MODEL DG535 Digital Delay / Pulse Generator - SLAC

More documents

Recommendations

Info

SAFETY AND PREPARATION FOR USE******CAUTION******This instrument may be damaged if it isoperated with the LINE VOLTAGESELECTOR set for the wrong ac line voltageor if the wrong fuse is installed.LINE VOLTAGE SELECTIONThe <strong>DG535</strong> operates from a 100V, 120V,220V or 240V (50 or 60 Hz) ac power source.Before applying a power source, verify thatthe line voltage selector card (located in therear panel power entry module) is in thecorrect position. The selected voltage may beseen through the clear window by viewing thepower entry module from below.To change the line voltage selection, removethe line cord, slide the window to the right,and pull the "fuse pull" lever out. Verify thatthe correct fuse is installed for the ac linevoltage: 1 Amp for 100 or 120V, and 1/2 Ampfor 220 or 240V. Pull out the line voltageselector card with a pair of needle nose pliers,and insert it with the correct line voltagefacing the bottom of the instrument andtowards the line cord. Verify that the correctline voltage can be seen through the slot that isjust above thefuse holder. Push the fuse holderback in, and install the correct fuse. Slide thewindow to the left, and replace the line cord.LINE CORDThe <strong>DG535</strong> uses a three wire power cord forconnection to the power source and to aprotective ground. The exposed metal parts ofthe instrument are connected to the outletground: to protect against electrical shock,always use an outlet which has a properlyconnected protective ground.To avoid shock or injury do not removeproduct covers or panels. Do not operate theproduct without all covers and panels in place.CONNECTION TO OTHERINSTRUMENTSAll front panel BNC shields are connected tothe chassis ground and to the power outletground via the power cord. Do not apply anyvoltage to either the shields or to the outputs.The outputs are not protected againstconnection to any potential other than ground.v
QUICK START INSTRUCTIONS(1) Make certain that the correct line voltage is selected on the rear panel.(2) Press the power button "in" to turn on the unit.(3) Press the RECALL Menu key, the "0" digit, and the EXC key in sequence torecall default settings.(4) Press the left cursor key (
Page 1 and 2: MODEL DG535Digital Delay / Pulse Ge
Page 3 and 4: Time Delay vs Repetition 9GPIB PROG
Page 5: Sheet #2 10 MHz Reference and 80 MH
Page 9 and 10: ABRIDGED COMMAND LISTINITIALIZATION
Page 11 and 12: GUIDE TO OPERATIONINTRODUCTIONThe D
Page 13 and 14: is remedied.To use the timebase in
Page 15 and 16: It is often desirable to trigger th
Page 17 and 18: STORE and RECALL MENUSThere are ten
Page 19: other. The pulling of one channel b
Page 22 and 23: 10.0MHz reference is too small or m
Page 24 and 25: incorrect cursor mode will have no
Page 26 and 27: and a trigger input impedance of 50
Page 28 and 29: GPIB PROBLEMSThe first requirement
Page 30 and 31: CALIBRATION MENUSTo access the cali
Page 32 and 33: CIRCUIT DESCRIPTIONThe DG535 has th
Page 34 and 35: threshold, reference oscillator fre
Page 36 and 37: Each of the four delay channels beh
Page 38 and 39: portion of the delay is complete, A
Page 40: +10.000VDC reference is generated o
Page 43 and 44: C 301G 5-00056-512 .1U Cap, Stacked
Page 45 and 46: Q 302C 3-00177-321 2N2222 Transisto
Page 47 and 48: U 109 3-00201-340 MC10H105 Integrat
Page 52 and 53: FAST TRANSITION-TIMEMODULESOPTION 0
Page 54: SETUP FOR OUTPUT STEPS UP TO15 VOLT

MODEL DG535 Digital Delay / Pulse Generator - SLAC

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?