Hanging Platform - Combisafe
Hanging Platform - Combisafe Hanging Platform - Combisafe
AssemblyCombisafe Hanging PlatformSteel Mesh Barrier 3204Another method of closing the end of the platform and make sure the working areais fully screened is using a Steel Mesh Barrier 3204 combined with SMB AngleConsoles 3228 to interconnect the Steel Mesh Barriers.Mount the two SMB Angle Consoles 3228 to the longitudinal Steel Mesh Barrier3203 first and make sure they are positioned close to the bottom and top of theBarrier, as far apart as possible. Put the shorter Steel Mesh Barrier 3204 into positionperpendicularly and secure it to the two SMB Angle Consoles.Figure 47. Closing end of platform by using Steel Mesh Barrier 3204 and SMBAngle Consoles 322846
Combisafe Hanging PlatformInspectionInspectionInspection after assemblyThe completed installation must be inspected prior to handover.The following checklist should be used:Checklist for installing the Hanging Platform• Has the Hanging Platform been inspected and does it conform to the localregulations?• Is the max c-c distance 2.4 m?• Are the mounting points strong enough?• Does the support to the facade have adequate bearing capacity or inserts?• Is the working surface fixed down?• Are the toe boards fitted?• Is the guard rail strong enough? Do not use wood for slopes over 10º.• Are the gables protected?• Are there access routes?• Are the Hanging Platform Consoles properly anchored?Hanging Platform Clamp• Is the distance to the edge of the holes in the roof truss correct?• Are the through screws and clamps properly tightened?• Is the A dimension correct?Keyhole Attachment• Is the fixing suitable for the base material and correctly installed, edge distanceetc.?• Is the Keyhole Attachment properly fitted?Hanging Platform Beam• Is the fixing suitable for the base material and correctly installed, edge distanceetc.?• Have the cantilever loads been correctly assessed and considered?• Is the Keyhole Attachment properly fitted?Relocator• Is this used together with the Keyhole Attachment?• Is it correctly fitted to the Keyhole Attachment?• Is the Telescope Arm attached with two screws?47
- Page 1: ®COMBISAFEHanging PlatformIncludin
- Page 4 and 5: GeneralCombisafe Hanging PlatformGe
- Page 6: Safety instructionsCombisafe Hangin
- Page 9 and 10: Combisafe Hanging PlatformTechnical
- Page 11 and 12: Combisafe Hanging PlatformTechnical
- Page 13 and 14: Combisafe Hanging PlatformTechnical
- Page 15 and 16: Combisafe Hanging PlatformTechnical
- Page 17 and 18: 2115_0022115_001Combisafe Hanging P
- Page 19 and 20: Combisafe Hanging PlatformTechnical
- Page 21 and 22: Combisafe Hanging PlatformTechnical
- Page 23 and 24: Combisafe Hanging PlatformTechnical
- Page 25 and 26: 918Combisafe Hanging PlatformTechni
- Page 27 and 28: 2130_001Combisafe Hanging PlatformA
- Page 29 and 30: Combisafe Hanging PlatformAssemblyK
- Page 31 and 32: Combisafe Hanging PlatformAssemblyH
- Page 33 and 34: Combisafe Hanging PlatformAssemblyA
- Page 35 and 36: Combisafe Hanging PlatformAssemblyN
- Page 37 and 38: Combisafe Hanging PlatformAssembly2
- Page 39 and 40: Combisafe Hanging PlatformAssembly5
- Page 41 and 42: Combisafe Hanging PlatformAssemblyS
- Page 43 and 44: Combisafe Hanging PlatformAssemblyF
- Page 45: 2350_002Combisafe Hanging PlatformA
- Page 49 and 50: Combisafe Hanging PlatformMaintenan
- Page 52: ®COMBISAFECombisafe International
Assembly<strong>Combisafe</strong> <strong>Hanging</strong> <strong>Platform</strong>Steel Mesh Barrier 3204Another method of closing the end of the platform and make sure the working areais fully screened is using a Steel Mesh Barrier 3204 combined with SMB AngleConsoles 3228 to interconnect the Steel Mesh Barriers.Mount the two SMB Angle Consoles 3228 to the longitudinal Steel Mesh Barrier3203 first and make sure they are positioned close to the bottom and top of theBarrier, as far apart as possible. Put the shorter Steel Mesh Barrier 3204 into positionperpendicularly and secure it to the two SMB Angle Consoles.Figure 47. Closing end of platform by using Steel Mesh Barrier 3204 and SMBAngle Consoles 322846