<strong>RFID</strong> <strong>Systems</strong>IDENT Control System InterfacesIDENT ControlSystem Interfaces• 10/100 Mbit Ethernet forEtherNet/IP, PROFINET,Modbus/TCP, TCP/IP, or PCCC• Industrial interface options forDeviceNet, PROFIBUS and RS-232• Graphical display and LEDdiagnostic indicators• Cast aluminum housing100% shieldedThe IDENT Control Interface is the backbone of the entire<strong>RFID</strong> system. It connects directly to your PC/PLC ofchoice and manages all communications to and from the4 read heads. Read heads are configured on power up,and parameters, like multiplex mode and tag type, are setautomatically.Mixed Mode vs. Separated ModeA feature that could make you choose one interface overanother is the mode of operation. You can read and writeto all heads simultaneously. The key difference is thememory mapping in the PLC. In the Mixed Mode operation,all heads respond to the same location in PLC memory.In Separated Mode, memory is set aside for each head.Mixed Mode is great for reducing bus system overheadand Separated Mode is used for speed and programmingease.EtherNet/IPThe Ethernet interface supports EtherNet/IP right out of thebox. With implicit messaging, the data is directly mappedjust like any other I/O card. No expensive configurationsoftware is required for setup. Everything is programmedusing the RSLogix 5000 programming software.Common SpecificationsLCD DISPLAY2 lines, 12 charactersOPERATING VOLTAGE10-30 VDCVOLTAGE RIPPLE≤ 10% at 30 VDCREVERSE POLARITY PROTECTION Yes, with red LED indicationHUMIDITY96% noncondensing,salt spray resistantTEMPERATURE Working -13ºF to +158ºF (-25ºC to +70ºC)RANGE Storage -22ºF to +176ºF (-30ºC to +80ºC)HOUSING MATERIALAluminum, powder coatedWEIGHT35.3 oz.APPROVALSREAD HEAD CONNECTIONPOWER CONNECTION4-pin female M12quick disconnect4-pin male M12quick disconnectTCP/IPStandard socket connections to port 10000 will allow youto send and receive data to IDENT Control. An integratedWeb server makes configuration, setup and testing easyand with the integrated SMTP server emails are sent onerror or data.DeviceNetBecause the DeviceNet current consumption is only 40 mAyou can run 500 ft of DeviceNet cable with more then 84read heads attached to it. DeviceNet also has automaticnode replacement. With this feature, all parametersare downloaded to the interface on power up. Theseparameters may include the assembly instances, tag typeof each head and multiplex mode.SLC 5/05 and PLC 5Read/Write OperationThe SLC5/05 Ethernet processor and the PLC5/xxEEthernet processors do not use standard EtherNet/IPprotocol, but use a protocol called PCCC. This protocol isfully supported and two rungs of ladder will get you up andrunning quickly.Modbus/TCPMany PLCs, such as Modicon and GE, will support theModbus/TCP protocol. This protocol supports multiplesimultaneous users, one PLC can control four heads orfour PLCs can each control one head. This reduces theoverall cost of the installation. The interface is protectedagainst dual head write access.PROFIBUSMany PLCs use PROFIBUS as their high-speed busconnection. Two models are available that allow quick fieldor enclosure mounting. Parameterization is automatic,and the diagnostic interrupt allows signaling of the mastersystem when an error occurs.28Pepperl+Fuchs®<strong>Inc</strong>. • 1600 Enterprise Parkway • Twinsburg, Ohio 44087-2245 • www.am.pepperl-fuchs.comTelephone (330) 486-0001 • FAX (330) 405-4710 • E-Mail: sales@us.pepperl-fuchs.com
<strong>RFID</strong> <strong>Systems</strong>RS-232MODEL IC-KP-B12-V45 IC-KP-B7-V95 IC-KP-B6-SUBD IC-KP-B6-V15B IC-KP-R2-V1PROTOCOLSEtherNet/IP, PROFINET,TCP/IP, Modbus/TCP, DeviceNet PROFIBUS DP RS-232, P+F asciiPCCCBAUD RATES 10/100 Mbps 125, 250, 500 kbps Up to 12 Mbps 38.4 kbpsADDRESS Fixed IP address, DHCP 0-63 0-126 –READ HEAD MAPPING Separated/mixed mode Separated/mixed mode Mixed mode –MIN./MAX. DATA MAPPING SIZES8 bytes/248 bytes 8 bytes/248 bytes 8 bytes/64 bytes –MAX. READ/WRITE DATA 60 bytes (Modbus/TCP, TCP/IP),IN SINGLE SCAN56 bytes (EtherNet/IP)56 bytes 60 bytes 1020 bytesMESSAGING Explicit, implicit, fc3, fc16, fc23 Polled, COS, explicit DPV0 –POWER CONSUMPTION(WITHOUT READ HEADS)3.5 W 2.5 W 3.5 W 2.5 WBUS CURRENTCONSUMPTION– 40 mA – –PROTECTION (IEC) IP67 IP67 IP40 IP67 IP67BUS CONNECTIONWiring DiagramsRJ45+ amphenol7/8" mini9-pinD-subsocket at housing trigger switch trigger sensor (PNP) read/write head21++1112signalA23--1 3334B444554 4Power supply1 321 = + 24 V2 = NC3 = GND4 = NCMale M12 B-codedquick disconnectFemale M12quick disconnectIDENT Control System InterfacesBus ConnectionGround lugIC-KP-B12-V45IC-KP-B7-V95IC-KP-B6-SUBD45 1 drain ShieldTD+TD-RD+not usednot usedRDnotused2not used132 V+ External power supplyVcc (red) 11 V - 25 V3 V- GND (black)4 CAN_H CAN bus signal (white)5 CAN_L CAN bus signal (blue)5 4 3 2 19 8 7 63 = RxD/TxD-P5 = DGND6 = VP8 = RxD/TxD-Nothers = NCIC-KP-B6-V15BIC-KP-R2-V1324151 = VP2 = RxD/TxD-N3 = DGND4 = RxD/TxD-P5 = NC14 231 = NC2 = RxD3 = GND4 = TxDPepperl+Fuchs®<strong>Inc</strong>. • 1600 Enterprise Parkway • Twinsburg, Ohio 44087-2245 • www.am.pepperl-fuchs.comTelephone (330) 486-0001 • FAX (330) 405-4710 • E-Mail: sales@us.pepperl-fuchs.com29