ER-430M SVC M.pdf
ER-430M SVC M.pdf ER-430M SVC M.pdf
3 Installation and Operation3-3-7 Self Test3-3-7-1 Test Printer1. Turn the Mode switch to Service Mode position.1. Press ‘1’, ‘0’ and ‘SBTL’ key on key board.2. Then the printer prints the test pattern. The printing message shows some information sush as ‘TMvalue’,’stbIdx (Strobe index)’.3. After printing, The drawer is opened. Then the printer test is finished.3-3-7-2 Test Display1. Press ‘1’, ‘1’ and ‘SBTL’ key on key board.2. Then the buzzer will work for 1 sec.3. After testing the buzzer, Some characters are displayed on the rear VFD display3-3-7-3 Test Key Board1. Press Press ‘1’, ‘2’ and ‘SBTL’ key on key board.2. Press any key you want on the key board.3. The key code of pressed key will be showed on the VFD.4. Turn the mode switch to any position to finish this test.3-3-7-4 Test Mode Switch1. Press Press ‘1’, ‘3’ and ‘SBTL’ key on key board.2. Turn the mode switch to any position.3. The corresponding Mode name will be showed on the VFD.3-3-7-5 Test RS232C (Serial 1)1. Install the serial loop back test jig. (Short “pin 2,3” and “pin 4,6” of DSUB connector)2. Press Press ‘1’, ‘4’ and ‘SBTL’ key on key board.3. If error occurs, the message (232 NOGOOD) is displayed on VFD and the Buzzer beep.Then Press “Clear” key.3-3-7-6 Test RS232C (Serial 2)1. Install the serial loop back test jig. (Short “pin 2,3” and “pin 4,6” of DSUB connector)2. Press Press ‘2’, ‘4’ and ‘SBTL’ key on key board.3. If error occurs, the message (232 NOGOOD) is displayed on VFD and the Buzzer beep.Then Press “Clear” key.Note : When the ports is unconnected with the cable , the Error occur.3-8 SAM4S ER-430 SERIES
4 Disassembly and AssemblyCaution :· Before installation, be sure to turn off the power switch.· Use gloves to protect your hand from being cut by the angle and the chassis.· Connect all the cables correctly. When connecting or disconnecting the cables, be careful not to applystress to the cables. (It may cause disconnection)· Be careful not to bind interface cables and AC power cord together.Note : Before disassembling, first of all separate the ASS'Y CASE UPPER(B) from the ASS'Y CASE LOWER(E).(Page 6-1)4-1 Disassembling the Case Upper Block4-1-1 Ass’y Case Upper1. Open the ASS'Y COVER PRINTER(A) and lift it off. (Page6-1,Page6-2)2. Remove the three screws(B-16:1pcs, B-18:1pcs,B-27:1PCS) from theASS'Y CASE LOWER(E).(Page6-1, 6-3)3. Separate the four harnesses(c,d, mn) , and two FPC ( uv , ) from the PBA-MAIN BOARD(E-2).(Page6-9)4. Lift off the ASS'Y CASE UPPER(B) from the ASS'Y CASE LOWER(E). (Page6-1, 6-3)4-1-2 Ass’y Front Display(LCD)1. Separate the PMO-WINDOW LCD(B-11) from the PMO-WINDOW DISPLAY(B-12).(Page6-3)2. Separate the PMO-WINDOW DISPLAY(B-12) from the ASS’Y CASE UPPER(B).(Page6-3)3. Remove the four screws(B-24) from the ASS’Y CASE UPPER(B).(Page6-3)4. Remove the four screws(B-21) from the PMO-HOLDER DISPLAY(B-23).(Page6-3)5. Separate the LCD(B-22) from the PMO-HOLDER DISPLAY(B-23).(Page6-3)4-1-3 Ass’y Rear (Turret) Display1. First of all, separate the harness(c) of the REAR DISPLAY BOARD(B-14) from thePBA-MAIN BOARD(E-2). (Page6-9)2. Separate the PMO-TURRET BODY (B-15) from the ASS'Y CASE UPPER (B). (Page6-3)3. Separate the PMO-WINDOW TURRET(B-13) and the REAR DISPLAY BOARD(B-14) from thePMO-TURRET BODY (B-15).(Page6-3)4-1-4 Ass’y Cover Mode Switch1. Separate the ASS'Y COVER MODE S/W(B-10) from the ASS'Y CASE UPPER(B). (Page6-3)2. Remove the two screws(B-5) on the ASS'Y COVER MODE S/W(B-10) and separate theMODE KEY ASS’Y(B-4) from the PMO-COVER MODE S/W(B-10). (Page6-3)3. Remove the two screws(B-2) on the MODE KEY ASS’Y(B-4) and separate theIPR-BRKT MODE S/W(B-3) and the MODE KEY ASS’Y(B-4). (Page6-3)4-1-5 Ass’y Cover MCR(OPTION)1. Separate the ASS'Y COVER MCR(B-1) from the ASS'Y CASE UPPER(B). (Page6-3)2. Remove the two screws(B-5) on the ASS'Y COVER MCR(B-1) and separate theMODE KEY ASS’Y(B-4) from the PMO-COVER MCR(B-1). (Page6-3)3. Remove the two screws(B-2) on the MODE KEY ASS’Y(B-4) and separate theIPR-BRKT MODE S/W(B-3) and the MODE KEY ASS’Y(B-4). (Page6-3)4. Remove the three screws(B-9) from the ASS'Y COVER MCR(B-1) and separate theCOVER-SLOT(B-8) from the ASS'Y CASE UPPER(B). (Page6-3)5. Remove two screws(B-6) from the COVER-SLOT(B-8) and separate theMCR(B-7) from the COVER-SLOT(B-8). (Page6-3)SAM4S ER-430 SERIES 4-1
- Page 1 and 2: ELECTRONIC CASH REGISTERER-430 SERI
- Page 3 and 4: Copyrightc 2006 by Shin Heung Preci
- Page 5 and 6: 1 Precaution StatementsFollow these
- Page 7 and 8: 2 Product SpecificationsSpecificati
- Page 9 and 10: 2 Product Specifications2-3 Thermal
- Page 11 and 12: 2 Product SpecificationsFigure2-3 P
- Page 13 and 14: 2 Product Specifications2-5 Interfa
- Page 15 and 16: 3 Installation and Operation3-1 Sys
- Page 17 and 18: 3-2-2 RS-232C Serial Cable Installa
- Page 19 and 20: 3 Installation and Operation3-3-2 K
- Page 21: 3 Installation and Operation3-3-5 B
- Page 25 and 26: 5 Maintenance and Adjustment5-1 Cle
- Page 28 and 29: 6 Exploded Views and Parts List6-2
- Page 30 and 31: 6 Exploded Views and Parts ListNo.
- Page 32 and 33: 6 Exploded Views and Parts ListFigu
- Page 34 and 35: 6 Exploded Views and Parts List6-2-
- Page 36 and 37: 6 Exploded Views and Parts ListNo.
- Page 38 and 39: 6 Exploded Views and Parts List6-2-
- Page 40 and 41: 6 Exploded Views and Parts ListMEMO
- Page 42 and 43: 7 PCB Layout and Parts ListNo Part-
- Page 44 and 45: 7 PCB Layout and Parts ListNo Part-
- Page 46 and 47: 7 PCB Layout and Parts List7-4 Disp
- Page 48 and 49: 7 PCB Layout and Parts List7-5 Fisc
- Page 50 and 51: 7 PCB Layout and Parts ListMEMO7-10
- Page 52 and 53: 8 Troubleshooting8-2 System Problem
- Page 54 and 55: 8 Troubleshooting8-4 Thermal Printe
- Page 56 and 57: 8 Troubleshooting8-6 Drawer and Spo
- Page 58 and 59: 8 TroubleshootingMEMO8-8 SAM4S ER-4
- Page 60 and 61: 9 Block Diagram9-2 ER-430 / ER-430F
- Page 62 and 63: 9 Block DiagramMEMO9-4 SAM4S ER-430
- Page 64 and 65: 10 Wiring DiagramCN7 = Main to Prin
- Page 66 and 67: 12341234578865897542111-1-1 CPU PAR
- Page 68 and 69: 12345678912323123456978459234567896
- Page 70 and 71: 24837913411-4 INTERFACE PARTA B CD1
3 Installation and Operation3-3-7 Self Test3-3-7-1 Test Printer1. Turn the Mode switch to Service Mode position.1. Press ‘1’, ‘0’ and ‘SBTL’ key on key board.2. Then the printer prints the test pattern. The printing message shows some information sush as ‘TMvalue’,’stbIdx (Strobe index)’.3. After printing, The drawer is opened. Then the printer test is finished.3-3-7-2 Test Display1. Press ‘1’, ‘1’ and ‘SBTL’ key on key board.2. Then the buzzer will work for 1 sec.3. After testing the buzzer, Some characters are displayed on the rear VFD display3-3-7-3 Test Key Board1. Press Press ‘1’, ‘2’ and ‘SBTL’ key on key board.2. Press any key you want on the key board.3. The key code of pressed key will be showed on the VFD.4. Turn the mode switch to any position to finish this test.3-3-7-4 Test Mode Switch1. Press Press ‘1’, ‘3’ and ‘SBTL’ key on key board.2. Turn the mode switch to any position.3. The corresponding Mode name will be showed on the VFD.3-3-7-5 Test RS232C (Serial 1)1. Install the serial loop back test jig. (Short “pin 2,3” and “pin 4,6” of DSUB connector)2. Press Press ‘1’, ‘4’ and ‘SBTL’ key on key board.3. If error occurs, the message (232 NOGOOD) is displayed on VFD and the Buzzer beep.Then Press “Clear” key.3-3-7-6 Test RS232C (Serial 2)1. Install the serial loop back test jig. (Short “pin 2,3” and “pin 4,6” of DSUB connector)2. Press Press ‘2’, ‘4’ and ‘SBTL’ key on key board.3. If error occurs, the message (232 NOGOOD) is displayed on VFD and the Buzzer beep.Then Press “Clear” key.Note : When the ports is unconnected with the cable , the Error occur.3-8 SAM4S <strong>ER</strong>-430 S<strong>ER</strong>IES
Change language