Equipment - Hanes Supply, Inc

More documents

Recommendations

Info

30EquipmentEquipmentTurbo-Burr ®• Easily brought to the work site• For use as both a hand and bench tool• Puts a safety edge on sheet metal inone pass• Breaks sharp edges on parts at mill,saw or shearPerfect for deburring and edge finishing of:– Ferrous and non-ferrous metals– Plastics– Stainless steel– Aluminum– Laminates– Printed circuit boardsHomeliteGENERATORSModel CG 4800UT No. 03762• 8 HP Honda OHV engine• Large 7.5 gal. fuel tank• Run time - 11 hrs. per tank of fuel at full load• Automatic idle control to increase fuel economyand extend engine life• Outlets - two 15A 120V (5-15R)- one 20A 120V (L5-20R)- one 30A 120V (L5-30R)- one 20A 120V/240V (L14-20R)• Solid-state voltage regulation 2%• Vibration isolation mounts for extra long life• Protective roll cage*30-16Buffalo - Headquarters: 716.826.2636 FAX: 716.826.4412Albany/NE Division: 518.438.0139 FAX: 518.438.5343Rochester Division: 585.235.0160 FAX: 585.235.0229Two Models:Model S With closed bottom “V” block.Suitable for most applications.Model R With a small gap at the bottom of the “V”block. Suitable for materials 0.135 inchesand heavier, where large burrs are present.Rotation Speed: 55,000 rpm (no load speed)Air Consumption: 5 to 11 cfm-lubrication not neededAir pressure: 60 to 120psiAir Hose: 1/4 inchMin. Material Thickness: .015 inchCollet: 1/4 inch - compression typeBurr Type: 1/4 in. dia. x 2 in. lengthoverall-solid carbideDepth of Bevel: 0 to .075 in. at 45°Feed Speeds: up to 2 in. per secondWeight: 3.5 lbs.Beveling Table• Beveling angles infinitely adjustable from 25-90 degrees• Beveling fixture constructed of sturdy anodized aluminum, work table ofprecision ground steel• Micrometer type depth adjustmentallows for precise set-up andoperation• Dual exhaust manifoldFor beveling and edge finishing of:– Printed circuit boards– Plastics– Connector finger tips– Wood– CompositesRotation Speed: 55,000 rpm (no load speed)Air Consumption: 5 to 11 cfm-lubrication not neededAir pressure: 60 to 120psiAir Hose: 1/4 in.Max Material: 1/2 in. thick at 900Collet: 1/4 in. - compression typeBurr Type: 1/4 in. dia. x 2 in. lengthoverall-solid carbideDepth of Bevel: 0 to 1/2 in. at 45° multiple passesFeed Speeds: up to 2 in. per secondTable size: 8-3/4 in. deep x 16 in. longDim. (L x W x H): 16 x 17 x 8-3/4 in.Weight: 35 lbs.WWW.HANESSUPPLY.COMHanes Supply of SC, Inc.CCISCO: 843.238.1338FAX: 843.238.8337Heck Industries, Inc./HomeliteHY-CYCLE GENERATORModel CHY 5000UT No. 03772• 11 HP Honda engine• Large 7.5 gal. fuel tank• Run time - 9 hrs. per tank of fuel at full load• Automatic idle control to increase fuel economyand extend engine life• Vibration isolation mounts for extra long life• Protective roll cage*Model CG 6300UT No. 03763• 11 HP Honda OHV engine• Large 7.5 gal. fuel tank• Run time - 9 hrs. per tank of fuel at full load• Automatic idle control• Full power 120 volt switch• Outlets - two 15A 120V (GFCI)- one 20A 120V (L5-20R)- one 30A 120V (L5-30R)- one 20A 120V/240V (L14-20R)• Solid-state voltage regulation 2%• Vibration isolation mounts for extra long life• Protective roll cage*Model CGE 6300UT No. 03764• 11 HP Honda OHV engine• Large 7.5 gal. fuel tank• Run time - 9 hrs. per tank of fuel at full load• Automatic idle control• Full power 120 volt switch• Outlets - two 15A 120V (GFCI)- one 20A 120V (L5-20R)- one 30A 120V (L5-30R)- one 20A 120V/240V (L14-20R)• Solid-state voltage regulation 2%• Electric key start• Protective roll cage*Generator Specifications:Model CG 4800 CG 6300 CGE 6300 CHY 5000UT No. 03762 03763 03764 03772Watts (Int.) 4800 6300 6300 –Watts (Cont.) 4000 5000 5000 5000Volts AC 120/240 120/240 120/240 230Amps AC 120/240 33.3/16.6 41.6/20.8 41.6/20.8 12.6CPS (Hz) 60 60 60 180Low Oil shut-Off YES YES YES YESHP @ 3600 RPM 8 11 11 11Run Time/ 11 hrs./ 9 hrs./ 9 hrs./ 9 hrs./Tank Size 7.5 gals. 7.5 gal. 7.5 gals. 7.5 gsls.Voltage Regulation +/-2% +/-2% +/-2% InherentIdle Ctrl. Std. Std. Std. Std.Net Wt. (lbs) 158 177 205 194CENTRIFUGAL PUMPSModel 111 S2UT No. 01532• Briggs & Stratton 3.5 HP, 1/P 4-cycle engine• Pumps 9,000 GPH (34,000 L/hr.)• Total head - up to 110 ft. (33.5m)• Priming Lift - 25 ft. (8.5m) at sea level• Open type abrasion resistant iron impeller• Abrasion resistant cast iron impeller housing• 2" suction and discharge• Protective roll cage with rubber feet*
Model HCP 420UT No. 01609• Honda 4 HP, 4-cycle engine• 2" (5 cm) suction and discharge• Pumps 9,225 GPH (34,920 L/hr.)• Total head - 92 ft. (28 m)• Priming lift - 25 ft. (7.6 m) at sea level• Abrasion resistant cast iron impeller• Protective roll cage*• Silicon carbide sealModel 120 S3UT No. 01535• Briggs & Stratton I/P 8 HP engine• Pumps 17,600 GPH (66,620 L/hr.)• Total head - up to 113 ft. (34.4m)• Priming Lift - 25 ft.(7.6m) at sea level• Open type abrasion resistant cast ironimpeller• Abrasion resistant cast iron impeller housing• 3" suction and discharge• Protective roll cage*• Vibration isolationModel HCP 630UT No. 01610• Honda 5.5 HP, 4-cycle engine• 3" (7.6 cm) suction and discharge• Pumps 15,915 GPH (60,240 L/hr.)• Total head - 92 ft. (28 m)• Priming lift - 25 ft. (7.6 m) at sea level• Abrasion resistant cast iron impeller• Protective roll cage*• Silicon carbide seal* Dolly kit optionCentrifugal Pump Specifications:Buffalo - Headquarters: 716.826.2636 FAX: 716.826.4412Albany/NE Division: 518.438.0139 FAX: 518.438.5343Rochester Division: 585.235.0160 FAX: 585.235.0229Model 111 S2 120 S3 HCP 420 HCP 630UT No. 01532 01535 01609 01610Suc./Dis. Size (in) 2 3 2 3Capacity GPH/ 9,000 17,600 9,225 15,915(L/hr.) (34,000) (66,620) (34,920) L/hr (60,240)L/hrTotal Head (ft) 110 113 92 92Priming Time inSec @ 25 ft. Lift 84 88 240 287Engine Briggs & Stratton Briggs & StrattonI/P 4-cycle I/P 4-cycle Honda OHV Honda OHVHP 3.5 8 4 5.5Low Oil Shut-Off N/A Yes Yes YesRun Time 1 hr. 1.5 hrs. 2.3 hrs. 2 hrs.Net Weight- (lbs) 60 110 46.5 59.4TRASH PUMPSModel 121 TP2UT No. 01540• Briggs & Stratton 5 HP, 1/P 4-cycle engine• Pumps 10,400 GPH (39,300 L/hr.)• Priming Lift - 25 ft.(7.6m) at sea level• Open type abrasion resistant cast iron impeller• Abrasion resistant cast iron impeller housing• 2" suction and discharge• Handles 1" solids• Protective roll cage with rubber feet*Model 120 TP3UT No. 01537• Briggs & Stratton 8 HP, I/P 4-cycle engine• Pumps 19,680 GPH (74,500 L/hr.)• Priming lift - 25 ft. (7.6 m) at sea level• Open type abrasion resistant cast ironimpeller• Abrasion resistant cast iron impeller housing• 3" suction and discharge• Handles 1.5” solids• Protective roll cage*• Vibration isolationHomeliteWWW.HANESSUPPLY.COMHanes Supply of SC, Inc.CCISCO: 843.238.1338FAX: 843.238.8337Model HTP 2UT No. 01601• Honda 5.5 HP OHV 4-cycle engine• Pumps 10,400 GPH (39,300 L/hr.)• Priming lift - 25 ft. (7.6 m) at sea level• Open type abrasion resistant cast iron impeller• Abrasion resistant cast iron impeller housing• 2" suction and discharge• Handles 1" solids• Protective roll cage with rubber feet*Model HTP 3UT No. 01602• Honda 8 HP OHV 4-cycle engine• Pumps 19,680 GPH (74,500 L/hr.)• Priming lift - 25 ft. (7.6 m) at sea level• Open type abrasion resistant cast iron impeller• Abrasion resistant cast iron impeller housing• 3" suction and discharge• Handles 1.5" solids• Protective roll cage*• Vibration isolationModel VTP 4UT No. 01605• Briggs & Stratton 16 HP Vanguard OHV 4-cycle engine• Pumps 39,720 GPH (150,340 L/hr.)• Priming lift - 25 ft. (8.5 m) at sea level• Open type abrasion resistant iron impeller• Abrasion resistant cast iron impeller housing• 4" suction and discharge• Handles 2" solids• Protective roll cage & dolly standard*Trash Pump Specifications:EquipmentModel 121 TP2 HTP 2 120 TP3 HTP 3 VTP 4UT No. 01540 01601 01537 01602 01605Suc./Dis. Size (in) 2 3 3 3 4Capacity GPH/ 10,400 10,400 19,680 19,680 39,720(L/hr.) (39,300) (39,300) (74,500) (74,500) (150,340)Total Head (ft) 108 108 93 93 115Priming Time inSec @ 25 ft. Lift 62 62 70 70 80Engine Briggs & Honda Briggs & Honda Briggs &Stratton OHV Stratton OHV StrattonI/P 4-cycle 4-cycle I/P 4-cycle 4-cycle VanguardOHVHP 5 5.5 8 8Low Oil Shut-Off Std. Std. Std. Std. Std.Run Time (hr) 1.68 1.2 1.75 1.85 1.1Net Weight- (lbs) 74 79.5 115 119 350DIAPHRAGM PUMPSModel HDP 2UT No. 01603• Honda 4 HP OHV engine• Pumps 2,000 GPH (7,600 L/hr.)• Total head - up to 50 ft. (15 m)• Priming Lift - 25 ft. (7.6 m) at sea level• 2" suction and discharge• Protective roll cage*Model HDP 3UT No. 01604• Honda 5.5 HP OHV engine• Pumps 4,800 GPH (18,200 L/hr.)• Total head - up to 50 ft. (15 m)• Priming Lift - 25 ft. (7.6 m) at sea level• 3" suction and discharge• Protective roll cage** Dolly kit optional30-1730Equipment
Page 1 and 2: Buffalo - Headquarters: 716.826.263
Page 13 and 14: Hydraulic Hand Held Saw (continued)
Page 15 and 16: Wheeled Portable CompressorsThese w
Page 17: Hand-Carry Compressors (continued)H
Page 21 and 22: SLX2Self-Leveling/2-Beam (Plumb, Le
Page 27 and 28: Series 8 Mark IIOne of the most pop
Page 29 and 30: Heavy Duty NGD SeriesThe NAC Heavy
Page 31 and 32: Test Bolt AssembliesChoose test bol
Page 33 and 34: Concrete Mixers (continued)Buffalo

Equipment - Hanes Supply, Inc

Create successful ePaper yourself

Delete template?

Save as template?