HMC896LP4E - Hittite Microwave
HMC896LP4E - Hittite Microwave HMC896LP4E - Hittite Microwave
v00.0511HMC896LP4EFILTER - TUNABLE, BAND PASS SMT10 - 18 GHzOutline DrawingNOTES:1. LEADFRAME MATERIAL: COPPER ALLOY2. DIMENSIONS ARE IN INCHES [MILLIMETERS]3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE.4. Pin BURR LENGTH SHALL BE 0.15 mm MAXIMUM.Pin BURR HEIGHT SHALL BE 0.05 mm MAXIMUM.5. PACKAGE WARP SHALL NOT EXCEED 0.05 mm.6. ALL GROUND LEADS AND GROUND PADDLE MUST BESOLDERED TO PCB RF GROUND.7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTEDLAND PATTERN.FILTERS - TUNABLE - SMTPackage InformationPart Number Package Body Material Lead Finish MSL Rating Package Marking [1][2] H896HMC896LP4E RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL1XXXX[1] 4-Digit lot number XXXX[2] Max peak reflow temperature of 260 °CFor price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.comApplication Support: Phone: 978-250-3343 or apps@hittite.com6
v00.0511HMC896LP4EFILTER - TUNABLE, BAND PASS SMT10 - 18 GHzPin DescriptionsPin Number Function Description Interface SchematicFILTERS - TUNABLE - SMT1, 2, 4 - 7, 12 - 15,17 - 19, 24GND11, 20 - 23 NC3 RFINThese pins and exposed paddlemust be connected to RF/DC ground.The pins are not connected internally; however, all datashown herein was measured with these pins connected toRF/DC ground externallyThis pin is AC coupled andmatched to 50 Ohms.8 Vnctl Low side/high side notch control voltage.9 Vfctl Center frequency control voltage.10 Vfctl Center frequency control voltage.16 RFOUTThis pin is AC coupled andmatched to 50 Ohms.Application Circuit7For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.comApplication Support: Phone: 978-250-3343 or apps@hittite.com
- Page 1 and 2: v00.0511HMC896LP4EFILTER - TUNABLE,
- Page 4 and 5: v00.0511HMC896LP4EFILTER - TUNABLE,
- Page 8: v00.0511HMC896LP4EFILTER - TUNABLE,
v00.0511<strong>HMC896LP4E</strong>FILTER - TUNABLE, BAND PASS SMT10 - 18 GHzPin DescriptionsPin Number Function Description Interface SchematicFILTERS - TUNABLE - SMT1, 2, 4 - 7, 12 - 15,17 - 19, 24GND11, 20 - 23 NC3 RFINThese pins and exposed paddlemust be connected to RF/DC ground.The pins are not connected internally; however, all datashown herein was measured with these pins connected toRF/DC ground externallyThis pin is AC coupled andmatched to 50 Ohms.8 Vnctl Low side/high side notch control voltage.9 Vfctl Center frequency control voltage.10 Vfctl Center frequency control voltage.16 RFOUTThis pin is AC coupled andmatched to 50 Ohms.Application Circuit7For price, delivery and to place orders: <strong>Hittite</strong> <strong>Microwave</strong> Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.comApplication Support: Phone: 978-250-3343 or apps@hittite.com
Change language