Operation Manual - Home Mega Global Solution

More documents

Recommendations

Info

PLUG “F” 10 WAYPIN DESCRIPTION CABLENOTESNoSIZE*79 Generator L1 input 0.5mm Feed via 2A typical rated fuse80 Generator L2 input 0.5mm Feed via 2A fuse. Not used if single phase81 Generator L3 input 0.5mm Feed via 2A fuse. Not used if single phase82 Generator N input 0.5mm83 DO NOT USE Ensure no connection is made to this pin84 DO NOT USE Ensure no connection is made to this pin85 Mains L1 input 0.5mm Feed via 2A fuse86 Mains L2 input 0.5mm Feed via 2A fuse. Not used if singe phase87 Mains L3 input 0.5mm Feed via 2A fuse. Not used if single phase88 Mains N input 0.5mmNOTE:- Cable size* = Is recommended cable size only. Exact cable size will depend oncircuit application and length of cable run. Information above is supplied as a guide only.RS232 -1 (FEMALE)Not normally used - Refer to DSE for details.RS232 -2 (MALE)Telemetry lead connection for direct connection to telemetry PC software or for connection to modemfor remote telemetry. Standard Null Modem Cable.24606 OPERATING MANUAL ISSUE 2 11/27/00 MR
5.2 CONNECTOR FUNCTION DETAILSThe following describes the functions of the 6 connectors on the rear of the module. See rear panellayout FIG 5.PLUG “A” 18 WAYPIN DESCRIPTIONNo1 Oil pressure sender +ve connection. If a digital oil pressure switch is being usedinstead, connect to this pin and ground the other side of the switch.2 Oil pressure sender -ve connection. Only use if using analogue sender3 Oil pressure sender -ve feed. Connect to pin 2 if using insulated return typesenders.4 Fuel level sender +ve. If a digital fuel level switch is being used instead, connectto this pin and ground the other side of the switch.5 Fuel level sender -ve connection. Only use if using analogue sender6 Fuel level sender -ve feed. Connect to pin 2 if using insulated return type senders.7 Engine coolant temp sender +ve connection. If a digital temperature switch isbeing used instead, connect to this pin and ground the other side of the switch.8 Engine coolant temp sender -ve connection. Only use if using analogue sender9 Engine coolant temp sender -ve feed. Connect to pin 2 if using insulated returntype senders.10 Engine oil temp sender +ve connection. If a digital temperature switch is beingused instead, connect to this pin and ground the other side of the switch.11 Engine oil temp sender -ve connection. Only use if using analogue sender12 Engine oil temp sender -ve feed. Connect to pin 2 if using insulated return typesenders.13 DO NOT USE14 Generator L1 current transformer connection.15 Generator L2 current transformer connection. If single phase is used do notconnect this pin.16 Generator L3 current transformer connection. If single phase is used do notconnect this pin.17 Generator current transformer common connection, only to be used if a neutral CTis fitted.18 Generator current transformer Neutral connection. If no neutral CT is fitted use thispin as CT Common.PLUG “B” 15 WAYPIN DESCRIPTIONNo19 Output 8 Normally closed change-over contact. Normally a spare auxiliary output.However if breaker control scheme is being used this is used for the Mains ACBclose connection.20 Output 8 Common change-over contact.21 Output 8 Normally open change-over contact22 DO NOT USE23 Output 7 Normally closed change-over contact. Normally a spare auxiliary output.However if breaker control scheme is being used this is used for the Mains ACBshunt trip or UV coil connection.24 Output 7 Common change-over contact.25 Output 7 Normally open change-over contact.26 DO NOT USE27 Output 6 Normally closed change-over contact.28 Output 6 Common change-over contact.606 OPERATING MANUAL ISSUE 2 11/27/00 MR25
Page 1 and 2: Deep Sea Electronics PlcMODEL 606OP
Page 3 and 4: 9. TYPICAL WIRING DIAGRAM..........
Page 5 and 6: 1. OPERATION1.1 CONTROLControl of t
Page 7 and 8: attempts to start have been complet
Page 9 and 10: BATTERY HIGH VOLTAGE, if the module
Page 11 and 12: AUXILIARY INPUTS, if an auxiliary i
Page 13 and 14: NOTE:- If the following screen is d
Page 15 and 16: This LED indicates that the module
Page 17 and 18: i.e.:-Display shows:-EMERGENCY STOP
Page 19 and 20: 4.4 FRONT PANEL LAYOUT4.5 REAR PANE
Page 21 and 22: 29 Output 6 Normally open 0.5mm “
Page 23: PLUG “E” 20 WAYPIN DESCRIPTION
Page 27 and 28: PLUG “E” 20 WAYPIN DESCRIPTIONN
Page 29 and 30: 6. SPECIFICATIONDC Supply8.0 to 35
Page 31 and 32: 8. FAULT FINDINGSYMPTOMPOSSIBLE REM
Page 33: 10. APPENDIX606 OPERATING MANUAL IS

Operation Manual - Home Mega Global Solution

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?