WinTrac⢠5.X
WinTrac⢠5.X WinTrac⢠5.X
Chapter 9Advanced WinTrac FeaturesAccessing the Tools Menu in WinTrac 5The Tools menu is new to WinTrac 5. It allows you to perform tasks such as calibrating sensors, Flash loadingTK device with a new version of software, setting up modes on TK devices, etc. Note that only certain devicessuch as DAS data logger will support these features.Launch WinTrac software.Press 'Ctrl' + 'Shift' + 'T' keys simultaneously.You will see the 'Tools' menu appear in the menu bar.Tools MenuNOTE: If the ‘Tools Menu’ does not appear, the user access level may be set to Read Only Access (level 1). Ifthis is the case, the user access level must be changed to Standard User (level 7). Changing the User Accesslevel is described in the next section. You can hide the 'Tools' menu again by pressing 'Ctrl' + 'Shift' + 'T' keyssimultaneously.76
Chapter 9Advanced WinTrac FeaturesUser-Access level in WinTrac 5 softwareWinTrac 5 allows you to set up different User Access levels for WinTrac software. These levels give the useraccess to different features and functions, depending on the level. There are currently 2 different levels ofUser Access Defined:-Default User AccessUser has full access to the TK Devices. User also gains access to a special Tools menu allowing access tofeatures such as Sensor Calibration, Flash load, and operating mode setup. These features are only availableon certain TK devices such as DAS data logger. This is the normal dealer level and the default installationmode.Technician AccessUser has all the access granted to Default Users, and in addition will see more information in downloadedloggers data which can be used for maintenance and diagnostics. Technician Access can be selected fromthe Tools Menu.77
- Page 31 and 32: Chapter 4Communicating with your Th
- Page 33 and 34: Chapter 4Communicating with your Th
- Page 35 and 36: Chapter 4Communicating with your Th
- Page 37 and 38: Chapter 4MPIV, MPV, MPVI SettingsCo
- Page 39 and 40: Chapter 4Communicating with your Th
- Page 41 and 42: Chapter 4Communicating with your Th
- Page 43 and 44: Chapter 4Communicating with your Th
- Page 45 and 46: Chapter 4Communicating with your Th
- Page 47 and 48: Chapter 4Communicating with your Th
- Page 49 and 50: Chapter 4Communicating with your Th
- Page 51 and 52: Chapter 4VPRS SettingsCommunicating
- Page 53 and 54: Chapter 4Communicating with your Th
- Page 55 and 56: Chapter 4Communicating with your Th
- Page 57 and 58: Chapter 4Communicating with your Th
- Page 59 and 60: Chapter 4Communicating with your Th
- Page 61 and 62: Chapter 5Managing your WinTrac Data
- Page 63 and 64: Chapter 5Managing your WinTrac Data
- Page 65 and 66: Chapter 5Managing your WinTrac Data
- Page 67 and 68: Chapter 6Viewing your Data Graphica
- Page 69 and 70: Chapter 6Viewing your Data Graphica
- Page 71 and 72: Chapter 7Viewing your Data in Tabul
- Page 73 and 74: Chapter 7Viewing your Data in Tabul
- Page 75 and 76: Chapter 7Viewing your Data in Tabul
- Page 77 and 78: Chapter 8Personalizing the DisplayT
- Page 79 and 80: Chapter 8Personalizing the DisplayT
- Page 81: Chapter 9Advanced WinTrac Features6
- Page 85 and 86: Chapter 9Advanced WinTrac Features6
- Page 87 and 88: Chapter 9Advanced WinTrac FeaturesR
- Page 89 and 90: Chapter 9Advanced WinTrac FeaturesU
- Page 91 and 92: Chapter 9Advanced WinTrac FeaturesC
- Page 93 and 94: Chapter 10Troubleshooting your WinT
- Page 95 and 96: Chapter 10Troubleshooting your WinT
- Page 97 and 98: Chapter 11License AgreementChapter
Chapter 9Advanced WinTrac FeaturesAccessing the Tools Menu in WinTrac 5The Tools menu is new to WinTrac 5. It allows you to perform tasks such as calibrating sensors, Flash loadingTK device with a new version of software, setting up modes on TK devices, etc. Note that only certain devicessuch as DAS data logger will support these features.Launch WinTrac software.Press 'Ctrl' + 'Shift' + 'T' keys simultaneously.You will see the 'Tools' menu appear in the menu bar.Tools MenuNOTE: If the ‘Tools Menu’ does not appear, the user access level may be set to Read Only Access (level 1). Ifthis is the case, the user access level must be changed to Standard User (level 7). Changing the User Accesslevel is described in the next section. You can hide the 'Tools' menu again by pressing 'Ctrl' + 'Shift' + 'T' keyssimultaneously.76