TH-D72A/E - N3UJJ
TH-D72A/E - N3UJJ TH-D72A/E - N3UJJ
8 MCP-4A MEMORY CONTROL PROGRAM (FOR USE WITH TH-D72A/E)4. Click “Start” > “Program” > “KENWOOD” > “MCP-4A” to start MCP-4A.Figure 8-2 MCP-4A Splash Window5. Select the communication port.Specify in the COM Port frame the communication port (COM Port) that will be used tocommunicate via your computer with the target station. You cannot select grayed out ports. If allports are grayed out, this indicates your computer has no COM ports installed and you will not beable to use the MCP-4A software even if you click the “OK” button.Figure 8-3 MCP-4A COM Port Setting Window6. Read the information of TH-D72A/E.Read the desired information of TH-D72A/E that you wish to edit.Click the “OK” button. Next, select “Read Data from the Transceiver” from the Program pulldownmenu and read the information from the target transceiver.Note: The basic method of using MCP-4A is to read the existing transceiver data into MCP-4A, edit the configuration, andthen write the new configuration back to the transceiver.66 CONTENTS TH-D72A/EFrom The N3UJJ.COM Document Library
8 MCP-4A MEMORY CONTROL PROGRAM (FOR USE WITH TH-D72A/E)Figure 8-4 MCP-4A Read Transceiver Advisory MessageFigure 8-5 MCP-4A Program Menu: Read Data from the TransceiverTH-D72A/E CONTENTS 67From The N3UJJ.COM Document Library
- Page 23 and 24: 3 PREPARATIONS FOR OPERATING APRS3.
- Page 25 and 26: 3 PREPARATIONS FOR OPERATING APRS3.
- Page 27 and 28: 3 PREPARATIONS FOR OPERATING APRS3.
- Page 29 and 30: 3 PREPARATIONS FOR OPERATING APRS3.
- Page 31 and 32: 3 PREPARATIONS FOR OPERATING APRS3.
- Page 33 and 34: 4 GPS4.1.2 Datum (Geodetic Survey S
- Page 35 and 36: 4 GPS4.2.4 Settings for Geodetic Su
- Page 37 and 38: “Time, Altitude, Travel direction
- Page 39 and 40: 4 GPS4.3.5 Internal GPS Unit SaveIf
- Page 41 and 42: 4 GPSPressing the [TNC] key again i
- Page 43 and 44: 4 GPS4.3.9 Mark WaypointYou can reg
- Page 45 and 46: 5 APRS SOFTWARE FOR YOUR PC5.1 UI-V
- Page 47 and 48: 5 APRS SOFTWARE FOR YOUR PCFigure 5
- Page 49 and 50: 6 OPERATIONAL EXAMPLES OF APRSWhile
- Page 51 and 52: 6 OPERATIONAL EXAMPLES OF APRS6.1.4
- Page 53 and 54: 6 OPERATIONAL EXAMPLES OF APRSBy ch
- Page 55 and 56: 6 OPERATIONAL EXAMPLES OF APRS6.1.6
- Page 57 and 58: 6 OPERATIONAL EXAMPLES OF APRS6.1.6
- Page 59 and 60: 6.2 Base Station (Weather Station)6
- Page 61 and 62: 7 APRS NETWORKS7.1 APRS ServersIn t
- Page 63 and 64: 7 APRS NETWORKS7.3 Let’s Send Ema
- Page 65 and 66: 7 APRS NETWORKS7.4 Digipeaters (Dig
- Page 67 and 68: 7 APRS NETWORKSAlthough UITRACE usi
- Page 69 and 70: 7 APRS NETWORKSthe same time also h
- Page 71 and 72: 7 APRS NETWORKS7.5.3 STATE/ SECTION
- Page 73: 8 MCP-4A MEMORY CONTROL PROGRAM (FO
- Page 77 and 78: 8.3 Reading a FileThis section desc
- Page 79 and 80: 8 MCP-4A MEMORY CONTROL PROGRAM (FO
- Page 81 and 82: 8 MCP-4A MEMORY CONTROL PROGRAM (FO
- Page 83 and 84: 8 MCP-4A MEMORY CONTROL PROGRAM (FO
- Page 85 and 86: 9 HOW TO UPDATE FIRMWARE9.3 How to
- Page 87 and 88: 10 MISCELLANEOUS TOPICS10.1 AvMap (
- Page 89 and 90: 11 APPENDIXRevision HistoryRevision
- Page 91 and 92: We would like to extend our sincere
8 MCP-4A MEMORY CONTROL PROGRAM (FOR USE WI<strong>TH</strong> <strong>TH</strong>-<strong>D72A</strong>/E)4. Click “Start” > “Program” > “KENWOOD” > “MCP-4A” to start MCP-4A.Figure 8-2 MCP-4A Splash Window5. Select the communication port.Specify in the COM Port frame the communication port (COM Port) that will be used tocommunicate via your computer with the target station. You cannot select grayed out ports. If allports are grayed out, this indicates your computer has no COM ports installed and you will not beable to use the MCP-4A software even if you click the “OK” button.Figure 8-3 MCP-4A COM Port Setting Window6. Read the information of <strong>TH</strong>-<strong>D72A</strong>/E.Read the desired information of <strong>TH</strong>-<strong>D72A</strong>/E that you wish to edit.Click the “OK” button. Next, select “Read Data from the Transceiver” from the Program pulldownmenu and read the information from the target transceiver.Note: The basic method of using MCP-4A is to read the existing transceiver data into MCP-4A, edit the configuration, andthen write the new configuration back to the transceiver.66 CONTENTS <strong>TH</strong>-<strong>D72A</strong>/EFrom The <strong>N3UJJ</strong>.COM Document Library