Equipment - Hanes Supply, Inc

More documents

Recommendations

Info

EquipmentBuffalo - Headquarters: 716.826.2636 FAX: 716.826.4412Albany/NE Division: 518.438.0139 FAX: 518.438.5343Rochester Division: 585.235.0160 FAX: 585.235.0229Skidmore-WilhelmTORQUE-TENSION TESTERS• Reduce fastener costs• Establish assembly standards• Assure consistent power tool output• Control product qualityHow Exactly Do You Usea Skidmore-Wilhelm Torque-TensionTester?Determine the exact torque-tensionrelationship to establish tighteningstandards for each applications.The tester lets you easily determinethe joint torque-tension relationship.First, insert the fastener into thetester. Then, tightening the nut createspressure, which is transmitted tothe gage through hydraulic fluid. thegage is calibrated to read directly inpounds tension.As you tighten the fastener with a hand torquewrench, the tester gage registers tension and thetorque wrench registers torque. noting both readingsat a specified point establishes the torque-tensionstandard for the joint.Test power Tool output under StandardConditions with precision test Bolt assemblies.On a day-to-day basis, how do you know your powertools are delivering consistent tightening force eachtime you use them? Easy.With a Skidmore-Wilhelm Torque-Tension Tester, youcalibrate each tool individually and keep a record of itsout-put performance. Then periodically - even everyday - check the tool against its established norm. Anydeviation in output signals the need for adjustment ormaintenance before it affects product quality.Skidmore-WilhelmHanes Supply of SC, Inc.CCISCO: 843.238.1338FAX: 843.238.8337Torque-Tension Testers forSmall, Medium, and Large ApplicationTorque-Tension Tester models are designedaccording to fastener size and type, maximum preload,and, for power tool output testing, the drivesize of the power tool. Special test bolt assembliesfor power tool testing are available for all models.If desired, any model can be ordered with a dualreadinggage that indicates tension in metric unitsas well as pounds.Large Applications:• Fastener: Bolts 1-1/4" through 2-1/2" (M32-M64)• Tension capacity: 225,000 Lbs. maximum• Tool/size: 1" to 2-1/2" square drive• Test bolt assembly: 6 sizes available: 1-1/4" - 2-1/2"Medium Applications• Fastener: High-strength bolts 1*1/8" through1-1/2" (M30-M38)• Tension capacity: 170,000 Lbs. maximum• Tool/size: 3/4" - 1-3/4" square drive• Test bolt assembly: 3 sizes available:1", 1-1/4", 1-1/2"• Fastener: Bolts 5/8" through 1-1/4" (M16-M32)• Tension capacity: 100,000 Lbs. maximum• Tool/size: 1/2" through 1-1/2" square drive• Test bolt assembly: 3 sizes available:3/4", 1", 1-1/4"• Fastener: Screws and bolts #10 through 9/16"(M5-M16)• Tension capacity: 30,000 Lbs. maximum• Tool/size: 1/4" through 3/4" square drive• Test bolt assembly: 2 sizes available: 5/8", 7/8"Model J features a separate low-range gage for easyreading over the tester’s entire operating range.Model RLModel JModel HModel K30EquipmentConsistent, accurate power tool output testing requires standard, repeatabletest conditions. Most importantly, test conditions should simulate asclosely as possible the way the tool is actually used on the job.Production fastners are poorly suited for test purposes and should not beused. They are subject to many variations, and physical changes fromrepeated tightening and retightening can adversely affect the torque-tensionrelationship.Test Bolt AssemblyTo avoid such problems and guaranteestandard power tool test conditions,Skidmore-Wilhelm makes special hardenedally steel test bolt assemblies. firstuse the appropriate-sized assembly toestablish a tool’s performance norm. Theneach time you retest the tool simply usethe same test bolt assembly and comparethe output.Use Skidmore-Wilhelm Torque-Tension Testers to Choose the RightFasteners and Consistently Tighten Them to Specifications.Check fastener strength: During design, your Skidmore-Wilhelm Torque-Tension Tester lets you perform torque-to-yield tests and torque-to-failuretests to determine the right fastener: not simply the strongest fastener, butthe least expensive fastener strong enough to secure the joint. You can spotcheck fastener quality at any time. And because you can place actual jointcomponent samples in the tester, you can study how plating, types of washers,lubrication, and other joint variables affect the amount of torque neededto produce the required tension. In this way the tester lets you establishaccurate torque-tension tightening standards.Check power tool performance: Our testers let you determine the outputof all kinds of power tools - pneumatic, electric, and hydraulic impactwrenches, and nutrunners. You can verify settings for adjustable outputpower tools, periodically check output against established norms, andensure that assembly personnel are using power tools consistently. Tool cribpersonnel or maintenance foremen: you can quickly verify the performanceof new and rebuilt power tools as well as test whether older tools needmaintenance. And because you test your power tools by actually using themin a tightening situation, you closely simulate the tool’s on-the-job operatingconditions. Skidmore-Wilhelm Torque-Tension testers ensure quality consistencyand control.30-28WWW.HANESSUPPLY.COMSmall Applications• Fastener: Machine screws #6, #8, #10, and 1/4'(M3-M6)• Tension capacity: 5,000 Lbs. maximum• Tool/size: Power screwdrivers and small impactwrenchesModel S can be bench-mounted vertically orhorizontally. Ideal for testing small fasteners.Model SAdapter SetsEach Skidmore-Wilhelm Torque-tension Tester comes complete with plateand bushing adapters that allow you to test a variety of hex head bolts andcap screws. Self-tapping screws can also be tested. For shorter lengthbolts, tapped bushings are available.Have an unusual head configuration? Skidmore-Wilhelm can make upspecial adapters. Need metric? Adapter sets are also available in metric.Adapter sets are also available in metric equivalent sizes. See the accompanyingchart to determine which adapter sets come standard with eachtester model.TESTERSTANDARD ADAPTERS FURNISHED FOR USEMODELWITH THE FOLLOWING:Model S #6, #8, #10, & 1/4" fastenersModel J #10, 1/4", 5/16", 3/8", 7/16", 1/2" & 9/16" fastenersModel RL 5/8", 3/4", 7/8", 1", 1-1/8", 1-1/4" fastenersModel H 1-1/8" through 1-1/2"Model K 1-1/4” through 2-1/2" fasteners
Test Bolt AssembliesChoose test bolt assemblies from theaccompanying table based on power toolsquare drive size, tester model and hexsocket size.Buffalo - Headquarters: 716.826.2636 FAX: 716.826.4412Albany/NE Division: 518.438.0139 FAX: 518.438.5343Rochester Division: 585.235.0160 FAX: 585.235.0229TENSION- BOLT TEST POWERTESTER ASSEMBLY BOLT TOOL. HEX MAXMODEL PART NO. SIZE (in) SQ. DR. (in) SOCKET NORMS S-105 5/16 1/4 3/8 5,000J J-110 5/8 3/8, 1/2, 5/8 9/16 15,000J J-114 7/8 5/8, 3/4 7/8 30,000M, ML, RL R-112 3/4 5/8, 3/4 1-1/4 30,000M, ML, RL R-116 1 3/4, 1 1-5/8 70,000M, ,L, RL R120 1-1/4 1, 1-1/4 2 110,000H H-116 1 3/4, 1 1-5/8 70,000H H-120 1-1/4 1, 1-1/4 2 110,000H H-124 1-1/2 1-1/4, 1-1/2 2-3/8 170,000K K-120 1-1/4 1, 1-1/4 2 110,000K K-124 1-1/2 1-1/4, 1-1/2 2-3/8 170,000K K-128 1-3/4 1-1/2, 1-3/4 2-3/4 225,000K K-132 2 1-3/4, 2 3-1/8 225,000K K-136 2-1/4 2, 2-1/4 3-1/2 225,000K K-140 2-1/2 2-1/4, 2-1/2 3-7/8 225,000Other Fastener/Tool TestingProducts and ServicesThe complete Skidmore-Wilhelm product line covers a range of fastenerand assembly tool testing products for both industrial and constructionapplications. Descriptive bulletins are available giving detailed informationon most Skidmore-Wilhelm products.Model M Bolt Tension CalibratorClamps directly to beam or column for on-site calibration of impactwrenches used to tighten high-strength bolts on structural steel. Also testsfastener strength. Accepts bolt diameters 1/2" to 1-1/4", 100,000 Lbs. maximumpreload. Ideal for construction-site fastener testing. Ask for construction-sitefastener testing. Ask for Bulletin 110.Model MS Bolt Tension CalibratorSame functions as Model M, but designed specifically for shorter-lengthconstruction bolts, including Tension-control bolts, 1/2" to 1" in diameter.90,000 Lbs. capacity. Bulletin 112.Model P 3/8” Bolt Tension TesterFor sales demonstrations showing comparative fastener strength. Easilyclamps to a customer’s desk or a bench. Ask for Bulletin 101.Model W Torque Wrench CalibratorFor setting and checking beam, dial reading, or micrometer torque wrenches.Ask for Bulletin 210.Model PT Digital Torque TesterFor checking performance of impact wrenches and hand torque wrenches.Patented electronic design gives direct digital readout of torque in footpoundsor newton-meters. Ask for Bulletin 510.ACCESSORIES:Model LR-100 Hydraulic Load RelieverA hydraulic hand pump that attaches to a testerby means of a quick-disconnect fitting.Simulates service conditions by adding additionalload to a bolt already preloaded inthe tester. Also, by relieving the pressureon a bolt/lock nut assembly, the LR-100 allows measurement of the torquerequired to back off a prevailing torquelock nut - without loosening thenut.Air Timer ControlFoot switch operated air timer controldelivers air to power tool at a set pressurefor a fixed time interval. Electrictimer actuates a solenoid valve thatshuts off air flow after a pre-set interval.Ensures that the true efficiency ofthe tool is the only test variable.Operates on either 110 or 220 volts;connects to existing 3/8" or 3/4" airlines.WWW.HANESSUPPLY.COMHanes Supply of SC, Inc.CCISCO: 843.238.1338FAX: 843.238.8337Skidmore-Wilhelm/ScotchmanEquipmentIronworkerModel 6509-24MStandard Features• Punching Capacity 65 Tons• 9" Throat Depth• Angle Shear Capacity 6" x 6" x3/8" and 5" x 5" x 1/2"• Bar Shear Capacity 24". BladesComplete with 4 Cutting Edges• Tool Table Work Area forMounting Optional Tooling• Die Holder Complete with 2"Die Insert• Remote Foot Pedal• Adjustable Stripper• Adjustable Stroke Controlwith Scale• Two Stage Pump• Jam Nut with Wrench• Electrical Box Supplied withEmergency Palm Button and Lock-out Tag-out Accommodations• 230/460 Volt 3 Phase Electrics• All Guards Necessary to Comply with ANSI B 11-5 Standards• Fork Lift Accommodations• 1-Year WarrantyCapacities & Specifications Rated on 65,000 PSI Tensile A Mild Steel:Throat Depth 9"Punching Cap. 65 Tons1-1/16 " IN 3/4"Special Tooling 4" IN 3/16"Flat Bar Shear 24" Length1" x 6"3/4" x 8"3/16" x 24"Opt. Saber Blade 1/2" x 16"3/8" x 24"Angle Shear 90 6" x 6" x 3/8"Angle Shear 45 4" x 4" x 1/2"Strokes Per Min.Lt. Material 40Max. Capacity 12Channel Shear 2" to 5" Adj.Pickett tool 1/2", 3/4" & 1"Rod Shear 10 CavitiesRound 1/4" to 1-1/4"Square 1/4" to 1"90 V. Notcher 6" x 6" x 5/16"Rectangle Notcher 2" x 2-1/2" x 3/8"Pipe Notching 3/4", 1"Schedule 40 I.D. 1-1/4", 1-1/2" or 2"Brake 12" 40 Ton18" 35 Ton24" 30 TonHydraulics 2,500 PSIMotorsStandardOptionalDimensionsWeight230/460/5HP 3PH200/208/340/380400/415/550/575230 5HP 1PHW-24" L-60" H-66"2,750 Lbs.Note: Six foot back gauge, oversized Punch Table and oversized Shear Table are alsoavailable, please call for more information.IronworkerModel 9012-24MStandard Features• Punching Capacity 90 Tons• 12" Throat Depth• Angle Shear Capacity6" x 6" x 1/2"• Bar Shear Capacity 24". BladesComplete with 4 Cutting Edges• Tool Table Work Area for MountingOptional Tooling• Die Holder Complete with2" Die Insert• Adjustable Stripper• Jam Nut with Wrench• Removable Foot Pedal• Adjustable Stroke Control with Scale• Two Stage Pump• Electrical Box Supplied with EmergencyPalm Button and Lock-out Tag-out Accommodations• 230/460 Volt 3 Phase Electrics• All Guards Necessary to Comply with ANSI B 11-5 Standards• Fork Lift Accommodations• 1-Year Warranty– continues –30-2930Equipment
Page 1 and 2: Buffalo - Headquarters: 716.826.263
Page 13 and 14: Hydraulic Hand Held Saw (continued)
Page 15 and 16: Wheeled Portable CompressorsThese w
Page 17 and 18: Hand-Carry Compressors (continued)H
Page 19 and 20: Model HCP 420UT No. 01609• Honda
Page 21 and 22: SLX2Self-Leveling/2-Beam (Plumb, Le
Page 27 and 28: Series 8 Mark IIOne of the most pop
Page 29: Heavy Duty NGD SeriesThe NAC Heavy
Page 33 and 34: Concrete Mixers (continued)Buffalo

Equipment - Hanes Supply, Inc

Create successful ePaper yourself

Delete template?

Save as template?