Speed Triple 1050 From VIN - Triumph Instructions.com
Speed Triple 1050 From VIN - Triumph Instructions.com
Speed Triple 1050 From VIN - Triumph Instructions.com
- No tags were found...
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Street <strong>Triple</strong> and Street <strong>Triple</strong> R only3. Remove the seat.All Models4. Disconnect the battery, negative (black) lead first.Note:• The instruments cover is held in place bybayonet type fixings. Gently pull on the coverto release it.5. Remove the cover and gasket attached to the rear ofthe instruments. Retain the cover and gasket if themotorcycle is to be returned to its original condition.8. Position the infill panel to the instruments bracket asshown. Secure with the M6 x 12 mm screws fromthe kit and tighten to 7 Nm.1ccwj_131. Instruments cover2. Bayonet fixings3. Gasket6. Disconnect the electrical connector from theinstrument pack.7. Release the screw and remove the instruments fromthe bracket.12cgpb1. ScrewsNote:• Ensure that the rubber boot on the electricalconnector is positioned over the instrumentsocket and seals the connector.9. Fit the instruments to the infill panel and bracketassembly. Tighten the screw to 3Nm and connectthe electrical connector.44cgpa31. Electrical connector2. Screw3. Washer4. Bayonet fixings21cgpe31. Electrical connector2. Screw3. Washer4. Bayonet fixings21WarningWhen securing electrical cables with cable ties, ensurethe cable ties are fully tight. Ensure there is slack in thecables.Failure to follow this warning may result in damage tothe electrical cables, which may lead to loss ofmotorcycle control and an accident.3 of 5
10. Secure the headlight harness to the instrumentharness with the cable tie provided.<strong>Speed</strong> <strong>Triple</strong> from <strong>VIN</strong> 461332 and<strong>Speed</strong> <strong>Triple</strong> R only13. Refit the front panel to the fuel tank and tighten thefixings to 3 Nm.Street <strong>Triple</strong> and Street <strong>Triple</strong> R only14. Refit the seat.All Modelscgpa1. Headlight harness2. Instrument harness3. Cable tie11. Secure the flyscreen to the infill panel with theM5 x 14 mm screws from the kit. Tighten to 3 Nm.313212WarningMove the handlebar to the left and right full lock whilechecking that the mirrors do not restrict the steering bycontacting the flyscreen.Operation of the motorcycle with restricted steering mayresult in loss of motorcycle control and an accident.CautionMove the handlebar to the left and right full lock whilechecking that the mirrors do not contact the flyscreenwhen moving the handlebar.Damage to the flyscreen will result if the mirrors contactthe flyscreen. If the mirrors do make contact, adjust theirposition.15. If the mirrors contact the flyscreen when on full lock,adjust the mirrors such that they will not contact itand that they give rear visibility in the riding position.16. Remove the motorcycle from the paddock stand.cgpc11. Screws2. Infill panel3. Flyscreen12. Reconnect the battery, positive (red) lead first.WarningAfter fitting the accessory kit the motorcycle will exhibitnew handling characteristics. Operate the motorcycle ina safe area free from traffic to gain familiarity with anynew characteristics. Operation of the motorcycle whennot familiar with any new handling characteristics mayresult in loss of motorcycle control and an accident.WarningIf, after fitment of this accessory kit, you have any doubtabout the performance of any aspect of the motorcycle,contact an authorised <strong>Triumph</strong> dealer and do not ridethe motorcycle until the authorised dealer has declaredit fit for use. Riding a motorcycle when there is anydoubt as to any aspect of the performance of themotorcycle may result in loss of control of themotorcycle, leading to an accident.4 of 5
WarningNever ride an accessory-equipped motorcycle at speedsabove 80 mph (130 km/h). The presence of accessorieswill cause changes in the stability and handling of themotorcycle. Failure to allow for changes in motorcyclestability may lead to loss of control or an accident.Remember that the 80 mph (130 km/h) limit will bereduced by the fitting of non-approved accessories,incorrect loading, worn tyres, overall motorcyclecondition and poor road or weather conditions.WarningOnly operate this <strong>Triumph</strong> motorcycle at high speed inclosed course on road <strong>com</strong>petition or on closed courserace tracks. High speed operation should only beattempted by riders who have been instructed in thetechniques necessary for high speed riding and arefamiliar with the motorcycle’s characteristics in allconditions. High speed operation in any othercircumstances is dangerous and will lead to loss ofmotorcycle control and an accident.WarningThe motorcycle must not be operated above the legalroad speed limit except in closed course conditions.5 of 5