Double-Dry-nOn-cooled-Probe - Webshop, Gas Analysis Technology

More documents

Recommendations

Info

Unit Operation InstructionDDOP Probe2.4.2 WARNING – TOXIC, EXPLOSIVE GASESSign:Be sure to observe the safety regulations for the respective gases (sample gas and testgases/span gases) and test gas cylinders! The gas outlet should be led to ambient air toavoid danger to operators.Inflammable or explosive gas mixtures must not be introduced into the analysis systemunless the system is designed for the application.To avoid danger to operators by explosive, toxic or unhealthy gas components, flush thegas lines with ambient air or nitrogen before cleaning or exchange parts of the gas paths.2.4.3 WARNING - ACIDSSign:To avoid danger to operators by acid droplets build up in gas lines, first flush the gas linesbefore cleaning or exchange parts of the gas paths.Always use skin and eye protection before cleaning or exchanging parts of the gas pathsincluding condensate trap.2.4.4 WARNING - BURNSSign:To avoid the danger of operators getting burned due to high temperatures of probe andother components, the demands of occupational health regulations should be followed.Always plug the hole to the process when the probe is removed from the flange. The plugmust be secured with the lock pin.2.4.5 WARNING - PRESSUREESign:To avoid danger to operator the hoses must be without pressure before dismounting of anyconnections or hoses.2.4.6 WARNING – MOVING MACHINERYSign:Do not remove covers from Extraction Device with compressed air pressure to ExtractionDevice.Drawing no: 53895-DDOP-450-20 Page 5 of 14
Unit Operation InstructionDDOP Probe3 TECHNICAL INFORMATION DDOP PROBEDimensions:Total, LxWxHSample Filter:MaterialFilter size640x330x220mmAISI 316L20µm ,102xØ50/40Process conditions:Available length for insertion in process400mmTemperature Max. 400°CDust load Max. 200 g/m 3Weight:Weight, dry:26 kgTemperatures:Ambient temperature: -10°C to 55°C 1Storage temperature: -15°C to 55°CEquipment must be protected against heatradiationConnections:Sample line connection:6 mm stainless steel SwagelokBlow Back hoses10 mm stainless steel SwagelokHose clampsSpecified according to actual sample gas hosediameter.Flange for mounting probeSee Drawing “DDOP Probe”Flange is supplied by FLSmidth AirloqCompressed air:Pressure:600 kPaRange 550-750 kPaConsumption:1 Nm3/h at 600 kPaQuality: 3-3-3 according to ISO 8573-1Maximum 5 mm (size) 5 mg/m3 particlesMinimum -20° water pressure dew point**Pressure dew point must be minimum -10°Cbelow minimum ambient temperature at anytime.Maximum 1 mg/m3 oil3.1 PHYSICAL DISTANCE BETWEEN EQUIPMENTThis information is covered by the system manual.1 Probe must be protected to prevent condensation and freezing.Drawing no: 53895-DDOP-450-20 Page 6 of 14
Page 1 and 2: Double-Dry-nOn-cooled-ProbeDDOPUSER
Page 3 and 4: Unit Operation InstructionDDOP Prob
Page 5: Unit Operation InstructionDDOP Prob
Page 15 and 16: Document List:Unit ManualRevision L
Page 17 and 18: 218W1-08326 635W1-04W1 W1-05 W1-063
Page 20 and 21: Part listGas Monitoring UnitPart ID
Page 22: Part listRecommended wear parts for

Double-Dry-nOn-cooled-Probe - Webshop, Gas Analysis Technology

Create successful ePaper yourself

Delete template?

Save as template?