CS5531/32/33/34 - Eshop-Rychle.cz
CS5531/32/33/34 - Eshop-Rychle.cz CS5531/32/33/34 - Eshop-Rychle.cz
CS5531/32/33/3424 PIN SSOP PACKAGE DRAWINGNDE1 1Ee b 2 A1SIDE VIEWA2ASEATINGPLANE∝LEND VIEW1 2 3TOP VIEWINCHES MILLIMETERS NOTEDIM MIN MAX MIN MAXA -- 0.084 -- 2.13A1 0.002 0.010 0.05 0.25A2 0.064 0.074 1.62 1.88b 0.009 0.015 0.22 0.38 2,3D 0.311 0.335 7.90 8.50 1E 0.291 0.323 7.40 8.20E1 0.197 0.220 5.00 5.60 1e 0.024 0.027 0.61 0.69L 0.025 0.040 0.63 1.03∝ 0° 8° 0° 8°Notes: 1. “D” and “E1” are reference datums and do not included mold flash or protrusions, but do include moldmismatch and are measured at the parting line, mold flash or protrusions shall not exceed 0.20 mm perside.2. Dimension “b” does not include dambar protrusion/intrusion. Allowable dambar protrusion shall be0.13 mm total in excess of “b” dimension at maximum material condition. Dambar intrusion shall notreduce dimension “b” by more than 0.07 mm at least material condition.3. These dimensions apply to the flat section of the lead between 0.10 and 0.25 mm from lead tips.50 DS289PP5
• Notes •
- Page 1 and 2: CS5531/32/33/3416-Bit and 24-Bit AD
- Page 3 and 4: CS5531/32/33/342.3.8. Filter Rate S
- Page 5 and 6: CS5531/32/33/341. CHARACTERISTICS A
- Page 7 and 8: CS5531/32/33/34ANALOG CHARACTERISTI
- Page 9 and 10: TYPICAL RMS NOISE (nV), CS5532/34-B
- Page 11 and 12: CS5531/32/33/34DYNAMIC CHARACTERIST
- Page 13 and 14: CS5531/32/33/34CSSDISCLKt3MSB MSB-1
- Page 15 and 16: CS5531/32/33/34-40°C to +85°C (MC
- Page 17 and 18: CS5531/32/33/34Using the single con
- Page 19 and 20: CS5531/32/33/342.2.2. Command Regis
- Page 21 and 22: CS5531/32/33/34READ/WRITE INDIVIDUA
- Page 23 and 24: CS5531/32/33/34PERFORM CALIBRATIOND
- Page 25 and 26: CS5531/32/33/342.2.5. Reading/Writi
- Page 27 and 28: CS5531/32/33/34φ1 Fineφ1 FineVREF
- Page 29 and 30: CS5531/32/33/34Filter Rate Select,
- Page 31 and 32: CS5531/32/33/34U/B (Unipolar / Bipo
- Page 33 and 34: CS5531/32/33/342.5.4. Performing Ca
- Page 35 and 36: CS5531/32/33/34sult in the loss of
- Page 37 and 38: CS5531/32/33/34FRS (WR3-WR0)Clock C
- Page 39 and 40: CS5531/32/33/34Unipolar InputVoltag
- Page 41 and 42: CS5531/32/33/342.10. Clock Generato
- Page 43 and 44: CS5531/32/33/34+2.5 V+3 V ~ +5 VAna
- Page 45 and 46: CS5531/32/33/342.12. Getting Starte
- Page 47 and 48: CS5531/32/33/34SDI - Serial Data In
- Page 49: CS5531/32/33/346. PACKAGE DRAWINGSN
<strong>CS5531</strong>/<strong>32</strong>/<strong>33</strong>/<strong>34</strong>24 PIN SSOP PACKAGE DRAWINGNDE1 1Ee b 2 A1SIDE VIEWA2ASEATINGPLANE∝LEND VIEW1 2 3TOP VIEWINCHES MILLIMETERS NOTEDIM MIN MAX MIN MAXA -- 0.084 -- 2.13A1 0.002 0.010 0.05 0.25A2 0.064 0.074 1.62 1.88b 0.009 0.015 0.22 0.38 2,3D 0.311 0.<strong>33</strong>5 7.90 8.50 1E 0.291 0.<strong>32</strong>3 7.40 8.20E1 0.197 0.220 5.00 5.60 1e 0.024 0.027 0.61 0.69L 0.025 0.040 0.63 1.03∝ 0° 8° 0° 8°Notes: 1. “D” and “E1” are reference datums and do not included mold flash or protrusions, but do include moldmismatch and are measured at the parting line, mold flash or protrusions shall not exceed 0.20 mm perside.2. Dimension “b” does not include dambar protrusion/intrusion. Allowable dambar protrusion shall be0.13 mm total in excess of “b” dimension at maximum material condition. Dambar intrusion shall notreduce dimension “b” by more than 0.07 mm at least material condition.3. These dimensions apply to the flat section of the lead between 0.10 and 0.25 mm from lead tips.50 DS289PP5