mCq pCO - Standard + Heat Pump - McQuay
mCq pCO - Standard + Heat Pump - McQuay mCq pCO - Standard + Heat Pump - McQuay
Conditioning: pCO Standard chiller + heat pump User Guide ver. 2.9 02/11/99Mounting pCO optional cardsClock cardThe clock card is necessary to display the current time and date and to perform a time-zonecontrol action.Connect it to connector no. 3 shown in the figure onpage 7.In the event of power supply failure to pCO, the clockcard will be powered by a rechargable lithium battery(45 mA/h, min. operating time = one month).MNEWCLOCK0CodeOptoisolated RS422 serial cardThe RS422 serial card allows pCO to be networkconnected into local or remote supervisory andtelemaintenance systems.Connect this card to the relative connector (4) shownon page 7.PCOSER0000CodeConnection to a 80-column serial printer: electrical diagram.connettore9 poli - femminapCORXTXGNDData Terminal ReadyClear to SendData Set ReadyCarrier Detect235486123768205connettore25 poli - maschiostampanteMounting the EpromThe Eprom must be inserted into the main card.An arrow on the label of the eprom indicates how to insert it correctly.When inserting the eprom into its socket payattention to align its polarity correctly (the notch onthe eprom must coincide with that of the socket).Insert the eprom carefully without bending orbreaking its small pins.Pag.10/61
Conditioning: pCO Standard chiller + heat pump User Guide ver. 2.9 02/11/99Before requesting ServiceTHE UNIT DOES NOT STARTLed of the Enter key off, Lcd off, other led indicators off.Cause:a. no mains voltageb. transformer (220 - 24V) is not powered with 24 Vacc. 24V power supply connector is not well plugged-inTHE UNIT IS ON BUT:the alarm led indicator is ONthe LCD shows no messages or random messagesthe buzzer soundsCause:a. eprom inserted with wrong polarityb. pins of the eprom bentc. microprocessor chip damaged: contact qualified service personneld: telephone cable from terminal to main card is not correctly connectedWRONG INPUT SIGNALS READINGCause:a. incorrect probe connectionsb. probes' wires must be placed far from electrical noises (power cables, contactors, hightension cables, etc.)c. incorrect connection between interfaces and controller (flat cables)d. incorrect power source to interfacesFAULTY EEPROMa. contact qualified service personnelpCO TURNS OFF AND ON REPEATEDLY (WATCH-DOG) OR IT OPERATES SOME(DIGITAL AND/OR ANALOGUE) OUTPUTS AT RANDOM.Cause:a. incorrect power supplyb. power cables are too close to the microprocessors of the interfaces and to the controlcard.Inputs / OutputsAnalogue inputsPag.11/61
- Page 1 and 2: Conditioning: pCO Standard chiller
- Page 3 and 4: Conditioning: pCO Standard chiller
- Page 5 and 6: Conditioning: pCO Standard chiller
- Page 7 and 8: Conditioning: pCO Standard chiller
- Page 9: Conditioning: pCO Standard chiller
- Page 13 and 14: Conditioning: pCO Standard chiller
- Page 15: Conditioning: pCO Standard chiller
- Page 18 and 19: Conditioning: pCO Standard chiller
- Page 20 and 21: Conditioning: pCO Standard chiller
- Page 22 and 23: Conditioning: pCO Standard chiller
- Page 24 and 25: Conditioning: pCO Standard chiller
- Page 26 and 27: Conditioning: pCO Standard chiller
- Page 28 and 29: Conditioning: pCO Standard chiller
- Page 30 and 31: Conditioning: pCO Standard chiller
- Page 32 and 33: Conditioning: pCO Standard chiller
- Page 34 and 35: Conditioning: pCO Standard chiller
- Page 36 and 37: Conditioning: pCO Standard chiller
- Page 38 and 39: Conditioning: pCO Standard chiller
- Page 40 and 41: Conditioning: pCO Standard chiller
- Page 42 and 43: Conditioning: pCO Standard chiller
- Page 44 and 45: Conditioning: pCO Standard chiller
- Page 46 and 47: Conditioning: pCO Standard chiller
- Page 48 and 49: Conditioning: pCO Standard chiller
- Page 50 and 51: Conditioning: pCO Standard chiller
- Page 52 and 53: Conditioning: pCO Standard chiller
- Page 54 and 55: Conditioning: pCO Standard chiller
- Page 56 and 57: Conditioning: pCO Standard chiller
- Page 58 and 59: Conditioning: pCO Standard chiller
Conditioning: <strong>pCO</strong> <strong>Standard</strong> chiller + heat pump User Guide ver. 2.9 02/11/99Before requesting ServiceTHE UNIT DOES NOT STARTLed of the Enter key off, Lcd off, other led indicators off.Cause:a. no mains voltageb. transformer (220 - 24V) is not powered with 24 Vacc. 24V power supply connector is not well plugged-inTHE UNIT IS ON BUT:the alarm led indicator is ONthe LCD shows no messages or random messagesthe buzzer soundsCause:a. eprom inserted with wrong polarityb. pins of the eprom bentc. microprocessor chip damaged: contact qualified service personneld: telephone cable from terminal to main card is not correctly connectedWRONG INPUT SIGNALS READINGCause:a. incorrect probe connectionsb. probes' wires must be placed far from electrical noises (power cables, contactors, hightension cables, etc.)c. incorrect connection between interfaces and controller (flat cables)d. incorrect power source to interfacesFAULTY EEPROMa. contact qualified service personnel<strong>pCO</strong> TURNS OFF AND ON REPEATEDLY (WATCH-DOG) OR IT OPERATES SOME(DIGITAL AND/OR ANALOGUE) OUTPUTS AT RANDOM.Cause:a. incorrect power supplyb. power cables are too close to the microprocessors of the interfaces and to the controlcard.Inputs / OutputsAnalogue inputsPag.11/61