TTG-7000 operation manual - AvionTEq
TTG-7000 operation manual - AvionTEq TTG-7000 operation manual - AvionTEq
3.1.3.1. Transponder SettingsFigure 3.1.3.1.1 illustrates the TTG-7000 Transponder Settings Menu. The Transponder Settings Menuallows the user to configure the Transmitter, Receiver, and Antenna Simulator modules within the testset for transponder tests. This menu is mainly used for testing and troubleshooting of the TTG-7000.For Transponder unit testing, this menu should only be used to set the individual RF generatorfrequencies.12345678Figure 3.1.3.1.1 – Transponder Settings MenuMenu Control Function1 Suppression Out On/Off. Future use.2 Receiver Path Combobox allows the user to select which port to connect theTop/Bottom Receiver. Selections available are Rx T1/B1, Rx T2/B2, Rx T3/B3, RxT4/B4, Chamber, or Combine.3 Tx Frequency Numeric Box allows the setting of the Transmitter frequency. Individualsetting for each transmitter. Range from 962 to 1213 MHz in 0.1 MHz steps.4 Tx Power Numeric Box allows the setting of the Transmitter power from -20 to -90dBm in 1 dB steps.TTG-7000 User’s Manual Page 13090-7000-0001 Rev E
Menu Control Function5 Tx Path allows setting the Tx path to Top All Ports/Bottom All Ports/Single Port.6 External Modulation On/Off. Future use.7 Modulation CW/Pulse8 Pulse Risetime/Falltime slow or normal.SoftkeyFactory SettingsSignal Generator MenuGenerator AFrequencyModulationPathPowerRise/FallExt. ModGenerator BGenerator CGenerator DGenerator EGenerator FFunctionSets all hardware to default setting according tohardware configuration.Same as menu control item 3.Same as menu control item 7.Same as menu control item 5.Same as menu control item 4.Same as menu control item 8.Same as menu control item 6.Same as Generator A.Same as Generator A.Same as Generator A.Same as Generator A.Same as Generator A.Receiver Path Same as menu control item 2.Suppression Out On/OffFuture use.TTG-7000 User’s Manual Page 13190-7000-0001 Rev E
- Page 79 and 80: Menu Control Function10 Vertical Sp
- Page 81 and 82: 3.1.2.5.5. Static Mode S Extended D
- Page 83 and 84: Menu Control Function40 CA FieldSof
- Page 85 and 86: 3.1.2.5.5.1. Mode S Squitter Defini
- Page 87 and 88: 3.1.2.5.5.3. Velocity Squitter Defi
- Page 89 and 90: 3.1.2.5.5.4. Ident Squitter Definit
- Page 91 and 92: 3.1.2.5.5.5. BDS Register Definitio
- Page 93 and 94: Menu Control Function5 Altitude num
- Page 95 and 96: SoftkeyFunctionTransponder Capabili
- Page 97 and 98: Menu Control Function8 Latitude. Ra
- Page 99 and 100: 3.1.2.5.8. Dynamic TIS-B Definition
- Page 101 and 102: SoftkeyFunctionIdent Format Type Sa
- Page 103 and 104: Menu Control Function8 Latitude. Ra
- Page 105 and 106: 3.1.2.5.10. Dynamic ADS-R Definitio
- Page 107 and 108: SoftkeyFunctionAltitude Same as men
- Page 109 and 110: 3.1.2.5.12. TCAS Ground Station Men
- Page 111 and 112: SoftkeyFunctioncontents.TTG-7000 Us
- Page 113 and 114: SoftkeyResetF1 Pulse C1 Pulse A1 Pu
- Page 115 and 116: SoftkeyFunctionTx Channel Same as m
- Page 117 and 118: Menu Control Function10 Vertical Sp
- Page 119 and 120: SoftkeyFunctionVideo Block Number S
- Page 121 and 122: 3.1.2.6. TCAS ATE Line MenuFigure 3
- Page 123 and 124: 3.1.2.7. TCAS Chamber Mode MenuFigu
- Page 125 and 126: 3.1.2.8. Measurement MenuFigure 3.1
- Page 127 and 128: 123478956Figure 3.1.2.8.2 - Measure
- Page 129: 3.1.3. Transponder MenuFigure 3.1.3
- Page 133 and 134: Menu Control Function8 Suppression
- Page 135 and 136: Menu Control Function8 Suppression
- Page 137 and 138: Menu Control Function8 Suppression
- Page 139 and 140: Menu Control Function8 Suppression
- Page 141 and 142: Menu Control Functionsteps. Power d
- Page 143 and 144: Menu Control Functionsteps. Power d
- Page 145 and 146: Menu Control Function9 Interrogatio
- Page 147 and 148: 3.1.4.1. UAT SettingsFigure 3.1.4.1
- Page 149 and 150: 3.1.4.2. UAT Receiver MenuFigure 3.
- Page 151 and 152: SoftkeyFiltered Masked MenuHighligh
- Page 153 and 154: SoftkeyFunctionAltitude Same as men
- Page 155 and 156: Menu Control Functionsaved file.9 U
- Page 157 and 158: Menu Control Function12 NIC13 Uplin
- Page 159 and 160: Figure 3.1.4.4.1.3 illustrates the
- Page 161 and 162: SoftkeyFunctionType Same as menu co
- Page 163 and 164: SoftkeyFunctionType Same as menu co
- Page 165 and 166: 5. If all devices enabled in the co
- Page 167 and 168: 10. If the scenario terminates, the
- Page 169 and 170: LatitudeLongitude-90 to 90 degrees-
- Page 171 and 172: Stop at Scenario Duration 0 to Scen
- Page 173 and 174: Identification CodeStatic (STAxxx)
- Page 175 and 176: Note: That for all intruders the lo
- Page 177 and 178: Figure 4.2 - VNC Viewer Connection
- Page 179 and 180: 5. TEST CONFIGURATIONSTTG-7000 User
Menu Control Function5 Tx Path allows setting the Tx path to Top All Ports/Bottom All Ports/Single Port.6 External Modulation On/Off. Future use.7 Modulation CW/Pulse8 Pulse Risetime/Falltime slow or normal.SoftkeyFactory SettingsSignal Generator MenuGenerator AFrequencyModulationPathPowerRise/FallExt. ModGenerator BGenerator CGenerator DGenerator EGenerator FFunctionSets all hardware to default setting according tohardware configuration.Same as menu control item 3.Same as menu control item 7.Same as menu control item 5.Same as menu control item 4.Same as menu control item 8.Same as menu control item 6.Same as Generator A.Same as Generator A.Same as Generator A.Same as Generator A.Same as Generator A.Receiver Path Same as menu control item 2.Suppression Out On/OffFuture use.<strong>TTG</strong>-<strong>7000</strong> User’s Manual Page 13190-<strong>7000</strong>-0001 Rev E