Measuring Gas Velocity with the D-FL 100 Differential Pressure Bar

More documents

Recommendations

Info

D−FL 100 Seite 247. MaintenanceThe D-FL 100 is a low-maintenance system with long maintenance intervals. The maintenance scheduledepends on the application, and is generally several months (3 months as a rule of thumb). Pressureconditions, climatic and other ambient influences at the measuring site, and the gas being measured allaffect the maintenance schedule.Maintenance work should be performed in the following order:1. Adjust menu item Maintenance at the D-FL 100-10 Display.Use the MOD key on the D-FL 100-10 Display to select Stand by.2. Clean the exterior of the unit.3. Check the differential pressure bar and the differential pressure transducer.Check exterior covers and the connections between differential pre ssure bar and transducer.4. Flush the measuring pipes.The pipes may need to be flushed, depending on application conditions. By changing the setting ofthe switching valve, purge air is directed separately to the different pressure lines (see Fig. 4 forswitching valve settings).5. Clean the differential pressure bar.Under extreme application conditions, when a simple flushing of the pressure lines would not besufficient, the differential pressure bar must be cleaned with a cloth or a brush. The differentialpressure bar must first be disconnected from the transducer and removed from the duct/stack. Themaintenance intervals need to be shorter under such extreme application conditions.6. Make a zero point adjustment of the differential pressure transducer.The two wires on the transducer are cross-wired via the switching valve, and the exhaust screwsare opened briefly and shut again (pressure equalization at transducer).Remove the housing cover from the transducer to monitor the electric current signal on the display.The current output must now be 4.00 mA. If it is not, a zero point adjustment must be made.Remove both screws from the protective cover and remove the cover. Use the M key to proceed topoint 7 and perform the adjustment. Press and simultaneously for about 2 seconds. Thedisplay should now show 4.00 mA; if it does not, repeat the adjustment.7. Switch on the D-FL 100-10 Display.Use the MOD key on the D-FL 100-10 Display to proceed with the measuring process.GmbH
D−FL 100 Seite 258. Specifications of the D-FL 100Measuring principle: Continuous in situ measurement by the differential pressure method.Lengths of the measuring paths:Differential pressure bar I: ...................................... 400 - 2000 mm (15 ¾ in. – 78 ¾ in.)Differential pressure bar II: ..................................... 2000 - 4000mm (78 ¾ in. – 157 ½ in.)Differential pressure bar lll: ..................................... 4000-8000mm (157 ½ in.) – 315 in.)Measuring range: ................................................... 0 - 2.000.000 Nm³/h,Minimum velocity: ................................................... 3 m/sExhaust temperature (standard material):............... min. greater than the dew point................................................................................. max. 400°CDifferential pressure bar material: .......................... 1.4571 (standard),2.4819, 2.4816 according to customer requestMargin of error: ....................................................... +/-2%Electrical specifications of the D-FL 100-10 DisplayVoltage: .................................................................. 115/230 V (±10%)Frequency: .............................................................. 50/60 Hz(Other voltages and frequencies are available upon request.)Limiting valueTwo independently adjustable limiting values: L.V. 1, L.V. 21 x Status "Measure"All relay contacts potential-free,maximal load at cosϕ = 1: ...................................... 230V / 0.5AMaximum admissible ambient temperature range: -20° +50°CIntegration period of the measured value: .............. 1 - 180 sec (freely selectable)Output signal: ......................................................... analog 4 - 20 mAMaximum load: ....................................................... 500 OhmLive zero: ................................................................ 4 mAProtection/weight:rack mount model (IP20): ................................... 2,0 kghousing model (IP65): ....................................... 2,2 kgGmbH
Page 2 and 3: Document:man_dfl100_uk.docVersion:
Page 4 and 5: D-FL 100IllustrationsFig. 1: Diagra
Page 6 and 7: D−FL 100 Seite 2Fig. 1:Diagram of
Page 8 and 9: D−FL 100 Seite 4placed on the dif
Page 10 and 11: D−FL 100 Seite 63. System Compone
Page 12 and 13: D−FL 100 Seite 83.2. Differential
Page 14 and 15: D−FL 100 Seite 10LED DisplayStand
Page 16 and 17: D−FL 100 Seite 12After the differ
Page 18 and 19: D−FL 100 Seite 144.3. Electrical
Page 20 and 21: D−FL 100 Seite 16Fig. 15:Connecti
Page 22 and 23: D−FL 100 Seite 18Fig. 17:Connecti
Page 24 and 25: D−FL 100 Seite 205. Start-Up / Er
Page 26 and 27: D−FL 100 Seite 22LED readout inst
Page 30 and 31: D−FL 100 Seite 26Differential Pre
Page 32 and 33: D−FL 100 Seite 28Installation fla
Page 34 and 35: D−FL 100 Seite 30Inner diameter(m
Page 36 and 37: D−FL 100 Seite 329.5. Ordering In
Page 38 and 39: D−FL 100 Seite 34** Other materia
Page 40 and 41: D−FL 100 Seite 369.6.2. Variant e
Page 42 and 43: D−FL 100 Seite 3810. Calculation
Page 44 and 45: D−FL 100 Seite 4010.1. Explanatio
Page 46 and 47: D−FL 100 Seite 420C ° = b · 4mA
Page 48 and 49: D−FL 100 Seite 44GmbH
Page 50 and 51: D−FL 100 Seite 46II.Eignung von M
Page 52 and 53: D−FL 100 Seite 48DURAG GROUP comp

Measuring Gas Velocity with the D-FL 100 Differential Pressure Bar

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?