGA 8M.
Page 1 and 2: NEW OMEGA HL OMEGA 5M HP FOR DRIVES
Page 3 and 4: Produktionsstätten und Vertriebsor
Page 5 and 6: 4 Properties of optibelt OMEGA timi
Page 7 and 8: Construction 6 Top surface Tension
Page 9: 8 Belt designation Order example: S
Page 13 and 14: Order example: Timing belts: Optibe
Page 15 and 16: Order example: 14 Belt designation
Page 17 and 18: Construction 16 Product description
Page 19 and 20: 18 111 3M 111 37 129 3M 129 43 141
Page 21 and 22: Order example: Timing belts: Optibe
Page 23 and 24: 22 Calculation optibelt OMEGA HL/HP
Page 25 and 26: Diagram 2 Speed of the small timing
Page 27 and 28: Total service faktor c 2 26 Calcula
Page 29 and 30: Prime mover Electric motor 50 Hz St
Page 31 and 32: 30 Calculation optibelt OMEGA HL/HP
Page 33 and 34: 32 Speed of the small timing pulley
Page 45 and 46: 44 Number of teeth 10 9.55 8.79 11
Page 47 and 48: 46 Number of teeth Standard timing
Page 49 and 50: 48 optibelt ZRS HTD ® timing pulle
Page 51 and 52: optibelt ZRS HTD ® timing pulleys
Page 59 and 60: Taper bush 58 optibelt ZRS HTD ® t
Page 61 and 62:
Taper bush 60 optibelt ZRS HTD ® t
Page 63 and 64:
Bore diameter d 2 (mm) Tightening t
Page 65 and 66:
Permissible variation in tooth pitc
Page 67 and 68:
Flanged pulleys For the guidance of
Page 69 and 70:
68 Design hints Problems - Causes -
Page 71 and 72:
Details of the drive: 70
Page 73 and 74:
The Optibelt offer is intended for
show all

Standard range - Belting Ware

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?