Interior Timber Guide The best Interior Timber Project Guide ... - Wattyl

INTERIOR STAINS AND VARNISHES03/04PROJECT USAGEGUIDETimber ConditionsPaintedClear CoatedStainedBareSurface PreparationHOW TO STAIN & FINISHINTERIOR FURNITURE}AND TRIMSUse our easy step by step guide to help you through the preparation,staining and finishing of an item of furniture.Preparation MethodThere are different methods of preparing your timberprior to staining. This will depend on the conditionand coating on your timber.1. Ensure that your timber is dry and free fromany wax, grease and dust.2. Coarse sand the surface to prepare with120 grit paper.3. Final sand with up to 400 grit paper. Alwayssand in the direction of the timber grain.4. Remove all dust.5. Nail holes or cracks should be filled withWattyl Timber putty in a matching timber colour.Use paint stripper or sand with coarse abrasive paper to remove the coating.Then fine sand and thoroughly clean before re-coating.Use paint stripper or sand to remove the coating if required. Then fine sand andthoroughly clean before re-coating.Use paint stripper to remove some of the stain depending upon thetype of stain.Fill any holes or cracks with timber putty. Coarse sand the surface with120 grit sandpaper. Then fine sand and thoroughly clean before re-coating.Applying the STAIN1. Apply interior stain liberally with a lint free,clean cloth pad, rubbing the stain in witha circular motion.2. Allow to stand for 1-3 minutes before removingthe excess by vigorously wiping along the grainwith a clean cloth.3. One coat only is required. Further coats will darkenthe colour and may mask the timber grain.4. Allow to dry for 4 hours and then applya Wattyl Estapol Interior Clear as a topcoat toprovide protection, true colour and the desiredgloss level.WattylCOLOURWOODINTERIOR STAINWattyl Colourwood Interior Stainis a semi-transparent, easy to use,pigment-based wood stain designedto produce a rich natural colouringand even toning on all timbers.It penetrates into the timber to enrich andhighlight the natural timber grain and texture.Wattyl Colourwood Interior Stain is ideal forwhitewood and pine timbers and may be used onfurniture, wall panelling, doors, window frames,skirting boards and kitchen cupboards.WengeLiming WhiteWattyl ColourwoodInterior StainCharacteristics: A semi-transparent, easy to use,pigment-based wood stain designed to producea rich natural colouring and even toning on alltimbers. It penetrates into the timber to enrichand highlight the natural timber grain andtexture.Use on: All interior timber such as louvredoors, woodwork, built-in furniture and timberpanelling.Apply with: Brush or clothTouch dry: 1 hourRecoat: 4 hoursClean up: TurpsCoverage: Up to 16m2 per litreNo of coats: 1 coat6. Allow to dry for at least 30 minutes andsand smooth.Handy HintSOn large areas, stain one sectionat a time to ensure the stain does notdry before the excess is removed.If a completely smooth, even surfaceis desired, fill open grained timberswith Wattyl Grain Filler as per labeldirections.New Baltic PineWestern CedarAmerican RedwoodJarrahNordic TeakEnglish Mahogany4Walnut BrownTraditional CedarPrinted images may not be a true representation of the actual colour.Stain colour will appear different on different timbers.

INTERIOR CRAFTSMAN STAIN11/12Wattyl CRAFTSMANTRADITIONAL STAINWattyl Craftsman Traditional Stainis a traditional dye type stain suitablefor interior use.This product has been used by quality furniturecraftsmen for over 40 years and, in capable hands,a professional finish can be achieved on cupboards,wall panelling, doors, built-in furniture, free standingfurniture, bookshelves, tables and chairs. Notrecommended for use on absorbent timbers,pine, particle board and MDF.Traditional stain is touch dry in 30 minutes andcan be re-coated after 4 hours with a Wattyl Estapolclear finish.Wattyl Craftsman Traditional Stain ReducerThis product has been specially formulated toreduce Wattyl Craftsman Traditional Stain to lightenthe applied colour. It is also recommended for useas a cleaning solvent for all equipment used in theapplication of Wattyl Craftsman Traditional Stain.Wattyl CraftsmanTraditional StainCharacteristics: A traditional dye type stainsuitable for interior use. This product has beenused by quality furniture craftsmen for over 40years and provides a professional finish.Use on: Cupboards, wall panelling, doors, built-infurniture, free standing furniture, bookshelves,tables, chairs, etc.Apply with: Brush or clothTouch dry: 30 minutesRecoat: 4 hoursClean up: Wattyl Craftsman Traditional Stain ReducerCoverage: Up to 12m2 per litreNo of coats: 1 coatGolden OakTeakContemporary MapleJarrahDark MahoganyRosewoodCedarNew MapleWalnutBlackPrinted images may not be a true representation of the actual colour.Stain colour will appear different on different timbers.WATTYLCraftsmanNaturalTEAK OILTRANSPARENTWattyl Craftsman Natural Teak OilTeak Oil produces a natural oil finish on Teak andother timbers. It imparts a very smooth feel to thefinish popular with Danish style furniture and interiorteak timber surfaces. Use it as your final coat overWattyl Estapol Interior Polyurethane Matt, as anoil finishing system on new timber, or to rejuvenatean old piece of oiled timber.Wattyl Craftsman NaturalTeak Oil TransparentCharacteristics: Produces a natural oil finish onteak and other timbers. Recommended as a topcoat over Wattyl Estapol Interior PolyurethaneMatt. It is designed to impart a very smooth feelto the finish.Use on: Teak, new timber or to rejuvenatepreviously oiled timberApply with: ClothTouch dry: 12 hoursRecoat: N/AClean up: TurpsCoverage: Up to 20m2 per litreNo of coats: 1 coat

13/14PROJECT USAGEGUIDEHOW TO APPLYWATTYL PREPARATORY}PRODUCTSPreparation is the most important step to ensuring that your timber projecthas the best possible finish. Our preparation guide will give you informationon Sanding, using Putty and grain filler.SANDINGThoroughly sand the surface to prepare it with60-120 grit sandpaper working along the grain,not across the grain and gradually introducea finer (up to 400 grit) sandpaper to finish.Handy Hint: exert even pressure with sandpaperand gradually reduce to a finer 400 grit paper.When to use a timberpreparation productWattyl Colourwood Interior Timber Puttyshould be used to fill gaps, nail holes or cracksin the grain.Wattyl Craftsman Sanding Sealer should beused to effectively seal and fill the grain ofuntreated timber surfaces and raises thegrain for easier sanding.Application steps:1. Stir thoroughly before and during use witha flat stirrer.2. Apply one coat direct from the can usinga quality brush, roller or spray gun.3. Allow 3 hours to dry, then sand lightly in thedirection of the grain with fine sandpaperbefore applying the required finishing coats.Application Steps:1. Press the putty lightly into position with fingeror putty knife leaving a little standing abovethe surface.2. Allow to dry for at least 30 minutes beforesanding smooth.INTERIORPREPARATORYPRODUCTSWattyl Craftsman Grain Filler should be usedon open grained timbers such as Maple, Walnutor Cedar to achieve a perfectly smooth surface.Application Steps:1. Apply grain filler with a piece of hessianor coarse cloth.2. Rub well into the timber grain using a circularmotion.3. Allow to dry for 5 to 8 minutes until the“wet look” disappears.4. Remove excess Grain Filler by rubbing across thegrain with a clean piece of hessian or coarse cloth.5. Finish by rubbing lightly along the grain to removeany cross streaks.6. Do not sand.7. Allow to dry a minimum of 24 hours before coating.2

ESTAPOLFLOOR FINISHES& COLOURWOODFLOORING STAINSPROJECT USAGEGUIDETimber ConditionsPaintedClear CoatedBare}Preparation MethodHOW TO APPLYWATTYL ESTAPOLFLOORING 7008Thoroughly sand surface back to bare timber. Fill any holes or cracks with timberputty. Sand the surface to prepare it with 120 - 240 grit sandpaper.Surfaces with existing Wattyl Estapol Flooring 7008 may be over coatedfollowing suitable preparation. For existing finishes other than Wattyl EstapolFlooring 7008, sand back to bare timber. Fill any holes or cracks with timber putty.Fill any holes or cracks with timber putty. Sand the surface to prepare it with120 - 240 grit sandpaper.21/22Surface PreparationThere are different methods of preparing your timberprior to coating. This will depend on the conditionand coating on your timber.To produce a timber floor with a truly professionallook and feel refer to the appropriate preparationmethod and follow the steps to apply the finish.Applying the Finish1. All timber floor boards must be thoroughlysanded, clean, dry and free from wax, greaseand dust.2. Carefully measure and mix equal quantities ofWattyl Estapol Flooring 7008 Part A and Part B.3. Stir thoroughly with a wide flat stirrer and allow tostand for a minimum of 5 minutes, then stir againbefore use. Ensure the product does not aerateas this will produce bubbles in the finish. Do notshake.4. Apply with a Wattyl Lambswool Floor Applicatoror a quality brush.5. Apply 2 to 4 full, even coats, allowing a minimumof 6 hours and a maximum of 24 hours betweencoats.6. Sand lightly between 1st, 2nd and 3rd coats.Wattyl premium qualityrange of stain coloursare designed to enhancethe natural beauty ofinterior timbers.What is the difference between a one packand two pack clear floor finish?Wattyl Estapol Flooring 7008 is a two pack finish.Part A and Part B need to be mixed togetherbefore application. It has the highest gloss leveland has a very high resistance to chemicals.This makes it especially suitable for bench topsas well as timber floors.Wattyl Estapol Flooring Moisture CurePolyurethane is a one pack finish. It has highwear resistance, is flexible and is scratchresistance, making it ideal for floors in hightraffic areas.4

ESTAPOL FLOOR FINISHES & COLOURWOOD FLOORING STAINS25/26Wattyl ESTAPOLFLOORINGWater basedSPEED CLEARSatin and glossWattyl Estapol Flooring Water BasedSpeed Clear is a tough, one pack, waterbased polyurethane finish which hasbeen specifically designed to beautify,protect and preserve interior tongueand groove, parquetry and corkflooring.Combining ease of application with quick dryingproperties, this water based floor finish enables timberand cork floors to be clear finished within a day.Wattyl Estapol Flooring Water Based Speed Clear has anabrasion resistant formulation which resists scratchingand scuffing, whilst highlighting the natural grain,colour and texture of the timber. Additionally, theexceptionally low odour of this product will ensure amore pleasant environment during application, andwhile drying. It is available in gloss and satin finishes.Wattyl Estapol FlooringWater Based Speed ClearGloss and SatinCharacteristics: A tough, one pack, water basedpolyurethane finish which has been specificallydesigned to beautify, protect and preserveflooring.Use on: Interior tongue and groove, parquetryand cork flooring.Apply with: Brush or applicatorTouch dry: 30 minutesRecoat: 3 hoursClean up: WaterCoverage: Up to 10-16m2 per litre per coatNo of coats: 2-3 coatsWattyl ESTAPOLFLOORINGOIL MoDIFIEDPOLYURETHANESatin and glossWattyl Estapol Flooring Oil ModifiedPolyurethane is a tough, durable,wear resistant polyurethane coatingfor use on timber and parquetry floors.Wattyl Estapol Flooring Oil Modified Polyurethane iseasy to apply and provides a clear finish which enhancesand highlights the timber’s natural grain and warmth.Wattyl Estapol Flooring Oil Modified Polyurethane isparticularly suited for use on new timber floors, commonlyprone to shrinkage, to reduce the risk of edge gluing.Wattyl Estapol Flooring Oil Modified Polyurethaneprovides a durable finish that resists cracking and chippingand is easily maintained and repaired. It is ideally suitedfor use on most types of domestic timber and parquetryflooring, as well as floors subjected to heavy traffic,such as community halls, factories, public buildings andgymnasiums etc. Wattyl Estapol Flooring Oil ModifiedPolyurethane is also suitable for use on most interiorwoodwork, such as built-in-furniture, skirting boardsand panelling. It is available in gloss and satin finishes.Wattyl Estapol FlooringOil Modified PolyurethaneSatin & GlossCharacteristics: A tough, durable, wear resistantpolyurethane. Easy to apply and provides aclear, contemporary finish which enhances andhighlights the timbers natural grain and warmth.Use on: Most types of domestic timber andparquetry flooring, as well as floors subjected toheavy traffic such as community halls, factories,public buildings and gymnasiums.Apply with: Brush, applicator or rollerTouch dry: 2 hoursRecoat: 12 hoursClean up: TurpsCoverage: Up to 10m2 per litre per coatNo of coats: 2-3 coats

ESTAPOL FLOOR FINISHES & COLOURWOOD FLOORING STAINS29/30Wattyl ESTAPOLFlooring TUNG OILPOLYURETHANESUBDUED glossWattyl Estapol Flooring Tung OilPolyurethane is a deep penetrating,wear resistant clear timber coatingsuitable for use on clear timber floorswhere a traditional subdued glossfinish is desired.The coating bonds and penetrates timber fibresand forms a tough protective barrier. It is also suitablefor use on most interior woodwork, such as built-infurniture,skirting boards and panelling. Wattyl EstapolFlooring Tung Oil Polyurethane provides a durablefinish that resists cracking and chipping and is easilymaintained and repaired. It is ideally suited for useon most types of domestic timber and parquetryflooring, as well as floors subjected to heavy traffic,such as community halls, factories, public buildings andgymnasiums etc. It can be re-coated after 12 hours.Wattyl Estapol FlooringTung Oil PolyurethaneSubdued GlossCharacteristics: A deep penetrating, wearresistant clear timber coating predominantly foruse on timber floors where a traditional subduedgloss finish is desired.Use on: Timber floors, most interior woodwork,such as built-in furniture, skirting boards andpanelling.Apply with: Brush, applicator or rollerTouch dry: 1 hourRecoat: 12 hoursClean up: TurpsCoverage: Up to 10m2 per litre per coatNo of coats: 2-3 coatsWattyl ESTAPOLFLOORING SLATE SEALERGlossWattyl Estapol Flooring Slate SealerGloss provides a tough protectivecoating for a range of interior andexterior surfaces.It will help resist penetration from spillages such asoil, grease and food, and is suitable for applicationto surfaces subject to domestic foot and car traffic.It helps bind exposed aggregate and pebble crete,while strengthening masonary surfaces againsteroding and dusting.Wattyl Estapol Flooring Slate Sealer Gloss will notyellow over time and is resistant to exposure fromsunlight. Suitable for use on a variety of surfacesincluding exposed aggregate, slate, pebble finishes,concrete (including stampled/stencilled), brick andsandstone in both interior and exterior applications.It is not suitable for timber surfaces.Wattyl Estapol FlooringSlate Sealer ThinnerThis product has been specially formulated to thinWattyl Estapol Flooring Slate Sealer Gloss to ensuremaximum surface penetration from the first coat. Itis also recommended for use as a cleaning solutionfor all equipment used in the application of WattylEstapol Flooring Slate Sealer Gloss.Wattyl Estapol FlooringSlate Sealer GlossCharacteristics: Provides a tough protectivecoating for a range of exterior and interiorsurfaces.Use on: Suitable for use on a variety of surfacesincluding exposed aggregate, slate, pebblefinishes, concrete (including stamped andstencilled), brick and sandstone.Apply with: Brush or rollerTouch dry: 1 hourRecoat: 2 hoursClean up: Wattyl Estapol Slate Sealer Thinnerand rinse in warm waterCoverage: Up to 5-10m2 per litre per coatNo of coats: 1-2 coats